Antique Clock Restoration - The Complete Job - Part 7, Completing the work.

Chrono Chronicles
8 followers
2 Video Views·Apr 21, 2026
I removed the thick chrome plating, restored the wax infill, re-grained the dial and then
re-silvered and waxed with micro-crystalline wax to protect it.
The next stage of the restoration is to rebuild the movement and put everything back together
again into a clock.
The first stage of this is for me to refit the mainsprings into the barrels.
The mainsprings have been cleaned and then I have a process that I like to use to lubricate
the springs.
I've tried many different things over the years to different methods of lubricating
the springs but what I've come down on now that I use mainly is to firstly spray the
Then I wipe most of this off again after I've wound the spring into the winder like this.
You can just see the sort of wet PTFE just oozing itself out of the cause of the spring
in this shot.
Then when the spring is wound up into the holder I can then oil it with a slide-way
lubricant that I use.
It's a high-pressure lathe slide-way lubricant and it is designed to be in high-friction
sliding applications on a lathe slide-way so I thought this would be an ideal lubricant
to use on a mainspring.
So far I've found that over the years I've been using it I've found that it's severely
reduced or drastically reduced the clunking and slip-sticking effect of grease on mainsprings
and it seems to be a much more efficient lubricant to use and makes the spring quieter in the
barrel.
Once the spring is in the barrel I then add a small amount, well a generous amount actually
of lubrication to the pivot so that I can wind the spring in without risk of galling
the nice new bushing that is in the barrel by winding it with the pivot drive.
And removing the holder from the spring is hopefully a straightforward task.
Not always, sometimes this can be a little bit problematic if the spring doesn't want
to hook up nicely but on this occasion it worked out very nicely.
And I could unwind the spring back into the barrel so it's now safely captive in the barrel.
And I always like to wind it a few times at this stage so that it sort of moves all the
oil around a little bit.
And then I'll oil it again from the top side of the spring so it's got the slide-way oil
from both top and bottom sides.
This means that I can be sure that the oil is sort of working its way into the spring
from both sides.
It often takes a small amount of time for the oil to work everywhere so sometimes when
the clock's on test the first couple of winds it might clunk a little bit but it tends to
settle down as the oil moves around the barrel.
Again, oiling the pivots first.
I'm using the red coloured oil, it's HP 1300 for those who are interested.
It's a high pressure, very high quality synthetic oil that I use for the large end of the train
if you like, for the heavy applications.
It's important to make sure that the barrel cap goes down nice and tight but so that it's
flat.
If it's not sitting down flat then it can cause the barrel arbor to grip at an angle
so it's important just to make sure that that is down flat and to check that it's got end
shape.
End shape is a really important factor in any mechanism with pivots basically.
It has to have a certain amount of movement end to end, end float movement in order to
run freely.
This is a very important stage that I like to carry out.
I hold the spring barrel and then I wind the spring up fully and then whilst letting it
run down I make sure I've got end shape all the way through the wind.
This ensures that the spring is not angling over and dragging on the barrel bottom or
barrel cap and killing off the end shape because this can severely reduce power.
With the spring back in the barrels it's time to brush off the dust residue from drying
in grit cobs.
All of these parts have been treated with microcrystalline wax and I like to just make
sure there's no residues of anything, any dust and any residues from the wax still
on the parts.
The best way I've found of doing this is just to give everything a last brush off before
putting it back together again.
You can see here the importance of double checking that all of the grit cobs are gone
from the parts.
Grit cobs are a media that's used in the drying process so it dries off the white spirit
that I use to rinse the parts in by wicking the liquid away into the cork media that helps
it dry.
The pegging stage is absolutely critical and you can't spend too long on this.
If you leave any form of debris or dirt of any description in the pivot holes and then
put the plot together and oil it, the oil is just going to pick up that dirt and discolour
depressingly quickly so it's best to spend as long a time as you think fit pegging out
all the holes.
I dipped the pegwood in a small amount of isopropanol alcohol and then this is my final
stage is to then peg the holes out a final time with the wet pegwood from dipping it
in isopropanol.
