Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with another
cool arcade game repair video for you
this evening.
This time we have
Popeye
by Nintendo.
This is our buddy Trevor's machine. He
actually just picked this up yesterday.
I think he went to Virginia or somewhere
to get it.
I wasn't here when he dropped it off,
but I kind of already know what's wrong
with it. He told me he told me what was
wrong with it.
It's broke.
Now, before I even get started,
I kind of want to address a couple
things on my last video with the shadow
pinball machine.
The comments, a lot of the comments I
kind of want to address. You guys didn't
get the whole story. A lot of people are
like, "Well, you shouldn't have took the
job if you didn't want the job. He's
paying you money." No, no, no. He's too,
you know,
you didn't get the whole story.
Uh, but basically, the guy called me. He
wanted me to clean and shop that pinball
machine.
And uh I told him I didn't really do
that. We mainly do more repair work. We
were a repair shop, but he couldn't find
anybody else to work on it. And he said
it really needed shopped real bad. So,
you know, against my better judgment, I
went ahead and told him that I would do
that even though it was a DMD machine,
which is not usually what we mess with.
Okay. I thought he had one machine and
the way he was talking it was like a six
or a seven and he wanted me to clean it
up and make it an eight. Everybody knows
I make him an eight.
So he brings it down. You know, the guy
lives an hour away and I told him I' I'd
already do it, you know, on the phone.
So he brings it down. Remember this is a
350lb pinball machine. He's already got
it in his truck. He brings it down. We
unload it. We bring it in the store
and then I find out that the thing's
already a nine. So, you know, I make him
an eight. He already brought me a nine.
So, that's not really what I do. And
then he added all this stuff. He wanted
brand new this, brand new that, all
this. He wanted new screws and this and
that and the other. And the guy had 30
pinball machines, he said. and he used
to have a guy that did all that type of
work for him, but the guy stopped
calling him back. Long story short, the
guy was a real jerk
and that's why the other guy wouldn't
call him back. The guy he used to get to
clean the pinball machines.
So, that's kind of the story. And I
really wasn't mad. I was just kind of
frustrated with myself that I even got
myself in that situation. I'd already
had the machine in the store and then he
adds all this stuff he wants done. I
could tell the machine was already a
nine and it just sucks working on
something
and you know that the guy is not going
to be happy with it at the end. And
people were saying, "Well, you should be
proud of your work." Well, I'm very
proud of my work. I thought it turned
out amazing. I thought it looked brand
new other than the the cabinet itself
had some water damage, but the playfield
area that I did, I thought it looked
brand new. And of course, he gets here
and he's he's it took him two hours to,
you know, pick it up. He played the
thing for two hours in my store and
everybody's like, "Oh, you know, he's a
paying customer." Well, that's all fine
and well. He did pay me, but you know,
I'd much rather work on something like
this. It just it took twice as long as
it should have.
You know, the thing was already a nine.
So, I I like taking them from like a six
to an eight. You know,
that's just that's just that. And a lot
of times I say it's an eight, but in
reality, sometimes they turn out to be a
nine, but I tell everybody an eight
anyway, just so everybody's happy. In my
opinion, a 10 does not exist. Unless it
just rolled off the factory showroom
floor brand new, it's a 10. But a week
later, it is no longer a 10. I'm sure
it's already got scuffs and stuff on it.
All that to say,
you know, I was kind of using the wrong
word, too. I kept saying picky in the
video. Well, I'm picky about a few
things, too. I'm sure everybody's picky
about a few things, but that guy was a
real jerk
and it just sucked doing that job,
but I did it. I didn't want to I already
told the guy I'd do it over the phone
and I keep my word, you know, so I
cleaned it and did everything that I
said I was going to do.
I feel like that would have been pretty
crappy if the guy drove down here an
hour and, you know, I told him I didn't
want to do the job. I I'd already
committed to do the job on the phone
without seeing it. And that was kind of
my mistake really. I try to do a good
job of weeding out the customers I don't
want.
And every year there's always one or two
jobs that kind of trinkle in that, you
know, I kind of wish I never would have
got involved with. Okay. And the people
who say, you know, the customer is
always right have never ran a business.
That's that's just the way it is. Some
customers you just don't want. I know
that sounds crazy,
but some customers you just don't want.
Anyway, back to the Popeye.
He picked this up in Virginia yesterday.
