894. Complete Guide to Trimming with Hsin-Chuen Lin Part IV~ Chattering Technique

Hsinchuen Lin
205 followers
392 Video Views·May 2, 2026
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
Since you don't have the tungsten carbide, I'm going to use just the regular tool to do the
turning. First, I would lightly remove the clay from the side to push it. And you see that the
way when I'm grabbing the tool, what do I do? Do I hold the tool this way? No, right? Because you
want to hold it to grease it. So I hold here and then one finger to hold it there so it's firmer
and the tool is not vibrating. And then even I put one of my hand here so my other thumb is
also bracing the tool. So instead the whole position, rest here, rest here, and I can push
the clay in here. So that's how I remove the clay from the side. And make sure that the tool is,
when it comes to here, the sharper edge is cutting the clay, right? And if you have trimmed this,
you wouldn't hold your tool this way, right? You have to hold the tool this way, right? This
is the blade, the sharp blade, so you're going to use the sharp blade to cut it. So you have to turn
the tool this way to remove from the side, right? And you can go up and down, up and down. At the
beginning, when the clay is thicker, you can go and push it harder. You can remove a big
amount of clay like here, you push harder, right? But then your surface is not going to be as nice
as clean. So if you don't have your surface nice and clean, move the tool slowly, right? Move the
tool slowly. If you don't speed up, you can speed up the wheel, okay? Speed up the wheel. Let the
wheel do the job. But the hand motion is always slow, slow motion to do that, right? So that's
cutting the side. And then the clay in the middle, hold it from the side, I hold the tool this way,
this way, right? But here, it's harder for my hand to hold it. So I hold it more like holding the
here, and then slide it until you use one corner to remove the clay and push the tool toward the
side. See that? Always finding some way to brace it on. And here, on the side, what do you do?
You're not going to use this side to bump it into, right? What do you do? Get the sharper corner,
sharper knife to, so you turn the tool this way, and you remove the clay from the side.
That's how you do it. And then you keep on going, right? We have the thickness in mind, right?
Our goal is cut it into like nine millimeters deep, right? So if you are not sure how much clay
we can remove, go back here and then we check it. Now it's five, right? So we have four more to go.
Check it again. Usually for people who have been doing the pottery for years, they don't need to
do that, okay? But for beginner, you probably, when you are at the learning stage, you should
do that, okay? Check it. And now it's about eight. Okay, so one more. So that one more millimeters,
I continue to try to refine it. And also here, once you find out that is the right thickness,
you can knock it. Okay, that is the sound. You memorize it. Now it's like four millimeters,
right? So it sounds like that. And then we cut it three millimeters and you knock.
Later on, you memorize the sound, so you don't need to depend on the tool.
And you could just knock it. You know when to stop. All right, so now let's clean it up,
right? So I will stop right here. This is about four millimeters in here. If I want to do a bit
of chattering, chattering. So that is the chattering look like, okay? A little bit of
bouncing. Okay, that is so-called chattering. It's on purpose chattering. Sometimes if you are not
holding your tool correctly, you get unwanted chattering. But for the on-purpose chattering,
sometimes it's very, very beautiful. Let me do on-purpose chattering here, since I haven't taken
care of this part here yet. Smooth surface. And also here, you can use a metal rip to kind of,
we call burnish. Make the surface smooth, okay? You can push it, okay? So that is called burnish,
and you can burnish here too. Let me do the chattering, okay? This tool, I designed it
for chattering. I hold it, not lightly. I hold it firmly, but at a certain angle.
Okay, so that tool, it's jumping up and down, up and down. And then you can trigger the
controllable padded end, which looks nice. That's called on-purpose chattering.
The chattering tool looks very similar to the Asian trimming. Is it similar?
Yeah, it's similar. It's Asian style, but personally, I designed it for chattering.
This is for chattering. So this part here is lower, and this is more flexible. You want this
to be flexible. Okay, so it bounces. Yeah, so it bounces. Okay, so that is the chattering tool.
Of course, you can use all the tools to do the chattering, okay? If you know how. Okay, let me
show you a different tool to chatter. As long as your tool is sharp enough. Okay, let me use the
loop tool. This tool is not very sharp, but I have a very sharp tool, and I can show you the chattering
Okay, so that is also the chattering, right? Chattering is that when you do the chattering,
you need to know when the clay drags, and then hold the tool at a certain pressure, okay,
and you can manipulate the chattering. So that is called chattering.
So the play is kind of bouncing up and down. You're using the full face or just the corner?
Just the whole face. But the key is, first, that is the different story of a chattering.
