Building the Catalina Wherry - Part 58 - So close to done!

Nomad Boatbuilding
98 followers
261 Video Views·Aug 25, 2024
n
this is looking good I am happy with this my taping came out pretty nice nice and
clean certainly any any little nural that might be there and there's really none to speak of except a
couple of the tiniest tiniest ones uh you know they don't stand out what I want to do now is
tape off my for my rub rails again so I'm just going to run tape along the hall sides because I
need to continue with some varnish on the on the rub rails so while it's inverted we'll tape off
we'll get a couple of coats just on this bottom Edge is my plan maybe we'll wrap it around the
side because more more varnish on the rub rails the better we'll give the bottom a coat of oil
and um and then we'll that'll basically prep us for flipping this back over and then once it's
flipped over all I need to do is finish out a few more coats of varnish on the uh the whole gunnel
structure and then we're done you know just assembly so that's what's G to happen right
now now I've uh given this overnight to dry after cuz I did my my finished coats on here yesterday
I wanted to give the all that paint time to dry before I wouldn't put tape on it and that's also
why I peeled off the um peel this off because if you don't want any sort of wet paint That's
lingering right at that tape Edge to necessarily be interrupting your next coat especially when I'm
making a switch from waterbased back to solvent based it's really not water-based we need to make
a distinction there so water-based paint would be like water colors or gouache uh these are paints
that require the presence of water for them to be liquid but water born paint which is what this is
is the pigment is suspended in plastic resin and that's used us a High Vol highly volatile
solvent to keep it liquid and then it's using water as a major carrier so we use a very small
amount of higher volatility solvent to keep that plastic liquefied the water is just a carrier it's
all sort of immersed in the water and then the water evaporates and then that solvent
evaporates after the water's gone I'm having a time with my masking tapes lately for the first
few feet just wants to tear on me coming up like that coming off the roll I don't know
what the deal is it's like every roll I've gotten from my local hardware store has been like that
lately so very
frustrating okay now I don't need to worry about coming right right down the line I purposely
brought the paint down onto the just the inside corner of the rub rail on purpose cuz it looks
better but when I go to tape this up it's fine if I let that little inside corner
show I'm this taping is more just to keep me from accidentally hitting the hull with my paintbrush
okay now I like to use just the corner of a plastic squeegee to put a little bit of
pressure on that lower Edge that contact Edge just to make sure it's got a tight
fit we also want to rub this down with some Scotch right
in order to uh scuff up that surface a little bit before we start applying varnish onto it and so
I don't want to hit my hole with that either so that's why we're doing the taping as well
I'll also tape off here just along this guy we're just going to use linseed oil on the uh
on the bottom planking and this is really just to keep oil from bleeding down onto my paint as well
it's faster to tape than to have to try and slow down and and freehand cut that edge especially
since the oil is a little bit on the thin side there's a little paint exposed above
the tape not a big deal you can always just come along with a cloth and wipe back back we in fact
we are going to wipe back the oil so it's not going to sit back sit down there on that edge
really okay let's put a coat of something on the bottom here decided to just keep this real simple
we're just going to go straight plain old linseed oil got it cut down to some solvent about 50%
maybe here we go
this will soak in pretty good I'll probably give it a second coat a
little bit later on maybe even a third we'll see see how the day
goes got to love the way linseed oil will bring some something to light and
there isas I'm not using any like osmo or any sort of name branded stuff here
this is really just to keep the wood keep the wood alive it's not not gunning for a
fine finish this is basically going to get the Daylights beat out of it after
all I want to go use some boat sauce on this instead but my jug of boat
sauce is all gelled up I really can't be bothered wking around making another
batch got things to do today this will be fine boat sauce is a shop made mixture of
linseed oil turpentine and pinear linseed oil comes in two varieties raw and boiled
in its raw form if prepared properly it's actually edible and we call it flax seed
oil boiled linseed oil has had chemical dryers added to it and historically this
required boiling in order for them to be combined modern linseed oil this is
no longer required but the name boiled linseed oil Still Remains as a way to differentiate it
from the raw exactly what I didn't want to have happen right there there a nice
little just going to do this just run down the side and make sure we're not leaving any dribbles
okay now we're just going to get a couple coats on here before we uh flip it
over if I haven't mentioned it round brushes work better on small contoured things if I
were using a flat brush right now I'd have to be doing like this to try and get it to
take to that contoured surface I don't know why but I just know that this works
better the idea here is by uh work the gunnels from two different sides like this I'm going
to get extra coats on the face of the gunnel so this first coat breaks at this corner the
second coat when we flip it over is going to break at this corner I mean I'll try and wrap
up underneath it a little bit but I'm not going to knock myself out trying to get right to the
inside face here because the corner will mask the um the break in the brush strokes but the
result is going to be that we're going to get more coats on this surface that will take more
abuse so the one thing I've learned the hard way about doing stem bands is you generally want to
