Day 652 - DIY Spray Foam Insulation, Apartment Build | Part 5

BPo3 Homestead
90 followers
Thank you, BEESTUSA FullStop, for working with us on this apartment build. Learn more about FullStop DIY spray foam insulation here:
(affiliate link)
👉👉👉 https://fullstopbeest.com/JONATHON16
#beest
Check out TimberKing for more info on my 1220CRZ sawmill, or one of many Made-In-The-USA fully hydraulic mills: https://timberking.com/product/timberking-1220-crz/
#homestead
AI Generated·May contain errors
PPO3 is supported by Timber King sawmills. For more information on my 1220 CRZ mill or one of many
Foley hydraulic options go to TimberKing.com. Insulation day is finally here. I've been
battling temperatures. The next couple days I'm going to be battling temperatures. So today is
the only window of opportunity to get this stuff done. At the very least the walls. I think I'm
going to do this in three stages. I'm going to do the walls today. I don't have the preparations
done for the ceiling to be completely confident to get the ceiling done today. So the ceiling
will be another day and then I still have to install the flooring in the bathroom and then
the tub and then the sink. And at that point I can wrap up the insulation job by insulating the
bottom of the bathroom floor because cold toes are no fun. The spray foam that I'm using is a DIY
kit from Beast USA. The kit itself is called full stop or the stuff that I'm spraying. This is a
full stop spray foam insulation. It's a DIY kit. As you can see it comes in cans. One or two or a
hundred or so cans depending on how much you're actually using. And this stuff is a closed cell
hybrid foam. The exterior dries to a nice closed cell finish but the inside is a hybrid
system on the inside. This is something that you can do yourself. Each kit comes with protective
PPE. You got a protective coverall, some gloves, safety glasses, and it does say wear a mask if
you are in a non-ventilated area. However I would probably recommend wearing a mask regardless if
it's ventilated or not. This space right here is not really that ventilated. I'm going to crack a
door over there and crack a door over there and put a fan exiting the air out in one of the directions.
But I'm also battling heat. These cans need to stay where is it 68 to 77 degrees Fahrenheit.
That's the sweet spot for getting these cans to perform optimally. And that's what I'm working
on right now or what I'm battling I should say. It is currently 73.9 degrees here inside this
apartment and the cans are anywhere from 76 to 74 over there. And then some of these in this can
or in this box are in the low 70s. So I need to make sure that the cans stay at an appropriate
temperature. To do that I've got a couple radiant oil heaters over here. Heat rises. It's hitting
that cardboard that I stapled or nailed to the box or to the studs right there. And it's pushing
all that heat underneath this table where I have it everything stored. Before I get going I do want
to document a bunch of stuff to to see the overall temperatures and whatnot. So this back wall and
it's reading 68 degrees. Now let's go to the opposite corner. This corner is sticking out
into the shop. 63.2. 63.2 on that wall and 62.7 on that wall. So we've got a bunch of heat
here in this apartment set up for me to actually do the spray foam. But we're not holding it in.
One big benefit of closed cell foam is it does not allow air to go through. So on this wall over here
I don't know if you can see it but there's a horizontal green line and that is where the top
of these eight foot panels terminate. And then the next panel above it that's where that that seam is
in between those two panels. This is not three quarter inch you know tongue and groove OSB. This
is 7 16th OSB with butt joints for all of the seams. And that's an air gap. So the closed cell
foam will stop air from going through there. As it is right now that's probably where I'm losing the
most amount of heat. Well probably radiating right through the walls too. But that's where any
type of draft is going to be leaving with hot air and then any gap along the floor like this one
right over here where I have an I-beam coming out just a little bit of bottom flange that I had to
put the sill plate up just a little bit to clear that flange. Cold air is probably coming in
through there. As the heat rises it's currently leaving in gaps like that. So all of that will be
stopped with closed cell foam. I'm going to take some temperature readings just to document today
and then outside the shop. And we'll actually see the light coming out of inside this space through
those gaps. If you're not familiar with this space well don't mind the mess. It's a continuous work
in progress. But this is a 40 by 60 metal building with a little bit of insulation. And that's the
apartment we're building. It's just two bedrooms and a bathroom. In the summer months when it's
nice and warm outside here in Mississippi that door stays open. That door basically always stays
open. That door stays open. All these windows stay open. So essentially this space is what I consider
shaded space. It's outside essentially. It's not heated and cooled at all winter or summer as it
is right now. And it's just open air. So what the apartment is, we have an advantage with this
because it's essentially an envelope inside of an envelope. So we don't have to contend with a bunch
of brutal wind hitting this side of this. So we do have that advantage. But the way that this is
in you know an envelope inside of an envelope we're going to see an even greater benefit in
heating and cooling costs. And I think this is going to be a super energy efficient space. Not
because of all the crazy stuff that we're going to do to inside here. Spray foam is going to help
tremendously. But the biggest advantage like I said that we have is it's an envelope inside of an
envelope. So this is not exposed to the brutal sun that we have here in Mississippi. And it's not
exposed to our very very windy winters. Outdoor thermometer says it is about 41 degrees Fahrenheit
outside. With no heating or cooling it's about 53 degrees Fahrenheit inside. A little asterisk about
the no heat inside the shop. I don't have any heaters running but my wife's doing laundry and
the dryer is just pumping hot air into this space. So there's that. I'll turn the lights off here in
the shop and leave the lights on inside the apartment. And you'll see light coming through
this gap quite a bit. Zoomed in a little bit and you can see you can see these big gaps right here.
