Segway {Sur-Ron} X160 Complete Teardown - Ep.2

Waffle Square
9 followers
In episode 2, I completely disassemble the Segway X160 Electric Dirt Bike.
https://www.segway.com/dirt-ebike/
Amazon Affiliate Link:
VIVOHOME Hydraulic Motorcycle Scissor Lift Stand: https://amzn.to/3SeOmTI
Camera Gear Used:
Canon EOS R6: https://amzn.to/3NfUvwk
Canon RF 15-35 2.8 L: https://amzn.to/3RWE5rI
Rode Wireless Go Lavaliere Microphone: https://amzn.to/2GHU237
Canon M6MKII (B Cam): https://amzn.to/49avSto
DJI RS 3 Mini Gimbal: https://amzn.to/3QeACpt
Video Chapters:
0:00 - Intro
1:00 - Teardown
17:06 - Conclusion
Views and recommendations expressed are my opinion based on hands on testing, experience, and results.
Email: [email protected]
#segway #ebike #surron
Welcome to episode two of our series where we are going to completely refurbish this Segway
X160 all-electric motorcycle. Now in episode one, I told you all of the issues that were wrong with
this bike, where I got it from, and what the plan is for it. So if you haven't watched that video,
I highly recommend you go back and watch that one first.
Brought to you by Waffle Square.
Thank you for tuning in. My name is Mike, and this is my Waffle Square,
where I obsess about things and you get to benefit from it. So in this episode,
let's get started completely breaking down this motorcycle. Safety first. Let's go ahead and lift
up our broken battery cover. I want to remove this battery and also turn off the breaker,
and then we'll start the whole teardown. So let's reposition the camera and get started.
Take this broken battery cover off. On either side, there are these little metal pegs coming
through like hinges, and there's a little catch ring or snap ring right there. And I tried just
pulling it off with pliers. That didn't work so well, but what does is getting under there with
like a little pick right at the top, bending it off just like that. Then we can ease that little
peg out, that hinge pin, and this whole broken cover is finally done. Buried under this nylon
patch and this nasty glue is supposed to be this ignition and USB port bracket. So let's take this
out. This is a number four Allen. This speedometer screen is a little jacked up over here, but it
works. So I have a bracket that it's going to sit in. Let's disconnect that and set it aside. So
right in the same area is this plug, and it looks like it's the one that's yellow, green, black.
There we go. Now deeper down in this front area by the gooseneck are the two plugs for
the front and rear brake sensor. Let's disconnect those. There we go. And up here we have the sport
mode, eco mode, and horn switch that we are going to be changing out. So let's disconnect that.
That's on this one here that is black, green, and white and green striped. Now the throttle wire
goes all the way down to the bottom of the controller motor area, so we'll have to pull
that off and just let it hang. But let's get the brakes and this selector all off. They're the same
Allen wrench and number four, and this is all garbage. We're replacing these. Check out this
nasty old torn up grip. This battery pan is held in place with five number three
Allen screws. So I got these five screws and then two bigger screws up on this piece of the plate,
but it seems to be maybe clipped into something down at the bottom because it ain't coming out.
Somebody's laughing at me in the comments right now.
Let's get this front wheel off. Look at how loose and janky this is. It wasn't even tight.
So instead of all these washers, there's supposed to be two spacers as you can see here,
and I have those on order. So I'm hoping all these washers haven't damaged it to the point
where we can't put the proper stuff on. So what do you say we kick out this bolt,
get all these washers off, and let's try the axle that I've already ordered and see if
it's going to fit tightly. Otherwise, we may have damaged these forks beyond repair.
There we go.
This is what the axle is supposed to look like,
and this one does not fit in these forks. I wonder if there's a bushing or something in there.
It doesn't feel like it. Let's see about the tire that came with it though.
It doesn't really fit in there either, so that's good news. Maybe I'll be able to...
No, it does. So this axle's pretty much correct for this wheel,
but not for these forks. We're going to have to work on that more and get those parts ordered,
or we won't have a way to attach this wheel. Well, taking off the front tire has got this
whole bike up like that, so let's even out the weight and take off the rear tire.
First thing we need to do is remove the brake caliper, and that is a number five Allen.
Then we got a 17 millimeter nut on this side and a number six hex on the other,
and I believe these are supposed to be opposite threads. Yeah, there we go.
I'm just pulling out that axle, see if we can push it up enough to get the chain off.
All right, let's take these mystery forks off. We've got this cross brace here that has two
number fives, and then back behind there is another number five Allen screw. There's that.
Gently get it out of here. Oh, there. Let's take the seat off. I think the screw we need is under
here. Instead of an actual tail light, it looks like we have like a headlamp that you wear when
you jog around. That's what that looks like, so let's go ahead and take that off. We can do better.
