In this video I show you how to diagnose the fuel & Ignition systems, determine the problem, fix it, and get your Polaris RZR 170 running again. The RZR 170 is the child size UTV with the 169cc four stroke engine. **NOTE: The starter must be cranking for this video to be helpful. If it is not, please check the battery, starter solenoid, and starter.
Welcome to my Waffle Square, where I obsess about things and you get to benefit from it.
So if you clicked on this video, I imagine you're like me and you're trying to figure out why your
son or daughter's RZR 170 won't start. Well, there's three main components or factors to
an engine running, right? We have fuel, we have compression, and if you're not running a diesel,
you have ignition. So in this video, I want to go step-by-step diagnosing the fuel system
and the ignition system. And a little hint, this guy's got problems with both of those.
So let's roll it in the garage and get started.
So the spark plug is where the fuel system and the ignition system meet. So the first thing we
want to do to assess both issues is take a look at that spark plug. And to do that,
we have to remove it. So right behind the passenger seat, right in between the fender
here and this tire, we head back to the crankcase and you can see right there in the center of the
screen, that is the spark plug wire. Just pull that out of the way and that is our tip of our
spark plug. It takes a five-eighths inch deep socket wrench to remove that guy. So let's do
that next. All right, coming in between the back tire and the shock is the angle that I found that
is best. There we go. I like these spark plug sockets because they'll hold the spark plug from
falling to the ground. Let's take a look at it. So I took the spark plug out because it's supposed
to be the window to a vehicle's soul. And look at all that black sooty carbon all over it. That's
a new spark plug too. So I googled the causes. A black feathery carbon deposit on your spark plugs
can be an indication of a weak spark or an overly rich fuel mixture. Causes may include a stuck
choke, misadjusted or heavy carburetor float, a leaky injector or carburetor needle valve,
low oil, excuse me, low coil output, or high resistance in your spark plug wires. The first
thing I want to do is rule out that it's a problem with the spark. So let's clean this guy off
and then check it for spark. So we have the spark plug wire here. I cleaned off the spark plug and
I've got it set against the crank case and I checked and made sure that the engine is properly
grounded to the battery by putting the red lead of a volt meter on the battery and the black lead
over here to ensure that I got 12 or 13 volts, which I did. I've got this guy pressed against
the metal, so that should give us a spark right here. I've got Aspen, my little helper, so I can
actually see along with you. Aspen, give it a crank a few times. Once more. I don't see any spark.
Let me get something plastic to push against there. Let me make sure that we've got metal
on metal contact with this little plastic piece. Go ahead, baby. Once more. Nope, I don't see a spark.
Well, there we go. So did you have a spark? Well, if so, just keep watching. We're going to roll right into
fuel system delivery. No spark? You might want to skip to this spot right here where we start
diagnosing the ignition system. So coming in from the passenger side, let's go over a few key
components. First of all, this guy right here is the choke. On really cold starts, you need to pull
that choke all the way out. Once it's to idle, it should be all the way in or close to that. And
that's where you generally want to run it. And it should run its best warm with no choke at all.
If you don't already know, you have to push the brake down while you try to start the engine.
And now let's head out. And right by the passenger seat here, this is your gas tank right there.
Straight down from that, this is the fuel selector. There's a little arrow right here,
and there's an on and an off written right on the fuel selector. So the on should be pointing
towards the arrow. If you look at yours and it's turned up like that, your gas is turned off. And
that could be an easy fix. Now directly back from that, behind the rear passenger tire,
is this. This is the fuel pump. There's a line coming in from the gas tank. Then behind this one,
right back in here, there is a line that is heading to the fuel filter and the carburetor.
And this one right here heads right over here to the crankcase. And that is supplying the suction
to draw the fuel up in through this fuel pump and over towards the filter and the carburetor,
basically. Quick word about fuel. So the shelf life of regular gasoline is three to six months.