So closing that off will definitely help.
So
so
First layer is done and boy I learned a lot that's for sure. The corners where I squirted a little
bit in there too thick. That stuff expands a lot. So oops it's all nice and hard to touch now.
So let that cure and whatnot. The first layer is the first half of the first layer is really thin.
I didn't even get coverage right there on the OSB. Really thin. I was trying to figure out my
spray pattern and trying to get it all done in one coat. One pass I should say.
But I don't think that's the best strategy actually because when I was finishing up up here
uh let me get over to this room. Up here I uh I overlapped it several times as I was spraying
thinner passes and I think that worked way better because that looks to be right about one inch
thick and some of my walls look to be like a quarter inch thick at some spots. So that's
something that I learned. Something else that I learned is I am right-handed. I didn't learn that
today but I'm right-handed. So as I'm spraying it's easier for me to get into the left side. So
the left side on the majority of my wall cavities here is thicker than the right side because I'm
coming in on the angle over here and I'm pretty much going in straight over here. So a little bit
a little bit of a technique dialing in. The slowest thing is stopping. Right? Stopping. What am I
stopping for? To move the camera and also to shake these cans and shake the cans and shake the cans
and shake the cans and shake the cans. I'm going to be sore in my elbows from shaking these cans.
So for the second layer I've got another respirator. Jamie's going to help me out behind the camera
shaking some cans and hopefully we can go a lot faster now that I've got a little bit of
experience doing this and get the second layer put on. It is a week and a few days later and I'm
so glad we we got the walls done in this apartment because I had to rush to get this done and get
temporarily moved in. Don't mind our mess. We have nails on the studs and stuff everywhere.
We're temporarily moved in to get out of the camper during this ice storm and snow and cold
weather that just hit hammered half of the country. Anyway that's a topic for another day but before
before we moved in temporarily moved in before we did the spray foam on the walls we had two 1500
watt radiant heaters. So these that's one of them right there an oil radiant heater 1500 watts
running wide open and the warmest we could get this space was a little over 70 degrees. I forget
the exact number a little over 70 degrees and that was with both heaters centrally located
funneling that hot air from the heaters to the bottom of that table to heat up the cans.
The perimeter of this space was very cold and drafty. One of the benefits of spray foam obviously
closed cell spray foam is it stops all drafts. So one thing that we noticed while being in here is
there's a much more even temperature all the way throughout this little apartment with no fans
going. We just have these like I said these radiant heaters and also 10 foot ceilings. These
wall walls are 10 foot and there is no ceiling just yet and there are some gaps in the ceiling
where this where the rim joists meet the top sill on the walls. You know you put the rim joists on
there crown up well crown up if there is a crown and then weight on top will flatten it out a
little bit. There's hardly any weight on top so we do have a gap on that wall over there that I tried
to temporarily seal off with duct tape didn't work didn't hold it kept falling down. I did the
same thing on this wall and it did temporarily hold but those two will be completely eliminated
when I do the spray foam on the ceilings. So that's again one of the benefits of the spray foam. Now
having completed this much of this this job here I learned a tremendous amount and I learned a
the thickness on one wall the rest of the walls I'm happy with but this particular wall
was one of the first walls in the two layers and when I was first spraying I don't know if it's
just used to the way I spray HVLP finishes on woodworking projects like a big table or something
but I was I was going way too fast. So the first quite a bit that I did I sprayed with a horizontal
fan pattern and moving in a vertical direction and I don't think that's the best for me anyway I did
not have the best results that way. I also I think had the gun a little bit too hot a little bit too
much pressure coming out of the can when pulling the trigger so there's a there's a screw on the
back side of the gun you screw it in you allow less less material to go through the through the
actual gun you back it out you allow that can to open up a little bit more and spray some material.
