Re-Repairing this Big Beautiful Hermle Clock On The Wall....

Amateur Repair Time
257 followers
702 Video Views·May 17, 2026
This is part 1, from about 3 years ago! https://www.youtube.com/watch?v=J8SfLVSV2vw
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time. I've been working on a bunch of
clocks. You can hear a bunch of them clicking and clocking behind us here. And one of the first
clocks that we did here on the channel was this big one and I think the video I called it like
let's work on this big huge ugly clock. It's much prettier now than it was whenever we started
working on it. I did a video where basically I did cosmetic stuff to it. So I stained it and I
cleaned it up and we put that artwork on the glass down there and we just got it all together.
We've been having a problem with it though and I noticed the problem when I messed with it before
but it's time to address it. So that's what we're going to do in this video.
Oh I think there was a piece of glass broken. I put a piece of glass in it too.
So the problem is the movement in it. We didn't do a thing to
this movement. It almost looks like a cuckoo clock movement but the thing was filthy. It's
been working fine but it doesn't have hardly any amplitude. So let me get a little closer
and you can hear it clicking and clocking. Maybe. Maybe you can hear that. It needs a little help
and there is a plastic gear on the front of the movement that I noticed whenever we were
working with it that's all stripped out and screwed up. This thing was abused. If you watch
that video this thing was just left in the dirt. It was in really bad shape. So at the time I didn't
really like it all that much but I worked on it and it was just the next thing to work on.
But I've kind of grown to like it hanging on the wall because the thing just will not give up on
working. It keeps working. It works just fine. But because of that plastic gear it won't hold
the hour hand on right so the hour hand doesn't turn. So it's broken right now. It's working in
a minute hand works but the hour hand doesn't. You can hear all the clocks in the background
going into alarm. Is it alarm? Warning I think. They're about to strike here in a few minutes.
So what I want to do is I think I'm just going to leave it on the wall and we'll just or maybe
I'll pull it off the wall. I don't know. We'll see. But I just want to take the movement out,
clean the movement, figure out what that little piece is and then order the replacement piece.
I believe it may be a Hermley movement which if it is that changes the whole scenario because
Hermley is a respectable movement you know considering the age of it. If it's a Hermley
movement I think I can get that part and I believe they even make a reproduction
brass part so we can get rid of that plastic gear and put a respectable
respectable brass one on there or maybe we just find a plastic one or maybe I've got one here at
house. But I've worked on several more movements since then and I feel pretty confident that I can
disassemble that one, clean it, maybe even put bushings in it if it needs it and put it all back
together and maybe after cleaning it we'll get the amplitude up a little bit. It's just see how the
pendulum just barely moves. It keeps decent time but it well that needs adjusted a little bit too
but it's a 31 day clock as well so it runs for quite a while and it's just ticking away
if you keep it level on the wall. So I'd like to move pull that movement out and work through it a
little bit and see if we can order whatever part we need or if I can look through my parts and see
if we've actually got that. So that's our goal for this video. Hopefully by the end of the video
we'll have it all back in there and it'll be working better than it is now. It's colossal.
It's ginormous. It might even be huge. Okay so like I said it works pretty good.
Yeah we put a new piece of glass in it and put some little
things to hold it in place. I guess I glued those in or put a little nail. Oh yeah there's a little
nail in them. That's pretty cool. So I'm going to take the hands off and remove the face and we'll
see if we can get the movement out of there. So that's it without the face on it. Here is the
movement. We'll pull it out here in a minute. The reason I was saying it looked like a cuckoo
clock movement was because the black pieces of the movement to me always just make me think of
cuckoo clocks that I've seen but I haven't worked on that many cuckoo clocks. And this snail on the
front that's plastic, that's our problem. That's why the hour hand won't stay on there. But like
I said I think there's an upgrade for that. So we're going to figure it all out in this video.
So let me go ahead and remove the... All right so I removed the pin and then took the pendulum
later off and then with the snail turned just right there on this shaft there is a c-clip and
a washer or maybe that's an e-clip and a washer. I took those off which allowed me to get these two
gears off. So this one it's like a it's almost like abs plastic but it's just all chewed up
from the hand over the years and so the hand won't fit on it properly where it won't slip
around. Now you could bend the hand I guess couldn't you? I could just tighten that up. I
wonder if that would fix the whole problem. This thing is not a... Yeah see look there's our problem.