Therefore, if your Razor's been sitting around for that time or longer without running,
the gasoline inside could be stale and that's very bad on the engine, or at least it won't
run very well. So if there is a lot of gasoline in here that's very old, you may want to consider
removing it. I got underneath this guy and I couldn't find an actual drain plug. Let me know
in the comments if you know where it is. But I do have this guy right here that is for removing
brake fluid from the master cylinder when you flush the whole system out. I recently did that
with all of our vehicles. So you could do that. And if there's only a small amount of gasoline in
there, then like a professor taught me in college, dilution is the solution to pollution. So in other
words, dilute that bad gas with a bunch of fresh gas. And in this case, that's what I did. So I'm
not going to be draining anything. Let's go back and test the fuel pump. If you were just looking
at the pump or wanting to work on the pump, you could probably get to it from behind the
the fender in there. But I'm going to take the seats out and take this panel off. It's actually
pretty easy and it's going to give us a whole lot more space and also much better camera angles. So
the front seat, the driver's seat, excuse me, there's a little lever that you push and slide
it forward just like on any other car. So you slide that forward and it just comes right off.
If you weren't already aware, that's where the battery is located. Passenger seat has two 12
millimeter bolts under here that get removed and that frees the seat to be removed straight out.
This panel is a combination of 10 millimeter bolts as well as the little push pin remover
for plastic panels in a car. After removing all of those, you can just slide this panel right out
and set it aside. All right, let's get our bearings. So these two points here are where
the passenger seat connects into. So be right behind where the passenger seat would be is what
we're looking at. Down here is the actual fuel pump. The line coming up from the fuel pump
to the filter is right here. Here is the fuel filter. This is not the original. I have changed
this one out. This one actually came with the carburetor and I'll show you that a little bit
later. But over from the filter right here behind this stuff is the actual carburetor itself. More
on that a little later. And by the way, this is the starter. Now I've recently replaced the starter
because the kids burned it out and so did I trying to assess what was wrong with everything.
If you have any interest in seeing how I replace that starter, let me know in the comments. There
are other videos out there that you could find but I'd be happy to do that for you. So let's
start by testing just the fuel pump, not the fuel going through the filter in case the filter is
clogged. And to do that we want to take off this little pin right here. You just squeeze it and
you can move it back along the hose or in this case it actually just comes off this way. I'm
going to get this little cup right here to try to catch any gas coming out of that filter so we're
not making a mess. There we go. All right, one hand on the brake, the other one engages the starter
and let's see if we can get some fuel to come out. So there is fuel coming out of there but that
looks like it's pretty low production. So I think it would be interesting to switch out that fuel
pump for another one. All right, looking in from the back wheel, here is our pump. There are the
hoses that need to be removed and then two 10 millimeter bolts. So let's get the hoses first.
Once again you're simply pinching them. I have a little pan down underneath to catch any gasoline
that comes out. Okay, there's that one. This is the breather tube or vacuum tube and now the one going
from the gas tank. Let's turn off the fuel. There we go. All right, two 10 millimeter bolts. Well here's
the original and here's the new one by Most Plus. I'll leave a link for it in the description. You
can see they're almost exactly the same so that's pretty cool. All right, let's bolt it in and then
hook up all the lines. Next we'll put in the fuel line since it's a little further back than the
vacuum line. I'm gonna reach in there put the clamp on just like that and then our vacuum line
goes right here. Clamp that down. Now the manual says to make sure none of the lines are kinked.
So then you trace them with your eyes and with your fingers. Make sure there's no crisscross
cranks in there anywhere. All right, now let's test and see if we get more fuel production.
Oh, we got to turn the gas on. Here we go. Oh yeah, that's a lot more coming out. All right,
the next step would be to disconnect this hose on the outflow side of the fuel filter
from the carburetor and do the same flow test to make sure that it's not clogged. In our case,
I've already replaced this one. It's fresh and clean so I know it produces well. Now if this
solves your problem and it fires right up, will you please give this video a like and that would
be really helpful. I'll leave a link to the fuel pump down below. It's only a $13.50 item. Now in
our case, we're not going to stop there. For the purpose of this video, I also elected to move on
to the next step which is to replace the carburetor and that is a $28 item. There is no rebuild kit for
the carburetor sadly so it's it's just part swapping and we're going to do that next.
