Hi, I'm Mike with House on the Mend, and in this video we're going to be reviewing the Black and
Decker 12-inch 40 volt cordless chainsaw, specifically the LCS 1240. So let's get started.
All right, so the unit I purchased was off of Amazon and it was refurbished, so it came in that
plain brown cardboard box that you saw, with nothing other than what you see here. No packaging,
cushioning, nothing, not even the manual. So I downloaded the manual online, which was pretty
easy, read through it, and here we go. Let's go through some of the nomenclature you see here.
First of all, we have up top the lock button. So you pull the lock button back and then you
squeeze the trigger control down here to start the saw. And this one, if you look right here,
came with a zip tie safety. So I'm going to take these little wire snips and I'm going to cut that
off. There we go. And now when we pull back the lock button, then the trigger switch works.
We have the front handguard, and unlike a gas-powered chainsaw that also uses the handguard
as a brake, we don't need that here since an electric chainsaw is never at idle. Now right up
front here is the scabbard. It just slides right off. Make sure you keep this because you're going
to always want to put it back on when you're not cutting. That way you keep the chain sharp for as
long as possible. Now let's take a look here and we will see that exposed we have a full 12 inches
of cutting. So that's interesting. Sometimes the bar is measured from way back here where it
actually makes contact with the mechanisms that hold it in place. But in this case, we actually
have a full 12 inches of cutting width which is pretty great. All right, there's a very big
sprocket cover here. And the thing that I'm most excited about with this unit is the bar adjust
locking knob and the chain tensioning knob right here. So with most chainsaws that I have used,
there is a one or two lock nuts right here that you have to use a separate tool to unlock.
And then you have to put a screwdriver in this way or back here to loosen or tension the chain.
It's pretty tedious, especially if you're just wanting to make a slight adjustment. Whereas here
you just simply back off the lock and then you can rotate this tensioning knob one way or the other
to dial in literally the best tension for your chain and then you lock it right back into place.
That is really cool. So this is the front handle right here and it has a slight angle to it to make
it a little bit more comfortable when you're reaching over for cuts. Back here we have the
rear handle and it's got a very slight kind of rubbery feel to it which is unlike my Husqvarna.
That one's just straight plastic. The RIDGID comes with the same sort of rubbery feel to it
which I like. Now up top here is the oil reservoir. It's just simply got a cap right here that you
take off. Unlike some units this one does not have a priming one. According to the manual the
20 volt unit has a priming little bulb up on top. The Ryobi also has that priming bulb. This one
does not. What's really cool about this one is inside of the reservoir for the bar chain oil
there is this filter and it fits right in there. It's a little screen mesh and so when you pour
your bar chain oil in here it will pre-filter it so you're not getting any debris. When you're out
cutting firewood you're going to be covered in sawdust and if you're coming in here with your
gloves on and you're pouring oil it's very easy for debris to get in there. The fact that they
put that little device in there I just think is really ingenious.
This little window right here is the reservoir. I did a review on the Ryobi pole saw and remarked
at how pathetically small the oil reservoir was. I was constantly having to stop and fill that.
Now this one when I put my finger in here it goes down to about right there so almost at the bottom
of this little window but I measured it it actually extends like all the way to here so
what you don't get in depth in horizontally you're getting a lot more space so I'm going
to be interested to see how much goes in there and how long it lasts. All right let's flip the
unit around and to the angle off a little bit here. Now right here is where the battery goes
and the battery simply slides on just like this and locks into place pretty secure there.
On the battery itself you simply squeeze the little orange piece on the back and that releases
the battery and it slides right off. Let's talk about the battery for a bit. This is a of course
40 volt battery and what I like about the 40 volt as opposed to the Black & Decker 20 volt
is this actually has a battery life indicator and when you have three like you do now that's
fully charged so a hundred or seventy two percent to a hundred percent. Two bars is 45 to 72 and one
bar is 18 to 45 percent so when you start getting down the the bottom of the one the unit is no
longer going to run it just shuts off. The charger for the unit is very small with the Black & Deckers
it's not a whole big thing that you click the battery into place it's simply a little piece
that goes up top so that actually slides right on the same rails right into place like that.
Right here is the charge indicator so you have this one light that can blink green or red.