So I wonder if... I don't think it goes all the way down like that. It might but
I wonder if I could just tighten that up. You know at the time I guess I didn't know that you
could do that. But I'm wondering if I should replace this. It's pretty crappy. It did work
though. Everything was working and it doesn't actually look damaged other than what I was just
showing you. It does look screwed up. Yeah like the top's messed up. Let's see if there's a problem
with the minute hand as well. So the minute hand is square. So how in the world is that holding on
around? Oh it goes on here. Duh. Alright yeah so the minute hand actually is fine because it mounts
on the minute wheel of course. I should have known that. Okay let me try bending this and just see
and then we'll see if we can look these up and see what brass ones cost. Well I can get it on there
by bending it but the problem is that the shaft is thinner in the middle because of just the way that
it's moved over the years. Deteriorated. So if that hour hand goes down too far it just gets
loose again where it's sloppy. This thing's kind of junky. This isn't a great, this movement's
pretty rough shape anyway. And then this gear goes under it. I don't know why they did that.
I mean I know they did it to save money but come on people. Come on we got to do a little better
than that. So this is a La Rose movement. You can see the rust here there and everywhere on it
but it does work good. It's a La Rose movement made in Germany, no adjustments, zero joules
and it's a 141-020. I'm pretty sure that is actually made by Hermley. It's a 72 which I think
is the year. It's a 1972 La Rose branded 151-020 which I think is a Hermley part number
and it's got a 101.9 inch well I don't know what that means 45 centimeter. I guess that's the drop
no I don't know what I don't know what that would be either. So yeah let me see if we can find these
and how much they cost because you know this clock isn't really worth a bunch but I would like to
get it where it works pretty well. All right so I did like any decent person would do and I went
and looked on eBay. I looked this up before but I just never took the time to take it all apart
and check it out. I found this guy. There's a bunch of people selling them one-offs so I've got like
for instance this $18. Looks like it's the correct set. It's a slightly different movement
number but just looking at them I think there's only two or three different types. The only
difference I see is in the length of the snout. This one looks like the exact one $52 though.
That's kind of expensive I think. We'll get rid of that and then this is another one $40.
A little steep for this clock. Now they can ask whatever they want for stuff you know.
This is the hour wheel it appears. Looks pretty good. This is a good set for 20 bucks
but then I found this guy. He's selling four sets with two different sizes which is
good. Three different sizes actually. This one is slightly different than these two. The
is the one we need. I think all the gears are the same. The hour wheel and then he's got three
sets of the plastic ones too. So worst case we can put another plastic one in there and then
four plastic gears. So he's got five brass. I'm calling it brass. I assume it's brass. Five brass
hour wheels. Or is that the minute wheel? Whatever. And then the four brass snails.
This is a $20 ship. So I'm definitely gonna buy this because then I'll have extras for next time
if I need them for anything else. So I'm gonna get this set. Alright so it's coming apart really
easy. So this strike hammer was down here in the bottom corner. Barrel number 21 was right here on
the left side. Be the time side. I mean the strike side. Barrel number 20 was the time side on this
side. Of course I let them down before I took them off. There is a center wheel here. There is a
second wheel here I guess. There is a... I think that's the governor wheel.
There is a... maybe that's the governor. The fly. This is the second wheel on this side I believe.
Got this bad boy. That looks like the escapement wheel. And this is
another strike wheel. You can tell the strike wheels from the time wheels if you haven't done
any of these. Because the strike wheels have accoutrements. See that little pin there?
So all of that is to make different things move. Make the flag move. Make the flag catch in the
warning. Make the hammer move. Whatever. So you can kind of tell if they're time striker... time
side or strike side by looking at that. One of our levers for strike side. And then there is the
back of the movement. I'm not going to take it down any further. It wouldn't get anywhere. So
I'm going to put this in the ultrasonic and clean it up. Now here's the front plate. I'm actually
going to put this in like this. I had a couple other movements that I took these all the way
apart when they didn't necessarily need it. And it's a pain pressing the stuff back on.
So there's gears pressed on. You can't just remove it. You either have to press that off
or press that off and then these off. I guess the way to go would be to take that off.