After a few days, the new carburetor I ordered came in. Let's take a look at it.
First, it comes with its own fuel filter which is fantastic. Now I'm really not happy with the
packaging because look at this. It completely crimped one of the hoses. Luckily that's just
the one that drains it and there's not much room for it anyway. But everything else seems to be
functional and intact. Let's switch it out. Since the carburetor is right back there, I'm going to
take this panel off right here. We might end up taking this big one off if we need to get down
to it but I think I can reach through. So just like the panel behind the seats, we have 10 millimeter
bolts. There's actually six of those and a couple little pop outs, one on each side. Looks like
there's a phillips screw right here that's holding this guy in place. I got it. Looking in from the
back wheels, we can see the carburetor right here. There's a little breather tube kind of in the way
but we'll be able to get to it no problem. Now this aluminum pipe you see here is an aftermarket K&N
air inlet with an exposed filter up top and that's held on just by this little clamp right here
and then we have a little quarter inch hose clamp right here that is heading into the engine
crankcase. So let's take those two off and then right up here we'll also untwist this little guy
which has the throttle cable going into it. That came off super easy. Let's unhook the throttle
cable, the gas inlet, and the choke. Right there is the choke cable. Let's loosen this guy up that's
actually holding the outer shell of the cable. Got a little little jar again for the fuel line.
Let's pull that guy off. Okay then we can get in here and let's undo the throttle cable.
Now let me get in here this other direction so you might be able to see there. Okay there's a spring
and then this piece here. I'm going to pull all that out. I don't see any reason why we can't reuse that
if it's in good shape. Now the only thing left holding it on is right here and I've loosened
that plenty. You can see it just spinning freely so let's see if we got better leverage over here
to pull that off and if not there's a couple nuts here that we can take off.
Yeah that really doesn't want to come off so maybe we'll just take these two off.
I bet you they're 10 millimeter. Yep 10 millimeter. All right so here's the two
carburetors side by side. We just have to take off this little piece and transfer it over here
and you can see with the exception of the dirt these things are practically identical. All right
this is the air inlet. Looks like when they did the K&N conversion they just cut off the original
and just left enough for it to clamp on to so we're going to need that part.
Finally. All right let's get this guy popped on here.
All right that is plenty tight. This whole assembly here is doing great for the choke.
I think I'm just gonna loosen this one though so we can get that choke cable in there
pretty easy. There we go and might as well pull that guy off. I'm not too worried about dirt
getting in there at this point. There's a little O-ring here. I'm going to lubricate that with
just a little drop of oil just so it gets a good seal since that's heading into the
crank case and that is creating suction to draw the gasoline vapors into the engine. We want to
make sure that's a good seal. All right we're ready to put it back. One more thing. This whole
assembly here I checked the other one and it's all in good shape. There's no wear on this little
needle or anything like that so I'm just going to use the existing one since the throttle cable is
already into this little linkage down there. I checked and this gasket is still up on the
original one and it looks fine. So let's leave all that out of the way and now we're ready.
All right let's see if we can go through this a little quicker now since you already watched me
take it off. First thing I want to do is get it right back onto those two bolts just like that.
Let's hand tighten those 10 millimeter nuts. Good. Now let's put the throttle cable in.
This little guy here has to twist in a specific way for it to go all the way down just like that.
There we go. Let's test that with the gas pedal. I can hear it in there so that sounds good.
All right let's do the choke cable next. Now we got to get this guy into that little hole.
So if we turn it up, pivot this on the wire, slip it in like that. Boom. Okay next step is to get
the end of that cable into that spot where we can clamp it down with the
phillips head screw. Now let's test that by pulling the choke out. Yeah good. All right
see this rubber piece for the intake, the air intake? Make sure that's not rubbing against
this part of the choke or it'll make it stick. That's working good though. Okay next let's do
that real easy breather tube. One's right here. All right let's weave the gas line in there.