Anything in green means we are either in the process of charging which is the blinking light
or solid green means it's finished. If it's ever blinking red that's not a good thing. If it is
blinking very fast red that means that the battery is defective and if you're getting a pulse of a
long red then a short red long red short red blink that means the battery is either too hot or too
cold. The best thing I find is you need to cool off these batteries for like 30 minutes inside
the house and it's best to charge them at room temperature so whatever you're comfortable with
is what batteries are basically comfortable with in charging. I also store my batteries
inside so that they're never subject to big sweeping temperature changes. Alright let's
talk about bar chain oil. The unit I got did not come with any bar chain oil at all. Let us know
in the comments if you got a unit that wasn't refurbished if perhaps it does come with bar
chain oil but any bar chain oil will do. Let's talk about some of the ingredients though. I was
reading in the manual and it recommended that if you're trimming a living tree branch say you're
pruning a living tree they recommend that you purchase a vegetable oil based bar chain oil
because that way it won't injure the living tree. They say not to use a mineral oil based lubricant
for living trees it could damage that wound that you create when you prune the branch off so I
thought that was interesting wanted to share that. For any other purposes any bar chain oil will do.
I'll leave a link to a couple that I like. So to fill it up let's go ahead and remove the cap
and then I have just this little automotive funnel that I like to use to make sure I don't
make a mess. Let's watch the oil indicator here and as I pour just a little bit let's see how
quickly it seems to fill up. I don't see much yet. Now we're just starting to see the indication here so
that's good. Get just one more little gulp and that brings us right up to the top.
Now I'm just going to take that and pop it right into here it can drip the rest of the way right
back into the bar chain oil and we'll put our cap back on. All right next let's talk about
tensioning the chain. So the manual specifically says that the chain should snap back into place
when it's pulled down about an eighth of an inch and that is proper tensioning. They say not to
have any slack in it at all. Usually I like to have a little bit of slack in my chains especially
my gas chainsaws because there's so much heating and cooling going on that you get
you get quite a bit of change. I don't like to have it too tight in the beginning.
So this one if we pull down you can see we got I'm just gently pulling down there's a little bit
of slack there and when we let go it pops right back into place. Now that is a sign that this is
properly tensioned. Now when I read the manual it said this unit comes disassembled that the
chain and the bar are actually disassembled from the saw itself. As you saw when I pulled
this one out of the box it was completely assembled. Let us know in the comments if that's
the case for you when you buy a brand new one. If it's not and they are now coming fully assembled
you can skip past this part or just for future knowledge continue to watch but we're going to
take this whole assembly apart here and we're going to simulate that we're putting it together
for the first time and also simulate that we're changing the chain out if it got dull. So lefty
loosey righty tighty we just unscrew this lock here and you can see it's integral to the unit
it doesn't actually come apart. Right there is the threaded piece. Now we have the sprocket back here
and you can see that the bar comes back to this area here and then there's a little free area
here that goes up to the sprocket and right here is where it is tensioned. It's held in place and
then moved back and forth to tension. You can see if I pinch it like that it becomes loose
and that enables us to pull it off the sprocket and remove the whole unit. Now if you notice
on these bars even though the writing is the same on both sides if you look on most assemblies they
are exactly the same and can actually be put on either way and that helps with wear and tear on
the bar. This unit is not that way. If you see it's got this piece here that you would have to
go the extra step of undoing this and switching it around and I'm not sure if it would be worth
it for wear and tear on that and the manual didn't talk about that at all. So if you were
changing the chain out the one thing you want to know when you orient the chain is look for this
is the actual cutting blade right here you can see the arrows pointing towards the front because the
chain circles clockwise as you look at it. Another way to tell if you're putting the chain on the
right way is there's this ramp right here leading up to the blade so you want to make sure the ramp
is in front of the blade facing forward towards the front of the saw. All right now let's get all
that back into place we're going to bring it back here right back onto that sprocket there we go
slide the sprocket cover back into place and we start screwing that down look around and make sure
we're caught up on something here it should be going in more than that.
There we go it was a I was seeing it standing a little proud here and it wasn't making contact
here so I had to kind of fumble around with it and pull the the bar out a bit but finally I got it.