But then you got to worry about getting in the exact right spot and all that.
So if the bushing doesn't need replaced then this one's fine.
I'm just going to leave it. And then this one up here as well.
It's kind of held in place by this piece here that makes the
snail and everything work. The rack and snail work. So I'm going to leave that alone too.
So I'm going to put it in their hole in the ultrasonic and just have it clean up
as she is. But that's that. So we got it all disassembled. We found our parts that we needed
online. So I'm going to do a couple batches but I'll clean all this stuff in the ultrasonic and
we'll see how it looks after it's all nice and sparkly. Maybe. It's got a lot of rust.
We'll see what happens. All right. So I got everything out. I didn't completely
remove the springs. I just cleaned it in the barrel and then I dried it out as best I could
and I'm putting oil, new oil in it. They look really nice. No problems. And the other stuff
cleaned up pretty good. So let me lay it all out so we can look at what we've got and make
sure there's no problems with anything. So this is how everything came out of the ultrasonic.
I took these apart, dried them off, oiled them. This is the strike. This is the lever.
This is the piece and the screw that holds the gear on the top of the plate.
Here's how the plate ended up that I didn't take everything off of.
Here's how the time side gears look. Here's my strike side. And on this one, like I was saying
earlier, 20 is the time side and 21 is the strike side. I don't know how much difference it makes but
I'm sure it makes some difference. This is actually the, you know, the inside of this.
This is the outside. It looks a lot better than it did although, you know, it's got a little bit
of spotting and stuff on it. So the next thing I'm going to do is I'm going to take some toothpicks
and, you know, stake out the holes just to clean them out because a lot of times you get
kind of grease and dirt and oil stuck in the holes. So we need to clean out those
pivots just to make sure. The bushings. And then I'm going to look at them as I go through too.
I don't think any of them need rebushed. I don't think, it seems like this thing wasn't even ran
very much, you know. So who knows. But if I see anything that needs a new bushing, we'll put one
in it. It was working fine before. It just, the amplitude wasn't, it wasn't all that great and,
of course, our gear problem. They have shipped our gears. We just haven't got them yet. So I'm
going to go through and start cleaning these holes. And if I run into anything interesting,
I will let you know. Okay, so I put the whole thing back together. So a couple things that
I noticed about it. This, of course, is the rack that interacts with the snail. So
that mounts kind of like that. I've oiled everything. Oh, I polished all of the pinions
too. So like the way I do it is I take the wheel and squeeze some really fine sandpaper around it.
This is, it's silicon carbide and it is 2,000 grit. 2,000 grit. Just enough to, that's good
to polish, I think. So I polished all of the pivots. I can't find any wear on anything. I
think the thing was never ran. I think it just, maybe they used it for a little while and it just
sat around. I think it was just filthy and had grease and oil all over it. But it, I don't think
they ever used it. And when it was hanging on the wall, it was working great. So that's that.
So there's that. These little wheels, they both wind the same direction and you can only put
them on one way for them to catch with the catch, with the click. So they're actually both exactly
the same. These posts are also both exactly the same. The two C-clips are also both exactly the
same. So that's good. It looks like it was just a very well-designed little movement where they
were trying to figure out how to make things work well. It's got little springs built into the
movement that you just kind of loop into place. This top one just hangs down to push back down on
this whenever it gets lifted up. So that essentially, when the minute wheel spins around,
this little thing is going to push up on that so that it grabs the governor wheel, I think it's
down. That spring helps it goes back down. Whenever it falls back down, it's going to
allow the fly loose so that it can spin and then boom. All right. So there's a little lever over
here where there's a little wheel there that as it spins, that little black piece
slaps this lever a little bit. And the lever, well, it's got another spring there on the
post to give it a little bit of tension. And whenever this moves out, it is
captive in this hammer here. And so it will move the whole assembly that way,
moves it back a little bit and then releases it and boom. And then the snail will fall down
again and again and again. And so this little blade here is what rides on the snail.
So if it's 12 o'clock, it will only fall one position before it has to stop because the
snail stops it. Or if it's one o'clock, I mean. But if it's three o'clock, so this is reset,
it all does its thing and it falls one position. Or how does it work? One position. That's one
o'clock. Now it's gone to two o'clock. Now three o'clock. And it can't go any farther, right?