The chattering is the whole lesson, okay? Your tool has to be very sharp, okay? And then at a
certain angle, the clay pushes back your tool, and then you speed up. You see that when I'm
chattering, I speed up the wheel. Is tungsten carbide a better material for chattering? No,
no. Sharp tool. As long as it's sharp. As long as the tool is sharp. The springy L-shaped one is
pretty good. Yeah, the L-shape is specifically designed for chattering. So can you do it all
the way? Well, if I want to do all the way, probably I wouldn't use the clay to hold it.
I use the water, okay? The clay holding, usually you do, the beginner, you use the clay to hold it.
But actually there are a couple ways to hold your clay position, and this is a very common way for
the people who are more professional. They use water. Water or slip, okay? Water or slip.
But when you want to do so, use the water or slip, you have to learn the tap centering.
Otherwise, when you're using the water, your clay is going to stick on here. It's very super hard
for you to move it, okay? So tap centering, you can still move the clay. And then after you
center, all you need to do is the down pressure, and your clay is holding in position, right?
And then if you want to trim, you want to chatter it all the way,
this tool is harder because it's not super sharp, okay? So you see that? It didn't
create that chattering mark like that one on top. But if you use it, it gets very sharp.
Do you recommend just sharpening it right before you use it? Yes, I recommend you sharpen it before.
First, I take care of that on the side.
So this side is good, and then I'm using this other corner, and then take care of that.
So you have a better, sharper corner here. Yeah, so that's how I do.
I told you that I could use all the tools to do all my trimming, right? It's not only the
this. All the tools are the same as long as you know how, right? Yeah. Now I remove
that chattering mark. There's no chattering mark here. Do you usually chatter under here? No.
I just want to show you if you do a little bit of decoration. That's an interesting aesthetic.
I like that. You like that? Yeah, I've never seen that. You could do that, or you choose not to do
that, and then you can just remove it, right? So you remove it. So you can manipulate it if you
want to chatter or you don't, okay? There's a certain way to do the chattering mark.
Is that possible? Deep? What do you mean deep? So you know how this is like shallow?
Can you make it? You can make it deeper. Use the clay a little bit softer and push harder.
You can make it. How do you know how far you go in on the sides? Because I know you tapped on the
bottom. Can you tap on the bottom? Yes. So that is one other that I haven't told you about. So you got this part
here, right? Good. And then you are going to compare this corner and this corner,
right? At least the same level. If you have more clay here, meaning you leave too much clay here,
you need to remove it. So usually we throw something on the inner part, we have a
slightly curve. So actually this part here could be even slightly lower than this corner, right? So
that's how I decided how much clay to remove from here. Speaking of going deeper, so push harder.
I haven't got the chattering mark yet. Okay, so you could get it deeper right here. See that?
This part here is deeper, okay? So you are more interested in the chattering, huh?
You could do it anytime you wanted to.
I can do it now. You can do it right now, right here, right? So I'm going to put a different
chattering mark here. Okay, so that is the chattering. And now this part here is good,
and this part here isn't, right? So that very last stage, you just clean up. Once you have a
reference, you don't need a reference anymore, you can start to clean up the foot at the very
final stage. This tool is a little bit dull. Got a slightly angle here.
Do you ever use the sponge to clean out at the end? The sponge? Yeah, you could use a sponge to
clean out at the very end. But here, usually I don't use a sponge. I just get a rock to
burnish it. Burnish, burnish. Any smooth rock, any metal, right?
Yeah, you could use the wooden tool, but the metal or rock is better because you are
pressing that clay in, make it more compact. And the smoother surface, the better that
the burnish mark or the burnish. So that's good. And then let me take care of that corner a bit
here. Do you undercut a little? Yeah, I undercut a little. So when sometimes when I'm dipping in
the glaze, that undercut can stop the glaze from going all the way here. Because usually I have,
I like to have my foot slightly taller. So when I'm glazing, I have some way to grab on it.
And I don't usually glaze here. Usually I have a smaller stem and then I just step right on the
foot. Okay, so that is the chair terrain. And also, I forgot to tell you about the way you hold
the tool, right? So a lot of people, when they are cutting the clay, they hold the tool this way,
which is not the right way to cut through. Why? Because when you're holding the tool this way,
you kind of like going vertical, perpendicular. It's like scraping, right? You have this tool
and then you do that, you're scraping. So you're going to end up with a rougher surface. When you
scrape, your surface is rougher, okay? And also when you scrap, it's easy to trigger the vibration.