When putting the fuses together I have to ensure that the clicks, the pawls if you like,
are sprung correctly so that the spring is pushing it all the way down.
As you can see it stops up against the inside of the grate wheel but it's important that
it's sprung all the way.
If it has any kind of freedom to float around without the click spring pushing it all the
way back then that could cause an occasion where it could slip on the ratchet wheel and
that would be disastrous.
The line I'm using on this block is a synthetic line.
I do often use a harp string which is a natural gut on high quality clocks.
This is a nice quality clock but on this occasion it was perfectly sufficient to use this synthetic
line.
It is not going to damage the clock in any way and it's a much cheaper alternative to
the harp string line.
A good secure knot is really important because if this knot was to fail that's game over
for the running of the clock and it could mean damage to the grate wheel and the associated
pinion.
I'm putting the ratchet wheel back onto the bottom of the grate wheel.
I made a little mistake here by picking up the wrong screw but luckily I noticed my mistake.
I noticed that it was just standing a little bit proud and it's always important to check
for things like this because if that screw was left like that that would have caused
the tightness in the grate wheel and really chewed up the inside of the grate wheel when
winding the clock.
It's important to keep your wits about you even if you think you've got all the right
screws in the right place.
Just double check yourself and make sure that everything is doing what it's supposed to
be doing and not doing anything that it shouldn't be doing.
I wind a full fuse's worth of line on and then tape it up.
I always make sure I lubricate the areas that are wearing when the clock is being wound.
Now these parts are only moving when the clock is being wound so a lot of the time they get
missed, they just don't get oiled.
It's nice to maintain a nice feel when you're winding the clock.
You don't want it to feel rough and tight and also you don't want anything to wear when
it doesn't need to wear so it's good to make sure that all of these parts are correctly
lubricated.
One of those parts is the pivot that goes through the grate wheel itself.
Again, this is only ever rotating when wound but it's good to have it properly lubricated.
And then obviously the face of the ratchet ball clip needs to be lubricated as it runs
into the ratchet wheel.
And then this point here is to lubricate the face of the fuse where it wears against the
grate wheel when being wound.
This often gets missed.
Again, not just somewhere that is necessary in order for the clock to run but again it
is a wear area that when winding the clock it's good to make sure that it is lubricated
there.
In the previous video I made these spaces to make sure that the end shape of the, or
the column against the fuse was correct because it's important that the grate wheel doesn't
flap around because that can have effects on the depth thing or even with the grate
wheel catching other wheels further down the train.
So it's important just to make sure that the grate wheel is free to rotate so that it's
lubricated whilst winding and so that the ratchet can operate properly but it shouldn't
really flap around.
So I have to make sure that that tolerance is correct.
There comes to building up the sort of power end of the clock.
The mainsprings are obviously in the barrels and the line is wound onto the fuses.
The other end of the line comes around and is knotted into the barrel to link the two
parts of the power part of the mechanism together.
The next stage after assembling the movement is to check that the strike is all set up
properly.
I'm looking here for the hammer to rest there not being on a pin.
So it's just dropped off a pin and is resting nicely.
So it's not going to risk being, lifting on the warning and it's not going to hold the
hammer at the end.
Also I need to check that the warn is of a suitable amount so that it doesn't lift the
train on.
I then replace the rough taper pins that I used to assemble the clock with neater pins
that are all trimmed to length and nicely domed off at both ends.
I like to try and make the pins look as tidy as possible.
It's just a little bit of pride in work.
I hate seeing chewed up nasty tapered pins clipped off.
I like the pins to be neat and tidy and if possible nice and equal, pushed into both
sides of the pillar.
Now here this is a five pillar bracket clock and the central pillar, it's very important
that that pin is in tight when working on the clock, when doing the bushing work.
Because when you drive that home when assembling the clock now that can sometimes tighten up
the train.
So this stage now is to check that for about the tenth time during assembly, just that
everything is as it should be.
This is a particularly important stage to check that the end shakes are all present
on all the wheels for the train.
Now that I'm satisfied that the clock is set up properly I can spend the time running the
line onto the barrels.