So depending on where this little seashell or snail is, this bar can go down farther. And so
each time it lets it, as this turns, it allows it to drop one position. I don't know if I can
show you that, but basically this will turn like so and then it gets stopped. And then if it's
lifted back up, it gets to the point where it can turn some more. And it just, we'll see it whenever
we get the new one in, but it basically walks this through however many times this allows it
to. And then at some point this gets reset and then it does it again and again and again. So
each hour, as this turns, you get more and more time, right? You kind of have to set this right
as well because the distance from here to here is different than the distance from there to there.
It kind of falls at an angle, but you kind of have to, you got to play with it a little bit.
It really should land right near the front. When this falls, this shell should be right near the
front when you're on the hour because you don't want it to, at the end, instead of landing in
there, for it to land up there. You know what I mean? So like it has to be, there's a little bit
of a timing to it. It is a clock. If you get where it's not striking right, it's because this thing
needs to be turned a couple teeth or something to get it just right. It's something to look at after
we get it all back together. So we got to wait for our parts. I oiled everything. I just put one
little teeny tiny, the smallest drop I could on anything that moves, all of the pivots. You don't
want to put a bunch and make a big mess, but it's all oiled. Everything's waiting. I'll put the
suspension rod or the, what is it? What's it called? The pendulum suspension. It is called
a suspension rod, isn't it? I'll put it on whenever we get the new stuff in, but basically
I'm just going to get those in and find whichever one is an exact match to this or very close,
and then we'll be ready to put it back in the cabinet. I got them in. I was so excited that
I got them in. They're all too small, every one of them. The gear, right? So these that I got,
they match the other ones that were for sale on eBay, but they don't match mine. I don't,
my gear is bigger and it has to mesh with this. So it's got to be bigger. There's no way around it.
And then this gear is bigger as well. So not quite. So I ordered the wrong parts,
but I'll keep those and maybe I can make this, this idea work on another one, but I guess we're
going to have to go back to how we had it. So instead of fixing this hour wheel, we're just
going to have to make it work. So the problem was this was pushed in so far that it's loose,
but if I keep it up near the end of the thing, now that I've tightened it up, it'll stay on there.
It's just, you know, I wish it was in a little better shape, but we'll just have to make that
work again. Okay. So let me put that back together. And then there's something on the
that I've been wanting to fix too. And then we can hang it back on the wall and see how she runs.
Okay. So the clock's been hanging up there for quite a while, a couple of years,
and it hangs crooked. So it's, it's, I think it's because this is too long.
So it just, it's so loose that it lets it hang, you know, that far off the wall. And then the
bottom sits on the wall. So it's, it's hanging like this the whole time. And what that does is
it lets the pendulum hang forward and it's really close to rubbing on the face. So I'm going to try
to fix it. So I'm going to shorten the wire. And after I do that, I'm going to lower the nail,
the screw that's holding it in so that we get back about where we were. And I'm going to take
this little scrap piece of wood I have and attach it on the bottom. And that should keep it,
the bottom sitting off the wall a little bit, and then the top is going to be off the wall
a little bit. And that should make it pretty, pretty even. So that's my plan. So it strikes
a little after the hour. It's got a kind of, you know, this wasn't a top notch clock back in the
day, but it's good to get it working a little better. And it's got a, you know, it doesn't have
a huge amplitude. I don't even know if it's any better than it was, but at least now I know the
movement's all clean. And I'm going to keep my eye on eBay and see if I can find a collection
of bigger snails so that our hand will fit on there a little better, but it's working pretty
good. If you, you can adjust it a little bit, like it's a little off, you know, it should be
a little forward. And then there's a, there's a slight adjustment you can make inside the movement
so that it hits right on the hour, but I'm not too concerned about it. So there you go, folks,
a little bit of work on this big old clock. We'll probably have to work on it again if we get one
of those snails in, but hopefully it will run well. So I'm going to leave it wound up and see
what kind of, see what kind of action I get out of it. So I need to see after it's cleaned,
that will change how it keeps time. Like it might be faster or slower than it was before. So I might
have to adjust that out. So I'm gonna leave it run for a month or so and we'll go from there.
So I hope you enjoyed it. Leave your comments down below and I will see you next week.