I really don't know what's wrong with
it. I thought he said something about a
cat kid. He talked to Ronnie. He talked
to Ronnie. All I know is he wants me to
rebuild the monitor. I don't know if it
works or not.
So, let's take off the back door. We'll
plug it in and we'll see how it goes.
They make a few different types of these
uh Nintendo cabinets, too. Um they make
a plywood one
and then they make a particle board one.
And this one is the particle board one.
And the particle board board ones, they
always get chipped up around the edges.
They're just not quite as made quite as
well on the sides. Anyway,
you don't see flathead screws much
anymore. Nobody really uses those.
And look what they got going on with the
marquee light. Come on now. Are you
kidding me?
That don't look like it's doing
anything. Let's try this one.
This one's coming up.
That one stripped. Or is it going to
kind of need two hands? I should
probably be pulling on it at the same
time.
People
are always impressed with my one-handed
abilities here.
Maybe I can pull it now. Let's think
about that.
And I'm right-handed, so this is all
right. There we go. Hey, buddy.
Look at this crap. Then you can't really
even take off the back door. What is
going on here?
That had to go. Oh, I guess they came
through the other end. Can't even take
off the back door. Really?
All right. So, we've got our original
Sano monitor.
We've got our original Nintendo power
supply.
I imagine the board is in there. Yeah,
it's in there.
Power cord looks pretty good. We've got
our
brand new end on the cord here.
Dollar store special.
Let's see if it'll do anything.
Got it plugged in.
Let's hit the switch.
I heard a snap and a crackle.
Oh, I hear it.
Well, it appears to be working,
but the monitor doesn't look all that
great.
That's basically a classic cap kit
problem. Basically, it's got all these
capacitors in there and they dry out
over time
and then you'll start having
these issues. It'll be all smeary and
washed out looking.
But it is up and running. So, it looks
like our board is good and our power
supply is good.
So, we basically just got to worry about
the monitor at this point.
He got me some T- molding here, it looks
like. I wonder if this is the right kind
though
cuz this may be the uh
Yeah. See, this is an offset.
See how the right side is thinner than
the left side?
Takes a specialty molding, but
we'll see what he got here.
I bet it's the regular gun.
Yep. It's the regular gun.
If you put this in there,
just to show you what I'm talking about,
that would look like crap
cuz then this is for the plywood
cabinet.
The particle board cabinet is offset.
Don't ask me why they did that. I don't
know.
Centuri games like Gyrus and stuff has
offset T- molding also,
but this is the wrong T- molding.
And I don't know if anybody makes that
offset T- molding. What I usually do is
I just put a little bit of wider T-
molding on there and it'll it'll hang
off this side just slightly, but it'll
look better than the alternative. How's
that sound?
All right. So,
I guess we're going to start taking that
monitor out. What you think?
So, on a Nintendo cabinet.
It's got this little wing nut here.
Loosen that baby. Slide this back. It's
already slid back, but you slide it back
like that.
And you're supposed to be able to lift
up on this, but somebody's got this
channel on backwards. They always do
that.
It's supposed to be the other way. Let
me get a uh Let's see if this will do
it.
Uh-huh. Didn't think I was going to do
it, did you? First shot.
See how that's got a lip on it?
That's actually supposed to be on the
front
so you can lift up on it
just like a pinball back glass would be.
So now we got that out of there.
And to get the monitor out, there's two
screws on this side.
And there'll be two more over here.
And the power comes down and it plugs in
right here.
One of those is for the uh marquee.
We're going to have to tie in this.
We'll cut this wire and tie it tie it
into the marquee wiring, which is this
white one here.
Won't be no big deal.
And then we've got the little sound
connector,
video connector,
speaker connector.
And once we unravel all this power wire
going down here,
All we got to do is take those four
screws off on the front
and we'll be able to take this whole
monitor out the front side. Okay, let's
do that.
All right.
One screw.
Third spoon.
Three screw.
Four screw.
Then what's very important is you don't
lift with your knees. You lift with your
back in an awkward twisty jerking
motion. Okay?
And we're out.
There she is.
So, now I'm going to go get my
screwdriver and a pair of little snips
and we'll take it all out.
All right. So, I took the monitor board
out of the frame. You're not going to
believe this. I had a whole long video
step by step of how to take this out of
the frame.
I thought I was doing a good job, too. I
had a nice little clip of me discharging
the anode,
telling you exactly how to take it out
of the frame, unscrew this wire, unhook
this wire, fish this through the frame,
yada yada yada. I thought it was great.