There are other ways of doing this but on some clocks this is the only way is just to
let the train run it through.
Now a very important stage is to check that the strike train is able to run in all situations.
So you can see here I'm stopping the fly through the duration of the lift of the hammer to
make sure that it's still capable of picking up again.
So the train can restart itself in any situation.
That way I'm sure that it's not going to be in a position where it could stall.
And finally with the line set up on the barrel I relax the spring to the point where it's
just about to let the line move.
I don't actually want it to let the line move it's just enough to keep it on and then give
it the set up.
Now the amount of set up is different clock on clock and spring on spring but a good starting
point is about a quarter of a turn when the clock is completely wound down.
So with the clock assembled it's possible to see that the pendulum is quite sloppy on
the crutch.
The slot in the pendulum is very wide open.
This is actually a replacement pendulum you can see they've made a bit of a hatch of chopping
the slot open and then closing it up by bending it.
So what I'm doing is to chop some shim stock, some brass shim stock which I then want to
soft solder into the slot.
This is after opening the slot up slightly and straightening it all up.
So then with it all oversized I can file it down neatly.
I'm not too worried about this pendulum it's not original to the clock it's a fairly modern
replacement pendulum.
The pendulum has obviously been lost at some stage in this clock's life.
So I'm not too worried about invasive work on this component.
I would perhaps be a little bit gentler on how invasive I was being with an original
component.
So then with the brass shim stock trimmed down to the thickness of the pendulum rod
I can then open up the slot and file it to a nice parallel smooth slot.
Before checking to see how the tolerance is with the crutch pin.
Now this is a trial and error method I mean you could do it with measurement but if you
try and measure this and work to a dimension you're almost certainly going to overshoot.
So it's the kind of thing where there's a lot in clockmaking that has to be done by
feel.
Clockmaking is a trade that's been worked on by touch.
So when I was closing in on it it's just very small amounts that are needed from this stage
just to finish it off and get it to the right size.
The slot is then cleaned up and burnished to give it a nice smooth surface.
The crutch itself was running in great condition and was slipping far too freely.
It had already been beaten up quite a few times so it was difficult to tighten up.
So I wanted to make sure that the clock wasn't in a position where it could put itself out
and beat.
So what I did was to remove the crutch from the pallet arbor and then turn the pallet
arbor back a little bit, the collet for the crutch back a little bit.
And that enabled me to have a little bit of meat left on the collet to rib it over to
hold the crutch in position.
I put the crutch back together loosely in the clock and then for initial assembly I
just put some thread lock.
So this isn't the strongest lock type, this is a lock type that can move or can be made
to move.
And I just put a small amount on to hold the crutch in position.
After allowing that to bite and just enough to hold the crutch in position I then was
able to make the adjustments.
Now I need the adjustments to be pretty good before I rib it up to the end of the crutch.
I'm not going to rib it so that it's solid, I'm still going to have it so that it will
slip but not enough to slip easily under normal work.
Setting the clock in beat is a very important thing that needs to be done.
Clocks will sometimes run favouring one side of the beat but if you want to get optimal
performance out of the clock it's important to get it in beat.
And some clocks just won't work if they're not in beat.
Split anvils or split blocks are incredibly useful for jobs exactly like this where you
can't put the whole part straight through a hole in order to support it but you can
then build the support either side of it with the split anvil.
I wanted to make sure that the brass collet was peened over nicely but again not so hard
that it couldn't be moved.
This is where the lock type that I put on earlier came into its own to hold the whole
assembly in the adjustment that I just made.
Otherwise it would have slipped around all over the place and I'd have been starting
from square one trying to set the clock in beat.
With the dial now refitted the only thing that remains is to remove the pin holding
in the hand collet and to shorten it and dome off the ends.
It's always nice to complete the job with a decent looking pin right where you're going
to look at it the most on the front of the clock.
I hate seeing pins that are either left way too long, uneven or just snipped off messily
without taking this little bit of extra attention to detail and making a really nice job of
it.
It looks so much better.
It looks like some care has been made for the job.
Then it's back into the case with the movement.