I think I had mine dialed out a little bit too far and as I went through the second layer
I dialed it back in and changed my technique and world of difference. So if I was to do this all
over again I would not go with a horizontal fan traveling in a vertical direction I would go with
a vertical fan traveling in smaller horizontal sweeps as I go through each one of these cavities
and when I switched over to that pattern it forced me to slow down and actually see what I
was doing a little bit more than rather than just trying to go for coverage it's not about coverage
it's about material buildup so that it expands out to that one inch thickness per layer of
application right. So I think my technique was a little bit bad on about half of this but this is
only wall that I'm not too satisfied with the amount that I built up. Now why did I add more
well we were trying to rush to get this done so we could kind of move in immediately during this
this ice storm if you know what I'm saying. So when I do the ceilings which is up next in the
next few days we're going to take everything back out of here put some tarps down or some drop
cloths or something and do the ceilings and when I do that I'm going to touch up that wall a little
bit more and add a little bit more material to that particular wall. I have I have the cans to
do it I just didn't build it up enough which is also leads me to another point. First impression
it it is a very slow acting foam now that's that could be personal preference or personal
observation there some people may say hey this foam expands super fast I don't know I think it
expands slowly so with that in mind on my second coat there was a few places where
especially the smaller cavities this this one right here in the corner kind of hard to show
you because I've got stuff in the way let me show you a different one that I sprayed on and then I
thought it's not not really expanding let me spray a little bit more that's not really expanding let
me spray a little bit more okay I don't want to overdo it so let me go away and do something else
and come back and see how much it expanded and holy smokes it expanded this cavity right here is
not that wide it's it's five or six inches wide right here and this is where I was talking about
I sprayed a bunch and sprayed a bunch and it's not really expanding sprayed a bunch not really
expanding so I go away and come back and holy moly this is all just waste this is just waste
waste I have to cut all this off when I put my interior siding on so keep in mind this stuff
may not expand as fast as you think it will but it sure does expand this is one of the guns that
came with the kit and you screw the can on from the top you activate it with this little or you
turn it on rather with this little knob and then the tips come with each one of the cans each one
of the cans comes with a blue tip for the walls and a black tip for the ceiling I will recommend
swapping out the tip with every single can and that might be in the instructions somewhere that
I couldn't find or whatever but I didn't do that I read in the instructions that if the if you're
not going to use this for 30 minutes then replace the tip the nozzle when you get back to spraying
so I thought well if I'm not going to use it for 30 minutes that sounds like you can keep using them
so in the beginning I used these for I think far too many cans and what happened is a little bit
of material will start to build up on the side of the spray gun and then a little bit more builds
up and then eventually you have a little bit becomes heavy enough to fall off and then you
have a glob falling off then you have a glob falling off and all that is is waste so on the
boards that I was kicking around on the floor if we're to catch the overspray and the the boxes
that I was doing that with the majority of the material that was on those boxes was just waste
from the from these nozzles until I started swapping out the nozzles with every can so swap
out the nozzle with every can by the way pulling these off if you just try and yank it off it's
it's doable but it's much harder than simply grabbing the gun and using your thumb to pop
it off way easier to pop it off like that especially if you've got goo on your gloves
or whatever so pop it off with your thumb put a new nozzle on every single can every can comes
with a brand new nozzle use them also this is the screw that I was talking about on the back
side of the gun I had it backed off I think way too far at the very beginning I sprayed it in a
box and I still thought it was good again maybe I was used to the way I spray my HVLP finishes but
this was way too powerful at first clearly at first I mean you see in the footage I was
the material was hitting the wall and then blowing right off due to the pressure coming
out of the gun from the can so there's that one final thing to note and that is about the smell
that this created it says to apply all this in a well-ventilated area obviously this isn't a
well-ventilated area especially when I'm trying to keep the door shut to keep the heat in so I wore
a respirator with an organic cartridge I couldn't smell anything I had no idea that this stuff
smelled until I was completely done outside of the apartment and took my respirator off and oh
that stuff's stinky so anyway I would recommend wearing a respirator no matter what even if it
is a well-ventilated area that's just that's just me that being said it off gassed quickly
there was a very very distinct smell of this stuff when it was curing but after 24 hours there was no
smell at all so we ventilated this we closed it in and let it just sit for 24 hours and then
afterwards we weren't worried about the temperature too much so we ventilated it with a
fan you couldn't hardly smell anything and then after a short period of the fan you can smell
anything so we've been in this space temporarily like I said for over a week now and there's no
indication of off gassing or of stinkiness or of headaches or anything crazy like that so
so yeah I still recommend wearing a mask that pretty much sums up the phase one of insulating
this apartment I still have to insulate the ceiling and I still have to insulate the floor
of the bathroom after I get all the plumbing done underneath there hopefully you've learned
from some of my mistakes and and your first go at this is a little bit better than mine
I was rushing to get this done and I'm so fortunate that our timeline worked out to where
I was able to actually we were able to actually move in to this halfway insulated apartment
rather than staying outside in our camper during all of this chaos so so yeah I'm very
very fortunate about that if you're interested in more about this product this is full stop
DIY spray foam from Beast USA I'll have a link down in the description from with more information
it's an affiliate link your price doesn't change if you use my link but I do get a little bit of
commission on the sale so there's that all that information down in the description and yeah thank
you to Beast USA for helping me out with this part of the project phase one down two and three
still to go you guys take care and I'll talk to you in the next video