Now let's check that tension again when I pull down here seems tighter than it was before but
I am able to get easily an eighth of an inch if not more so I'm gonna
lock that right into place for good and we're ready. All right before we get ready to start
cutting what do you say we do a little noise check let's see how much sound this guy produces
you can hear it kind of did a slow ramp up until it got to full speed kind of a throaty sound
let's compare that to the ryobi 18 volt all right no slow ramp up it's strictly full speed
and a little higher pitch to my ears. All right we're ready to start cutting I've got
hearing protection in I've got eye protection I'm going to put some gloves on here
and we're getting ready to start now to hold this piece of African sumac that we're going to be
cutting stable I have a cinder block here and it's got like a little groove in the bottom of it
right here that a tree stump this size fits in really well and that's going to help hold it in
place elevate it off the ground allow me to comfortably rest my foot on it and start making
cuts now a couple principles I want to talk about first safety when you're making a cut with any
chainsaw it's best not to have anyone in front of the chainsaw because in the unlikely event that
the chain breaks that chain could fly forward you also want to try to keep your body on the left
side of the chainsaw so that if the same thing if the chain breaks and it whips around towards the
bottom that hopefully it won't hit you right in the leg now sometimes when you're cutting that's
just not practical but it is a goal a second principle when you're cutting you can rest the
spikes on a chainsaw on the wood and help make like a cut angling into the wood and then you
come back angle a little bit more so you're always cutting a smaller area inside than
the whole diameter of the log now this Black & Decker the spikes on it are actually
plastic pieces of the body not true metal spikes like the Husqvarna chainsaw I have but
let's see how it does well it's not liking this log at all that's twice that it's cut out on me
this is a freshly charged battery we've got a full thing of bar chain oil and a fresh chain on here
it's not liking cutting this guy at all I'm not even bearing down on it very much
I don't even know if we're going to make it through this log there we go all right now
let's get a little comparison and let's try this Ryobi 10 inch 18 volt chainsaw it too
has a fresh blade a fresh 3 amp hour battery and plenty of oil in it this is a 10 inch chainsaw
and we actually have about nine and a half inches of reveal to cut with and as you can see
here that's going to be more than enough for this eight and a half to nine inch log so let's give
it a try well there's our first cut out I also smell electrical pretty decent on here like the
battery's getting hot but it's not it's not the battery it must be the motor let me get my glove
back on and we'll see if this Ryobi can handle this African sumac got some smoke coming out of
the motor cavity here there we go all right there's quite a bit of smoke coming out right
here I'm not sure if you can see that smoke coming out here too now I wasn't bearing down on it I was
letting the weight of the saw do most of the work give this little guy a break all right after one
cut with the black and decker as I look here we are about two-thirds of the way down in oil
so that reservoir is not really deep enough to handle the amount of oil that the saw naturally
puts out during a cut let's see if we can make one more and then I'll have to fill it again
that did pretty good on that one the only time it cut out that time is when I was trying to use
these spikes to actually get some leverage down on it it's better if you just let the weight of the
saw take it down through the log all right let's check the chain tensioning and see how that's doing
that's about the same which is nice that means that the heat hasn't affected the
tightness of the chain in one way or the other after two cuts we're already down to only one bar
on the battery so I don't think I'm gonna reach my honeydew goal of getting all these logs cut
with these guys today and we're after two cuts we're completely out of bar chain oil so let me
go get another battery and more bar chain oil and we'll see just what we can do with two batteries
all right so both saws are kind of struggling with that african sumac but that's a really heavy
dense wood this is a tree that actually died on our property and it's pretty light I forget what
the name of this breed is but let's try cutting this guy and see how it does this is also a much
smaller diameter probably yeah like six inches so let's see if it can handle this a little better
that's a lot better oh good it's starting to wonder yeah it took care of that no problem at all
all right this saw is really redeeming itself I'm almost full on this wheelbarrow over here
I think it's going to be much more suited to six inch diameter and under logs this small branch is
about 10 or 12 feet long here let's see how many cuts we can get we're still on the original battery
and the the second fill of bar chain oil and we're just seeming to hit our stride here
let's let the ryobi do one a lot jumpier oh I couldn't even make this little one
oh all right like that's pretty impressive we're still on the first battery and this is something
I just realized check this out with the black and decker you can see what the reading is on the