Boom. Now we got to get that little clip. Okay that's just about everything on this side.
So now we had loosened this little clamp. See how loose that is? It's just kind of wobbling
around. Let's tighten that one with our quarter inch. Plenty tight. And lastly let's get this
air inlet into place.
One last check of that choke. Make sure that's not interfering anymore.
Nope. Still good. All right. So that solve your problem? If so, could you please give this video
a thumbs up? I'd really appreciate it. If not and you have adequate spark, then maybe you've got
some sort of compression issue going on. Well now we're at the point in the video where we're going
to start diagnosing the ignition system. First step in diagnosing the electrical system is to
start right here with the spark plug. It's all cleaned up and we need to test the resistance
between the stud and the electrode. So I've got this awesome little Kyweets multimeter. It actually
has an automatic function. It can just sense what you're wanting to do. So if you put it on
the terminals of a battery it'll sense DC. If you put it in a wall it'll sense the AC.
In this case it's going to sense that we're wanting to check ohms of resistance. We should
get that same green light and tone when we touch one end to the stud and the other end to the
electrode. Get it down there. There we go. So we know all the way down the spark plug is good
and obviously this whole area here is basically one piece so it's good too. Give me a tone okay.
There we go. All right spark plug's good. To diagnose the electrical system we're going to
need to remove this seat so we can get to the battery. That seat so we can get to this panel
and remove that panel so we can get to all the ignition system that's running right behind these
two seats. It's really not as hard as it sounds. This driver's seat there's just a lever right
down here just like any normal car. You pull that up slide it forward. We need some oil.
There's our battery. Right underneath the passenger seat at two spots there's 12 millimeter bolts.
Seat belt's out of the way. This guy just slides.
This back panel runs from one side all the way to the other and about three quarters of the way up
down to here and it's held on with a combination of 10 millimeter bolts and the little pop out
little plastic retainers that are used for car door panels. So let's start removing all those.
These little retainer clips if you ours if you just start popping them out a little ways
from the middle I can then get in there with a
remover tool a little fork we'll pop it out the rest of the way just like that.
We just slide this guy right out. All right let's take a look at the battery next. All right let's
get our bearings. This is where the driver's seat was. When we slid that off it exposes the battery.
We want to test the voltage of the battery to make sure that it is sufficient to operate the
ignition system. 12.87 volts that's great. Now we want to test that the engine is properly
grounded because the spark plug gets screwed into basically into the engine. So let's test that
and once again yep 12.86 volts 87 so we're doing great there. All right moving on to the process
the next thing we want to do is test this guy. This is our ignition coil so let's reposition
the camera and get to that. Okay right behind the passenger seat is this ignition coil right here
and there are two wires coming into it. One is yellow and black the other one is green and then
heading out the other direction leads all the way down to the spark plug wire here that the spark
plug head goes into. So first thing we want to do is draw back this little rubber boot
and it exposes those two wires and look at this black and green and then right here black and
green so you can't screw these up when you're connecting them back. That's pretty cool. Let's
disconnect those. All right first thing we want to do is test resistance from either one of these
terminals to the spark plug wire here and according to the manual which I'll leave a link
to that should be a reading of 8k ohms of resistance plus or minus 20 percent. So we've got
our little terminals here or our little needles here that we want to probe and check with and
let's first check if there's any built-in resistance in the line. We're showing like
just a tiny bit right. All right so let's put one of these cool little attachments on here look at
this little alligator clip pushes right on here like that. I got that off of Amazon it makes it
really easy when you're doing this by yourself. So we'll set that right on there and then the
other end is going to go right into where the spark plug connects and let's check yep 7.71 so
I think that's well within 20 percent of 8k. Very good. Now when it comes time to test the primary
which is the resistance between these two terminals the manual says it's supposed to be
0.2 ohms but this little guy here doesn't seem to read down to that level in fact I check the
manual it only reads down to 50 ohms. So we're gonna have to switch over unfortunately.