I had my tripod all set up real pretty
down on the floor.
showing you from this angle. Then I
moved it over here to this angle. Then I
was showing you about the little clips
that hold the board in. I thought it was
gonna be great.
Went to watch the video back and somehow
I had my camera set on slow motion.
So there went that.
But I got the monitor out
and now we're going to change all these
capacitors.
One by one.
How loosey goosey this one is.
Yeah, that one wasn't even connected. I
don't think
see it.
But anyway,
take the cap out one at a time.
Find what value it is over here. This is
my little cap drawer. I've got one
I say UF, one UF, 2 UF, 3 UF,
4.7,
10, you know, all the way down to 2200,
all different sizes.
And some people always wonder why Ronnie
always says microfarad.
real weird like that is because we had
people always saying that was the
correct way to say it. We say UF,
but all the other people online call
them microfarad.
Now, I want you guys to look at this
capacitor
and see what that says after the 2200.
That sure looks like a U and an F to me.
And every cap has that written on it. So
I've always just say 2200 UF, 10 UF, 2.2
UF. That's just the way I've always done
it.
But all the people online that have
probably never capped a monitor in their
life
insists because they've seen somebody
else do stuff
that it's microfarad.
Okay. So, that's the story behind that.
So, anyway, go ahead and cap all this
and we'll put it back in there.
All right. I got all the caps changed.
Check this one out.
This was C471
and it basically fell out in my hand.
The positive lead
disintegrated.
But
I got all the capacitors changed.
We're going to put it back in the
monitor frame.
And we're also going to do the sound
amp. If you've got one of these Sanuel
monitors and you're rebuilding it and
changing the capacitors, make sure you
change the caps on the sound amp because
it's time. It's over 40 years old. The
sound seemed like it was working okay on
that Popeye, but it's just a ticking
tomb bomb. You need to take that sound
amp out of there. Change those caps
while you're at it.
All right.
So, here's the sound amp. I'm going go
ahead and take it out and get it out of
the way.
Just need to change all those capacitors
on there.
I'll do that in a few minutes.
And then you fish the power wire back
through
like so.
Try not to knock over your drink.
You put the next board up in there. Get
it kind of out of the way.
Hook your yolk wires up out of the way.
Lots of wires you kind of got to fish in
there.
And then I always put the left corner
in. There's a little notch that's got to
sit in.
And then you try to line up all of your
little
standup
things. I've got it all tangled up right
now, of course, cuz I'm recording it.
There we go.
All right. You line it up. Make sure
it's on the little tabies.
Push down till it snaps in there. Wham.
Bam.
Then I'm going go ahead and hook up my
anode.
If you didn't see that shadow pinball
video I was talking about,
it got a lot of views. It's a shame that
you have to I will admit we we blew it a
little bit out of proportion on purpose
to get more views. I'm just going to
come clean. It wasn't quite as big of a
deal as it sounded.
But unfortunately, if you put a negative
twist on something, you get more views.
You know, that's just how it goes. Like
if you watch that video where the cop
showed up when I was trying to buy some
arcade games,
it got a heck of a lot more views than
anything else.
Put my neck board on.
I'm going to hook up my yolk.
I can see
Go.
Hook up my ground
screw here.
Push the wires back through. Try to get
them looking pretty again.
And there's usually a screw on the
bottom.
of the chassis. Also, right here in the
back corner, right by the flyback.
Don't forget your ground wire for the
neck board.
There's a little hole in the neck board
you have to loop it through.
I guess you don't have to, but that's
the way it was from the factory.
Got to get your wires and little
holders. They look all nice and pretty.
And I like to run my power wire behind
this post.
so it doesn't get over here and mess
with these knobs.
Hook in your the gouge ring.
And there's these little clips that's
supposed to
slide in these pins here to make sure
the board don't fall out.
Not that it really can.
There you go.
So, we're basically all hooked back up.
We got to cap this sound amp. And then
we'll put that back in.
And make sure you hook these up right.
This is called JB.
And there's a JC
JC. And you got to make sure you plug JC
into the right connector. You can
actually get these reversed
and it'll cause you all kinds of
problems. I've never had that issue
because
to me it's kind of hard to plug them in
backwards, but apparently people plug
them in backwards all the time and it
messes up all the sound on the game
board. It'll fry your sound basically if
you plug this in backwards on the game
board itself.
