This instructional guide focuses on the techniques for centering and shaping a wide-base clay platter or bowl. The instructor emphasizes the importance of patience, the reduction of friction to maintain clay strength, and specific trimming methods to prevent structural failure during firing.
Slab centering. So I'm going to do a wider base. So when I'm opening, the right thumb is helping it
to drag and pull the wall toward the side of it. If you're opening and you accidentally
knock it off center, how would you fix it? You mean like this? Yeah.
The key is keep your hand steady, right? So you just hold. You don't pull, yeah. You just
maybe push it down. I can reverse throw it, right? See that? I push the clay down, right? Reverse it.
So you just gather it, hold the clay and gather the clay, and then I squeeze it back.
Okay. If you know how to fix this, you probably don't have a problem getting your clay off center.
Okay. That's true. Yeah. Well, and I have a tendency to open and pull it off center.
Is that just... People are just rushed. You don't give the clay time
to respond to whatever the pressure. You want the clay to go that way, but it didn't leave
clay enough time. You try to close it. You don't give the clay time to gather together. You push
it so the clay kind of gets the wrinkles. I saw someone that wanted to close the rim,
and then they just rushed, and then you get wrinkles. You have to do it slowly.
Give the clay time to respond to whatever the pressure you want the clay to go.
So if you see the social media, people are doing like making larger thing in one minute.
That's not true. Usually that speed of wheel is much slower, right? So you see that now the base
is wider, and you can start with a smaller base, but when you push it down, you push that corner
so you can actually push far out if you wanted to, right? Now the base is here. You found out
the base to be here. You can just keep on pushing, dragging the clay.
Well, the pin is fine because you're going to just wire it.
Drop into the pin? Yeah, because you are wiring it out, right? You wired it out so
you could clean up the hole, clean up your pin later. I see that now. It was like here,
and now I push it, so the base is a bit wider. It's close to somewhere between eight and nine
inches. Yeah, if you want to make it wider, you can make it as wide as you want it to,
but here, this part here, you see that? Yes. It's a little bit bumpy, so you have to
redistribute the clay here on the top. You spray the clay outward, and I'm using my fingertip.
I personally don't like to use a sponge because, see that? If you use a fingertip,
it's less contact point. It's less friction, so you see that when I pull, I lift. I just
use the tip of my thumb. The contact point is smaller, so it's less friction. Less friction,
you don't need to add a lot of lubrication or water. When you're adding too much water,
you're making the wall weak, so that's why I use the finger instead of a sponge. Especially
people, when you're using a sponge, you have to dip it in the water, so that water in the
sponge transfers into your clay, so you're weakening your clay. For the wider base or
platter, you want to make sure that you compress enough, so you don't end up with getting an
S-crack compressed. Now you can pull the wall, lift this part here, pull it up,
clean up. The very center point, I told you that if you are using the thinner metal rib,
don't go over, so a quarter of an inch away from it. If you want to take care of the center point,
you can do this first. You clean up the very center, and then a quarter inch away from it.
Outside, if you want to do a more curve, you can bend your rib, push that wall against it,
push the clay wall against the rib, and then the rib will take care of that,
making it nice and smooth. Lift this up, or if you want to change the shape,
a little bit of support here on the inner part. If that is a little bit wobbly,
chop it off, but for making something that is wider, a bit of a soft clay will be easier.
You can move the clay, because you don't need to fight with the gravity. All you need to do is
just make it wider, so for making something that is wider, you can use the clay a little bit softer.
Okay, and again, just chop off the corner. Use the skirt trimmer, or you can use the wooden knife.
Let me use a wooden knife this time. With the knife, just hold it like this, angle,
and then I just pierce it down until you touch. I can cut a bit more here if I wanted to.
Chop it down a bit more. The key is hold your tool steady on the same angle. People like moving
up and down, so sometimes you are not cutting it nice and smooth. You have to hold it steady, and
just go until you touch your bed. Then I just get a thinner knife, and you can
cut it off easily. Just clean this up before I cut it open. Let me finish it up.
That is the section view of the ball, wider baseball. Usually, I would recommend you trim
two foot rims, one on the outer part, and one smaller one on the inner part, so you have more
support. Otherwise, if your base is too thin, it will sag during the fire. One other way to do it
is that I do one foot rim here on the very center. I have a little pointy on the very center, so you
have support on the very center. Well, here, usually I will do my trimming here, so one foot
rim here, and maybe up to here, another foot rim, two foot rims, so that you have support. It doesn't
matter how wide your inner foot rim is, as long as you have support. Even if it's just pointy,
it's also okay, too. It could be wider, could be shorter, could be narrow, could be wider.