battery with the ryobi the way it's made the the battery indicator is on the other side this you
can't tell from here so you would have to physically remove the battery to check how it's doing I like
this a lot better all right I think this could easily keep going but we're running out of daylight
I filled this entire wheelbarrow full of pieces from the first stuff we started with that was
what nine inches in diameter down to these little itty bitty branches here and it's handling them
all with the exception of the really big ones very very well I've gone through two
reserves of the bar chain oil this is the the third time I filled it and I made a few more
cuts here and we still have plenty this is the first battery that I put in and it's still got
one bar I think when I first showed you that it was already down it was because it was getting
really worn out by cutting these big nine inch diameter logs it's been handling everything else
no problem I'm interested to see how far it would go on this battery but I still want to take
advantage of a little bit of the daylight we have left to look at some other things
first of all I want to look right in here and see how filled up we are with gook I do see
quite a bit of sawdust in there and oil which is to be expected because that means the bar
oil is doing its job and lubricating and that all looks really good I can see obvious signs
of the bar chain oil all over the bar it is very very oily so that's something to consider
the next thing I want to do is set this saw overnight right next to the ryobi and let's do
a leak test all right we're just going to repurpose the box that the Black & Decker chainsaw
came in it's a nice dry box no blemishes whatsoever on the inside of that cardboard
so let's set both of these saws they still have quite a bit of bar chain oil in them which isn't
the best way to store them but for the purposes of this test let's see what happens when they sit
out overnight all right 24 hours later and we can see clearly here a bunch of the bar chain oil
off the bar itself has leaked onto the cardboard that could have been easily remedied by actually
wiping it up before we set it down let's check underneath nothing nothing that's good
all right now the ryobi looks like there's a little bit right here and that would have been
right in the opening area where the debris is supposed to come out I think that also could
have been remedied by wiping the tool down prior to storing it so I would say they both did a pretty
good job all right this video is already over 30 minutes so let's wrap it up with the pros and cons
and who I think this chainsaw is for but first if you found this video helpful will you please give
it a thumbs up it really helps the youtube algorithm to suggest it to more people also please
consider subscribing I work really hard to put out good quality content and there's more videos to
come the pros the battery life turned out to be excellent as you saw I filled an entire wheel
barrel with just one battery the chainsaw was well balanced front to back and side to side
the cuts were very steady unlike the ryobi that was constantly bouncing the chain stayed properly
tensioned throughout the day and never had to be adjusted and I was very happy with the leak test
although I'd still be very careful to put something underneath it in storage now the cons once again
I'm very disappointed with the small oil reservoir it was way better than the ryobi pole saw that I
previously reviewed but still required four fills per battery which is just ridiculous
I used to regularly cut firewood up at our cabin in Utah with my gas powered chainsaw and I love
that the gas and bar chain oil lasted the same amount of time next I feel the chainsaw is
underpowered for a 12 inch bar I would love to hear in the comments if you've cut any softwoods
over 10 inches with it so who's this chainsaw for I would recommend it for anyone needing to cut
softwoods like pine and aspen but not for hardwoods like oak or maple it absolutely
struggled with the nine inch african sumac there is no anti-kickback nose on the front so be very
careful not to use the tip when cutting which could cause the saw to lurch up and cause injury
however the lack of that nose combined with its light weight makes it potentially useful for
ice and log sculptors speaking of the light weight I was hoping I could recommend it to
the log home builders out there years ago I built a log home with the help of my neighbor and we had
a small 110 volt chainsaw on hand because it didn't need to warm up for several minutes just
to make a quick cut and because it was much easier on the shoulders when cutting out the doors and
windows now while I think it could handle six and eight inch softwood cutoffs I don't think it would
efficiently cut out doors and windows the bar does have little attachment points at the front
which could be used to for attachments such as a log wizard style log peeler which are great for
shaving spots flat spots on the log for outlets and light switches we did that throughout our
log home and I thought it was a great design element I'll leave links below for all of the
items I've discussed now full disclosure these are affiliate links so if you click on them and
end up making a purchase it won't cost you a thing but I do get a small reward at the end of the
month it helps to justify the time and the money it takes to make these videos until next time
thank you for watching