Let's get this guy out of the way and we'll use this one. Now this guy unlike the little
Kiwi Twin this guy when you check it has uh look at that like quite a bit of built-in resistance.
Remember the other one was like 0.0001 this one's 0.2 on its own so if we were to take this reading
without checking that first it would be off so 0.2 0.3 so we're looking for
what 0.4 0.5 when we test across here and let's see what we get yeah 0.5 0.6 so probably within
that 20 percent realm so yeah 0.5 0.4 0.5 there we go so that tells us that this ignition coil
is fine. Well what if it wasn't? What if that was your problem? Well you could go on Amazon
and you can buy this perfect replacement right here for ten dollars and all you have to do
is take an eight millimeter ratchet to this one bolt right here holding this in place
and clip one zip tie that's holding this wire down by where it goes into the crankcase and you
could replace that whole unit just by backing out this one bolt but since this isn't our issue
the manual says we want to move on and test the CDI box so let's set up for that next.
All right as we zoom in the driver's side back wheel right in between the shock and
this crankcase breather tube and above this aluminum guy with the heat dissipation
right here we see the two plugs to the CDI box so this is a very expensive unit it's 226 dollars
and this is what it looks like so we've got two plugs and the next couple tests involve those
plugs so the first one we want to disconnect this one over here that is the two wire plug
and see this brown wire right here we need to turn on the ignition
and check for voltage between that brown wire and the engine so we're going to set our
voltmeter to DC we're going to test positive here and then the negative is going to be on the
engine and let's see if we get voltage. All right the CDI box is up here on a little metal flange
and it's surrounded with this rubber boot and it'll actually slide off of that see that little
guy that's holding it in place and that makes it a little easier for us to get access to these two
plugs so I'm going to disconnect this little guy and set up the voltmeter and we'll come back and
do the test. To get this plug off we need to bend back this little tab that releases a catch and
then pull this plug out. All right I have the red probe into that brown wire connector I have the
black probe on the engine block itself we're set to DC volts so let's turn the ignition key on and
see if we get voltage. Yep so that wire is not the problem the next thing we need to do is take
off this four plug and we need to check continuity from this black wire to the engine ground. All
right we've got the black probe into the black wire connector we're set to continuity test now
I'm going to take the red probe and just touch the engine yep we passed that test. So while we're
here with the four wire plug out of the CDI box we can test the pulsar coil resistance
which is found in the manual and that should come out to 151 ohms plus or minus 20 percent
and to do that we go blue yellow lead and black lead and test their resistance
143 so that passes. Well going down the flow chart in the manual the next step is to go
back to the ignition coil and check for continuity between the green wire so disconnect it and check
for continuity between the green wire and the wire underneath the key ignition when you turn it
to the on position it doesn't specify which wire I tried the green one and that one's always grounded
there's a black one right next to it and if we get our probe in it when we turn the ignition on
we get the continuity so we pass that test. So the stator as pictured here looks like this snowflake
of little coils and it's inside the crank case and as the crank case spins all those little
transformers create electricity just like lawnmowers and everything else that spin like
that to produce their own electricity well the cable that comes out of that is right here
and it comes right to this connector and there's some tests we can do to see if the resistance is
within the right parameters in there it would be quite a job to take that crank case apart and
replace that so let's test some resistance first but look at this fitting and all this oil around
here that has built up it's really dirty now I read in one of the forums that a lot of the times
these issues can be a bad connection and the manual states you know check all your connections
as you go along through these tests as well so what do you say we clean this up a little bit
I'm gonna put a rag down here and spray some cleaner on it and let's let's see if we can't
clean that up a bit it can't hurt it's really nasty
yeah it's already looking better let me get a rag in here wipe all this off you can at least
see the wires and the connector there we go what do you know there's actually wire colors
that we can see now and test so let's do that to separate this connector you lift up on the
little plastic tab over here and pull it apart and that gives us this one that's heading down
to the stator and we have a blue wire a black wire a yellow wire and a red wire and we're going to be
