Hi, I'm Mike. Welcome to my Waffle Square. I obsess about things and you get to benefit from it.
Well, in episode three of our ongoing series where we are updating my daughter's 2013 Ford
F-150 with the EcoBoost engine, we are going to be replacing this tiny inconsequential bump stop
on the rear axle with these awesome MaxxSpeedingRods rear suspension helpers.
But what are they? Obsession. Brought to you by Waffle Square. So these MaxxSpeedingRods
rear suspension helper springs are specifically designed for the 2004 to 2014 Ford F-150.
They are a leveler when you are under load or towing and they're a dampener when you're bombing
down rocky bumpy dirt roads like Aspen does. When we first bought this truck the rear shocks were
so bad it was unsafe to drive off-road. So in episode one we replaced the rear shocks and now
we're installing these awesome bumper springs. Now full disclosure, MaxxSpeedingRods did send
us this kit for free when they found out what happened to Aspen's LR3. They want me to stress
that these do not increase your load capacity which is about 1,200 to 1,600 pounds. So you
can't haul crazy loads like this. With that out of the way, let's get to the install.
So before we do any work, underneath the car I'm going to chock the tires.
I'm going to chock it there since garage slopes outwards and then anytime I have an opportunity
to work on any part of the car I always trickle charge the battery. All right, the instructions
say that the first step is to remove the existing bump stop with a 13 millimeter socket. Which on
the surface sounds really easy but you have this opening here going right down to here. You are not
going to be able to get an entire impact wrench in there to drive this out. Instead you need to
put a socket on an extension and then probably start with a breaker bar to get that loose enough
and then maybe I've got a battery powered ratchet that can get it down the rest of the way.
There we go. That wasn't easy but there is the original bump stop. You can see how much smaller
it is than the max speeding rods and I'm glad we're getting a new bolt to put in because that
one is nasty. So all this is going to do when you hit it is feel like you just went steel on steel
where this is just built to be like a big rubber spring that's going to have more give when you're
bottoming out. So it just won't feel like you're just smashing down on rocks. Now the next step
according to the instructions is to assemble your new spring and that consists of this bracket,
a spacer if you have room, the spring and a bolt going through. Now according to the instructions
you need to have a minimum of a half inch down here between the spring itself and the vehicle
so that it's not just like riding on here or it's too close and it's always hitting it. So as you
can see in this picture here we have more than enough room to a lot for this extension so I put
the extension in and that takes the longest screw in the package which is a 65 millimeter bolt. Then
the instructions say the next thing to do is install the new spring fully assembled onto the
frame of the vehicle. But take a look at this and see if that doesn't quite make sense to you.
Watch as I turn this and you can see that's where the bolt goes that goes into the frame of the
vehicle but there's this hole right here that perfectly aligns where you could get an extension
and run your impact wrench on there to mount this bracket first. So it seems strange to me they would
tell you to assemble it which negates that ability to use this hole and then you're just supposed to
get in here with the socket wrench and you're just going a small way back and forth whereas if
you use the extension you could drive it up there first and then simply run the bolt through this
guy to finally mount it. So I think I'm going to do that instead. Now before you go installing these
new brackets make sure you look right here it's an R for the right side and not here but up here
is an L for the left side. All right here goes our bracket.
Well it's going in here nice but to get a socket in here to tighten this up we're gonna have to
jack up the car on the frame to separate the axle from the bump stop.
Yeah that's what I'm talking about. Man look how pretty that looks and there's
just no arguing that that's gonna have way much more of a supportive impact
hitting here than having to be compressed all the way down to there. Just a huge difference.
And there we go. Way less technical than installing airbags with the compressor,
the tubing, and the wiring while still offering great performance under load.
So if you found this video helpful will you please give it a thumbs up. It's really helpful
to the channel. Also please consider subscribing. I work really hard to put out good quality
efficient automotive content and there's a lot more videos to come. Now I would like to thank
Mack's Speeding Ruts for sending us this kit for Aspen's truck. Fantastic. I'm going to leave a link
for this exact product in the description below. So click on the more and it comes down. You can
see the website for Mack's Speeding Ruts to find it. It'll also be in the YouTube tagged product
section of the video. And if you want to see a review video of these sweet work gloves check out
this video here. But as always thank you for watching. Did you notice this video was posted
midweek? That's because starting this Saturday we are going to be introducing
the new LR3 project. Oh yeah. Hung by the tongue now I have to get it done.