try and pre- bend it to your shape as much as you can and you want to leave it just uh sprung
a little bit straighter than your curve and the other thing you want to do is before you do that
you want to drill as many holes as possible if you got any real tight bends don't drill any but do
your Center punching first and anywhere else you can do very small pilot holes but you're better
off leaving them small in fact the best thing to do is drill pilot holes that are the that are the
diameter of the Fastener the core diameter of the Fastener you want so the the hole the size of the
hole that you want the screw to go into into and you could even bend it all get it in place and
then uh drill through those holes to get your your Fastener locations which is a smart way to
go but if you try and open them up and do your counter scking all at once the chances of you
getting making them the stem band Kink get those holes is really really high so the only thing I
found that allows me to do that even Clos is to use a a u a Rolling Mill I've got sort of a small
Rolling Mill that is just barely big enough to take this and I put a piece of melamine against
the show face so that it doesn't get messed up by the knurled knobs on the the Rolling Mill
anyway I'm going to use a center finder here to drill my holes do them one at a time to start
dip these in a bit of wax or something when I put them in now you want to do a really pretty
job use slotted screws but problema slotted screws is you got only one orientation where
they look good and that's when the slots lined up and any other orientation you look terrible
and you got to go 180° sometimes to fix them or close to it I'm I'm going just going to use
Robertson screws here where even all I got to do is a quarter turn to try and get them
to square up in one way so I can either make diamonds or just trangle Square we'll see how
that works so I drill and screw one at a time because it's adding tension to this as we go
up I'm not bothering with Bing compound for the very reason that this is all painted so
it's not really
necessary the paint basically acts like a bedding compound my favorite hardware store
alternative to traditional bedding compound for putting underneath Hardware stem bands
and small parts like that is common plumbers putty I'm also using bronze screws rather
than brass screws even though this is a brass stem band um bronze is just a better fastener
brass Fasteners are always a little on the weak side even if you find good ones
and the last thing I want is for my customer to be dealing with a broken
screw because he decided to take the stem band off
to paint or something like that so at least the bronze will stand up better
to the elements over the lifetime of the boat I only use brass Fasteners
on on boats that are primarily used in fresh water and even then I mostly just
use them on parts that remain out of the water I never used them below the water
line oh it's so satisfying getting to this stage I tell
you this is the last thing I need to do in order to flip the boat
over you can tell right now this guy to straighten out just a hair it's the
hard part trying to straighten it out without kinking it at
the fastening hole
sometimes what you need to do is you just find that high
hump a few good wraps and you see if you can't get it to sort of yeah there we go that looks
better changes up the shape a little bit
f done right and the tension you have in the brass keeps
it tucked nice and tight against the face of the
stem don't underestimate how long it'll take you to install one of these two this
is looking fast but it's only because there's quite a bit of preparation ahead of time
always remember to flag off your drill bit for depth because this is exactly
when you get cocky and then go drill a hole right through your
boat
beautiful okay we got a coat of oil on the bottom we got stem bands on final paint on the hall we
got a couple Co extra coats uh three extra coats on the bottom of the rub rails that we know that
those are done I don't have to worry about working all the way around to the planking we are ready
to flip this over and do the last few items on the list which is putting some more varnish on the rub
rails and the deck structure and putting in the uh lashing rail for the gear and the thwart Riser
and dropping the thwarts in I still need to make couple of bolts to hold the thwarts in place but
we won't worry about that for the moment uh let's go this is exciting get some cam straps going
here the right orientation yep
get that started at the other end
that's go what's going on with this got a jam up jam up why are you
jammed there we
go h last thing you need when you're trying to be
productive it's not always the
way there we go that's
better no maybe not this is a janky
clamp all right move that
there yeah the sounds are making me nervous too okay all right we're
pulling this one out of commission don't know what's going on with that
but my other ones my ones that I like to use for this I didn't make these the clearance
in these pulley big enough to slip the hook through easily it jams up and so I've not using
those probably need to have like a dedicated set
of clamps for lifting that don't have hooks on them
okay there we go back in
Action so what I'm going to do just like before I'll roll the dolly out of here no
wi roll the dolly out of here for the lift
lift for the
roll am I not enough room in this shop ever you wanted to roll are you
okay not the usual controlled roll I
like suddenly afraid of these clamps scaring up my planking
okay there we go woo
okay looks like I could stand to get these hoisted up
higher let's do this
oh I hate these things hate these
things okay let's
see and we're over there's always one stupid insignificant detail that like holds you up for
a full day this is it just a little munch on the nose here which is going to take 20 steps to fix
probably with the boat flipped back over all we need to do now is add a few bits
and pieces that are waiting in the wings and then it's ready to go into the hands
of our customer Joe I hope you join me for that next time and building the Catal wary