testing three of those so the first one we want to test is black to ground so I've got
one probe on the engine ground the other one going into this black wire and we went from
0.3 0.4 to 0.4 0.5 or so so we are getting a little bit in there so that seems all right
next one is black to yellow and that should be 0.9 and we're right there and then the last one
is black to red and that should be 1.1 and we're right there well that's a good thing
all right the next test of the stator is to switch your multimeter to AC
and get in output readings from the stator on the yellow and the red
wires so I've got the probe into the yellow and the red probe onto the engine ground
and we should get eight volts AC here we're getting about six and then red to ground
we should get five and we're getting like 10 but at least it's working all right after cleaning up
all those connections pulling everything out testing putting all the connections back
just for the heck of it I had to try sticking the spark plug in there and doing another spark test
and watch this I'm going to turn off the light you see that we're getting spark all right maybe
it was just a bad connection all along all right got everything buttoned back up let's see if it'll
start hey hey a little something all right what can we do obviously need to adjust the idle
obviously need some idle adjustment but mommy's gonna run it out
music to my ears well obviously the carburetor needs to be adjusted but this video is going over
40 minutes already and there's a lot of things that can be adjusted the air fuel mixture which
is the pilot air screw then the idle speed there's also the throttle needle as I start researching
that has little tick marks in it that you can adjust so we definitely need to break that out
into another video now there were two other tests in the ignition diagnostics that could
have been performed one on the cdi box and the other one on the pulsar coil and both of those
required this which the manual called a peak reading adapter but in reality it's a dva or
direct voltage adapter you won't find it under the term they use in the manual but basically
it plugs into your multimeter into the positive and negative and you use this to get peak readings
that it can keep track of and give you the outcome for those tests as you saw we ended up fixing the
problem prior to getting to those tests so this was still coming in the mail and this video is
so long that I'm gonna forego those tests but if you've watched this you know where everything's
located you know how to remove those plugs and I think you'll be able to read the manual and
just get those last couple of tests done yourself if they're required now normally when I obsess
about something I get focused in and I can't get out of what brooke laughingly calls a waffle square
until I solve a problem and I have to admit that this one I went into reluctantly I was not excited
about deep diving into this I was actually hoping the kids had outgrown it maybe we could sell it
but the 12 year old sees her 16 year old sister driving now and is wanting to be a big girl so
she's taking over this guy putting stickers and things on it so I did have to figure it out and
I'll have to tell you this was a really difficult fix for me because the manual assumes you know
where all of these parts are it gives you a very close-up little thing of them it doesn't really
show you what they look like or where they're positioned on the vehicle I was crawling all
over this thing having no luck I actually had to google the parts to find out what the replacement
parts looked like so then I could then crawl around and find where each of those things were
to test them so my hope is with this video that it cuts about a week's worth of that kind of headache
out of your life and if you find it helpful will you please give it a thumbs up and then drop a
comment for me let me know that would be great it would mean a lot that all the work I put into is
is helping others I'm not on Facebook but if you are maybe you could post it and share it somewhere
for in a forum or a group or something where people might benefit from it that would be awesome
and if you're in any kind of UTV forums maybe post a link for it there as well I would really
appreciate that I'm going to leave a link to all the items that we talked about the replacement
parts and the tools I used in the comments below full disclosure those are Amazon affiliate links
so if you click on them and end up making a purchase it won't cost you a thing but I do get
a small reward at the end of the month and that helps to justify also the time that it took to
make this video our next video is going to be me trying to adjust this carburetor it's backfiring
and there's a lot going on so maybe hold off on buying a new carburetor it might be easier after
you watch that next video to just clean up the existing one you have maybe take it off clean it
up take out all the needles and those sorts of jets and things and and put it back together and
do it that way but we'll find out on the next video until then thank you for watching