So, I'm going to go cap this. I'm going
to come back, hook it all back in, and
then we're going to put it back in the
machine and hopefully we've got a better
looking Popeye.
All right, we're ready to put the
monitor back in.
Remember to lift with your back.
All right. Are we confident enough to
just go ahead and screw it in before we
even try it?
It would probably be the smart thing
to test it first,
but I'm not going to do that.
Put the screws back in.
Light de
All right, all four screws are in.
Let's carry you guys around to the back.
And get you set up here.
We're going down.
I'm going to tilt a little bit. Think
about that.
All right. So, then we'll get the power
unraveled.
We throw that down in the bottom like
so.
Then we fish our video out.
And we're going to snap it back into
this Molex connector
like so.
Can't go that way. You're over there.
Then we're going to get this little
video, this little uh sound connector
here.
Get my T- molding out of the way.
I feel like this live action here.
All right.
I should have left that on the board,
but oh well.
Snap that in there. So now I can plug
this baby in here.
Boom.
All right. All right. So then I like to
do a once over.
I like to make sure I've got my yolk
plugged in. I've got my ground plugged
in. I've got my anode plugged in. I got
my video plugged in.
And I forgot to plug in the speaker
here.
Typically don't have the speaker hooked
up to the monitor, but on a Nintendo you
do. Now we're going to plug the monitor
in.
We're going to turn the game on.
What happened?
I think the game might have already been
on.
What did you guys do?
There was a bad There was a bad
connection down there on the cord.
Scared me a little bit.
I was thinking, uhoh, I'm going to look
like an idiot. Not that that's anything
new.
Boom. Shaka locker.
Go up a little bit so you guys can see.
Might back out a little bit. Yeah, there
you go.
Well, that's done. Now what? Give me the
money. Put the money in my hand.
See, this is the type of repairs that I
like to do.
Today's actually Sunday. I'm supposed to
be off today, but you know, this is
almost relaxing to me to come in and get
this monitor going. Gets me ahead of the
game for the week. Now I can call
Trevor, tell him to bring me my money.
It's a little too bright.
Let's see here.
What' that do? That get it right. Lower
it.
Got to get my mirror probably.
Uhhuh. That'll probably work.
I'm not really sure what's going on with
that marquee light because it's not
plugged in.
I mean, the marquee lights plugged in,
the original one, but they've got some
kind of wire hanging out the back. I
wonder what's going on in here.
Everything seems to be fine. Somebody's
added another LED
light fixture that I don't even think it
needs.
We'll take that out of there,
Trevor. I'm taking it out. I mean, it's
got the original setup in there. There's
no need for this little Chinese piece of
junk here. Okay,
that's how it's going to be.
unplug it here and pull it through.
That was extra. We didn't need that.
Put the screws back in.
Well, we fixed the marquee. We fixed the
monitor.
I guess I'll get a little Windex. Wipe
it down a little bit.
I don't know if it's coming up on
camera, but the monitor jumps up and
down just ever so slightly.
Believe it or not, every Nintendo
monitor does that after you cap it.
That's just how it is.
Nothing I can do about it.
Not a big deal.
Let's see if I can swap the bracket on
that uh monitor bezel.
It's on there pretty good.
Let's see.
I'm basically trying to get this bracket
off so I can turn it around the other
way
without breaking for the plexiglass.
Well, that didn't work. So, we're going
to have to heat it up with a heat gun.
All right, I got my bezel on there.
Starting to look pretty good. I got the
bracket swapped around, obviously. Got
it on there.
Now, it's T- molding time.
demolding time in the auction barn.
We used to go to auctions all the time
and they'd have these grab bags and
every time they sold grab bags, grab bag
time.
Grab bag time in the auction barn.
Molding time. Auction barn.
Wham bam. Here we go. Isn't it exciting?
There's that.
Did anybody see? Oh, there we go. Let's
say who took my razor blade.
Sometimes you have to glue this in.
We'll see how it goes. Hopefully, it'll
just go in like it's supposed to.
So far so good.
You take your razor blade and you got to
cut the barb off the back of it around
your corners.
and obviously you pound it in with the
mallet.
Cut the barb off again around that
corner.
Got it about there.
Cut the bar off for about there.
That's one side.
You kind of roll it under. make it look
real pretty.