Yeah. So here's our reflector. There's a couple of Phillips screws. All right, let's take off
these two 10 millimeter bolts and then attempt to get the seat off. All right, I took these two
bolts out front so the seat can pivot up enough that I can show you. See these little black pins
that go all the way across? Those need to be popped out so we can get this cover plate off
and finish taking off the seat. Now, I have these panel clip pliers. I've used these a lot.
These are so small, I'm not sure it's going to work in this case, though. See that?
Can't really get purchased, so let's try a flathead screwdriver. If not, we're just going
to have to get like a pocket knife. That's not working either. Let's try this. This is almost
like a dental tool, and it's actually made for pottery. There. Wow, that is an incredible pain.
Well, that was way harder than it should have been. These little plastic panel clips, I've never
struggled so much with them and broke so many, so I'll be researching how to get new ones.
There's still something holding it on up here somewhere I can't find. Oh, it's more of them.
Oh, goodness. Oh, we have a tip sensor or a seat sensor on here. Cool. There we go.
All right, now let's take off the seat bracket here. There's what probably used to be a 10
millimeter bolt right there that's been broken off, but we have this one here. Let's see if we
can get it. Yeah, and then these and the two on the other side are number five Allen heads.
All right, getting there. Let's start working on this lower assembly here. I want to
release the shock absorber from it first, so that's the number five Allen here and a 13 millimeter
nut on the other side. Easy. Go. That's all nice and glued in. That's my favorite right there.
Keep all these bushings together for now like that. All right, cool.
Do you plan on stripping and painting this? Yeah. Yeah. Yeah, because all this speckle all over it.
It's awful. I just wanted to know if you were going to do a half-assed job.
No, I'm going to do the full job. There it goes. Thank you. What tool is that called?
These needle nose pliers. Oh, they're just bent? They're just, yeah, they're rounded so you can
get into a little tight spot. Nice. There's got to be some bushings in there because that's not
just coming right out. Nice. We'll get our spindle out of here with this gear on it.
It looks okay. This is a little bit dinged up. See that right there?
That's probably what's causing the side wear on the belt. Hmm. Let's see if we can pound that out
or source a new one. Let's take the controller off. It looks like all the hex nuts here holding
it on are all number four. We got lots of wiring going on in here. Got this guy, big one here.
Let's see if we can clear out this wire by removing this assembly here for the breaker switch.
So this is like the main plug cable leading up into here from the controller. So let's
take off the horn bracket and see if we can get our hands in there to disconnect this cable and
get one step closer to getting the controller off of here. Two plugs here for the horn.
I don't see any color distinction.
There. And there is the plug for the controller. Maybe we can pull it out this way. Yeah, I can get
it. Get to it here. Let go. All right. So there are two more plugs buried in there. There. And
I see some big cable connections down here. Those must be going to the motor. And so we'll
probably need to take this skid plate off to get to those. All right. That's a better angle. Let's
get the yellow, green, blue cables that go to the motor disconnected, as well as the black and red
that are heading up here to the breaker. And that will allow us to take the controller
off and away. Those are on there good. And there we go. I've just got to get this pink off, but
otherwise it looks fine. This is the throttle. So for future reference, when we put the wiring harness
on, the wire that's coming right off of the big rubber insulated boot is for the throttle.
Okay. We need to get this skid plate off so we can get at the rest of these. And finally,
the motor. These are number five as well. Hi. Yeah, you're on camera. Say hi to YouTube.
You don't have intramurals today? No. That's nice. Well, I mean, I almost fifted on the
pickleball court last night. All right. Here comes the motor. Yeah, that guy's hefty.
Somehow we still have one plug. Yeah. Nice. And with the motor out,
let's get this one more little retaining clip right here. And with that, this entire wiring
harness comes out. Last thing is to remove these foot peg brackets. Oh, that one's a beast.
You want to be that way? We'll introduce you to Mr. Breaker Bar. There it goes. There we go,
right? Other than this little plate. Let me take that off. And that ought to do it. Completely
stripped down to the frame. So if you enjoyed this episode, will you please give it a thumbs
up? It really helps the YouTube algorithms to start suggesting it to more viewers like you.
Also, please consider subscribing. Go back and watch the first episode.
And then there's plenty more to come as we next strip and repaint the frame and the other
brackets that go along with it, plus anything else that has this flicker overspray. And after that,
we're going to service the forks and then finally start putting everything back together. So until
the next episode, thank you for watching. That was kind of you. Not a bad gig, Eddie.
She's more hospitable than you. That's true. I've been here for three hours, sweating to death.
That's why it's called Waffle Square, because I'm just in it. Yeah, you are in it. I could
probably drop dead and you'd just step right over me, try to get that plastic piece out of there.