That's why it causes the unwanted chatter, okay? So how do you hold the tool? This is 90 degrees,
right? When you cut it, slightly tilt it that way. So it's like you are shaving it up instead of
you scraping it up, okay? It's like, always think about you peeling the skin of the apple. You don't
peel the skin like this, right? You always cut like that. The same thing. If you peel that,
you could never get your skin of an apple to look nice, right? You have to cut it this way.
The same thing here. When you hold the tool like that, you're scraping it. Slightly tilt it,
right? And then you can use a different part. You see that? This is a versatile tool. You have a
curved, curved, and straight. So depending on what spot you want to use it, at the beginning,
maybe you can use more of the curved part. You can remove more clay. But when you want to get
it more flat, the last stage, you get a straight edge. And then speed up your wheel and then
move your hands slowly. So you can, you can get the surface nicer. And also here, when
you are cutting it, scrape, right? If you do that, actually, you are going to use the back,
the back of your blade. Actually, you are burnishing using the back of the blade.
So your surface will be much smoother, okay? Instead of you peeling it up, you scrape it up,
and your surface is rough, okay? So that's the other way. When you are doing it, slightly tilt it,
firm up, get closer and closer, so your tool is much stable, so that you don't end up with
having too much of the vibration. But if you're going to do the unpurposed challenge, I don't
know if you know this or not, when I'm holding the tool, I hold it a little further away, right?
And let the tool bounce. So that's, you want to, unpurposed chattering, hold it further away,
speed up, and then let the tool vibrate. If you don't want to chattering, closer, closer, please,
to avoid the unwanted chattering. If you find out the unwanted chattering happening,
change the spot of the tool when you are cutting it, right? The tool has so much spot touching the
surface. Maybe just a smaller spot, you will avoid the unwanted chattering, okay? So that is the,
and then the trimming process. And then for the water, all you need to do is hold it,
right? And then twist it, and you can remove it. That is the,
and it's even weight, not too heavy on the bottom, see that? Not too heavy on the bottom,
not too heavy on the top. It's balanced, right? You can pass it around. And everybody check it,
let me cut it open. All right. Oh, it's a trimming demonstration. I want to
see the thickness of the bottom, right? Yeah, that's the sound, you tap on it, and that's the
sound. So memorize. Sometimes the different softness of a clay always sounds different,
different too, so, and different diameter sounds different. So you have to learn every aspect of
different shape, different weight, different clay body, different softness to learn that,
okay? I didn't even trim the rim. The rim is a little bit thicker. I was going to ask if you
trimmed the rim. Yeah, you could trim the rim. Do you do that when you stick it on the bottom?
You can flip it over, or you can, you see that I was using the water so I can get all the way
on the very, very rim to trim, to finish it up. So far you have any questions about trimming?
Trimming is also fun too, right? Yeah, so just make sure you get your clay to have a very good
center, and you could sharp tools, good center. So you have to make sure that the rim is very
balanced, right? Yes, so, so yeah, that's why, that's why I show you before you remove it,
always level your rim before you remove from your wheel, okay? Is there any way to double
check that it's actually level? If not, you can start to trim, right? You put it right side up,
and then check it. If not, you can always slightly remove it, okay? And if your clay is not,
you forgot to level, level the top, actually there's a way to do it. So if your piece is not in
a good level, right, so if your piece is not in level, you can try to balance it. Put the clay
underneath, put this on top of it, so put the clay underneath to find your center. Yeah, bubble,
you put it, put it in right there, so you find your level first. Just put the clay, right? And
once you level it, and then you center it, okay? So that's the other way to do it, okay? Yeah,
I'm an engineer, so I find a way to solve the problem. Do you have a hint for how to trim,
from the bottom of a distorted piece? Sometimes I also have distorted pieces,
and so it's kind of distorted. Distorted? Yeah. That one?
Well, distorted pieces, usually it's not a perfect round, so you just hand trim it.
And for hand trimming, I don't know if you know about, this is a very good tool.
This tool? Yeah, so you just hand trim it. Yeah, that's a replacement blade for one of those.
Yeah, this is called a surfoam, s-u-r-f-o-a-m. There's a handle on it, but personally I like
the surfoam, s-u-r-f-o-a-m, yeah. Right, so that is how we are talking about
leaving three, four millimeters, and then compare the outer part and the inner part,
so you get to get the right thickness all the way evenly. And I told you that I didn't trim
the rim, so the rim is a little bit thicker, which is also good too, because it's holding
the sheet much better when you're doing the fire, that the thicker rim doesn't warp.