And just to make it a little
complicated, it doesn't really matter to
me,
but the uh the control panel takes the
regular T- motor,
just enough to make you have to order
two different types.
Cut
that off.
Top of the line.
Didn't really like that part.
Perfect.
Perfect people. Perfect.
Pick up some of my mess here.
Well, it looks pretty good. Somebody put
a new sticker on there already.
All right, we'll have a look.
Have a look. See,
looks pretty good.
Nintendo, they make some of the best
cabinets. Donkey Kong, Donkey Kong Jr.,
Popeye,
Play Choice, all that good stuff.
T- motoring always really really sets
them off.
You may be asking yourself, well, Joe,
what's going on with that blue back
there?
Well, obviously somebody was trying to
hide some of the chips on the back, but
Trevor is actually pretty good at
painting.
He's an artist, you might say.
And I'm going to leave that for him to
do. I think he can get it good. He can
probably do better job at it than I can,
actually.
I mean, I don't know what they they were
thinking, though. The the color match
wasn't even close. Come on now.
But once it gets that cleaned up, this
be a pretty nice machine.
Look at that monitor.
How nice. Look how bright. Look how
vivid. Look at the colors.
I'm going to leave that uh Novelty
Vending on there. He may actually want
that on there.
Niagara Falls, New York. doesn't have a
area code on it either.
But let's see if we can play a game. See
if everything works on it. The buttons
and such.
All right, let's see these here.
I'm not even good at Popeye, so you
know, don't expect too much.
I'm the repair man. I'm not the player.
People always think you're supposed to
be really good at arcade games if you
work on arcade games, but me and Ronnie
enjoy fixing them. We don't really enjoy
playing them that much.
I don't know. It's more fun to me to fix
it,
if that makes any sense.
Oh, come on. I thought he was going to
go over and then I was going to hit the
punching bag.
I don't really even remember how to
play.
I thought I was just trying to get the
hearts.
That didn't work.
I think I'm trying to get him trapped,
but he's got to be in just the right
spot.
Totally missed that.
I ran out of time.
All the world's mad at me.
Oh, yeah. I forgot I can go this way.
Okay, I see.
Right into
is that Brutus?
He's got two names. Brutus and what was
the other one?
Guess I'll try to trap him.
This is pretty pathetic so far.
How sad is that? I couldn't even get
past the first level.
I played this game a year or so ago and
I got to the third or fourth board,
but now I don't even remember how to do
it.
Do the hearts give me more time?
I don't want to miss it.
Can I hit him now? Bam.
Trevor's probably real good at it.
Missed it again.
I think I should have just ended the
video before I even did the game play.
Yep, definitely should have ended the
video before I did the game play.
I'd like to beat the first board.
Damn, missed them.
I just get all the hearts. Is that the
whole point?
All you got to do is get the hearts.
I've been trying to get him trapped.
That was bad.
All right, let's see if I can do better
now that I know that I'm not even
supposed to be trapping him.
It's a lot easier when you know how to
when you realize the whole point of the
game. There he is.
Hold on.
pitiful.
Pitiful
seems to be working good though. I'm not
any good at it, but everything is
working.
Hold on.
I almost made it.
Uh oh.
Game over, probably.
Yep.
Well, anyway,
got it finished up. Got it off the to-do
list. Wham bam. There we go. We're going
to make that money. I'm all about making
that money.
turned out pretty good. I like these
Nintendo cabinets.
Worked on a bunch of those Sano
monitors.
Anyway, thanks everybody for watching.
We appreciate it. And thanks everybody
that's been using our Amazon links. I
haven't mentioned that in a while, but
if you don't know about that,
there's a link down below this video if
you hit the description button. There's
an Amazon link there. And if you click
that link before you buy anything on
Amazon,
it actually gives us a tip for sending
you there. And it doesn't cost you
anymore. So if you buy something on
there for $20,
it still cost you $20,
but Amazon gives us 50 cents or
something like that for sending you
there,
which doesn't sound like that much, but
at the end of the month, it actually
adds up to quite a bit.
And some people have it bookmarked
and you know lots of people order tons
of stuff on Amazon especially this time
of year around Christmas. So we
appreciate everybody that's been doing
that. And we've also got uh a Patreon
channel now that people have been
subscribing to. So that really helps us
too. And thank you for everybody that's
been doing that. We had somebody visit
last week that is a Patreon supporter
and that was pretty cool. But anyway,
thanks everybody for watching.