They Stole Every Tube Out Of This Westinghouse Radio... Now We Have To Find Replacements...

Amateur Repair Time
257 followers
1.2K Video Views·Oct 12, 2025
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time. If you haven't been following the
saga of this Westinghouse radio, I bought this at the flea market for $10.
It's pretty big actually. It's just an old plastic,
what do they call it? I can't remember the name of the material, but Bakelite. Somebody said it
was Bakelite. I don't know if it actually is, but just an old plastic tube radio. AMFM Westinghouse
from the early 40s it appears. Early 40s? I've got the schematics right here. Let's see when
this sucker's from. We've been working on it, and on our last video, we got her up and running.
Well, not running. We got the power supply up and running. It's an H307T7. This thing is so simple,
it doesn't even have a pilot light on it. It was probably about the cheapest AMFM you could get.
On the last video, we tested, and this selenium rectifier is actually still working. We did
all of the caps. We did all of the resistors that were out of spec, and the selenium rectifier is
actually still working. We're going to swap it out, but I want to put the tubes in it and get
the thing playing first so I can properly measure the voltage with a load. I don't know if that
matters or not on these, but we'll see. So I need to look through my tubes and see if I've got any
of these. When I bought it, all the tubes were missing. I think somebody thought they pulled a
fast one on us. We'll show them. We'll keep all of these tubes that are worth a couple bucks apiece.
Maybe, if anybody actually wanted them. Right, so that's where we're at. So we did all the
capacitors. I'll show you that. You got to watch the other video if you want to see that.
Several of the resistors are out of spec. Replaced several of the resistors.
Brought it up on a Variac with an amp meter. Checked everything. There's no shorts or anything,
and up until at least the power supply, the voltage is proper. So again, tube time.
I was thinking, wouldn't it be cool if I could just do a couple tubes at a time? And as I went
along, I could just, like if I put in the output tube, maybe I could see if we could get a hum out
of it with just the output tube in. And maybe I could leave the FM tubes out and just do the AM
tubes. Because some of them, it seems like, only are for FM. Some of them. Somewhere. But that
won't work because it's a string set, of course. So without all of the tubes installed, the power
string is broken and the filaments won't light up. So I forgot about that. So we can't do that.
So I'm just going to have to find all of these tubes one by one, put all seven of them in,
and then see if the thing will come up. So that's what we're going to do first.
So I need a 50C5. I'm already, the very first one I can't read.
Let's see if it's on our parts list a little easier.
Of course not. Why would they? Because it says it on the other one.
Okay, yeah, it does say it up here. Okay. So I need a 50C5, a 12BA6, a 6BJ6, a 12AL5, a 12AV6,
a 12AT7, and a 12BE6. I know I've got the 50C5. The other ones, I'm pretty sure I got the 12AT7.
The other ones, I'm not so sure about. I've done several tube radios. I'm trying to fill up my
shelves here. I've done several tube radios, if you haven't watched on the channel. That Silver
Tone might be my favorite one that I did. That was cool. That was so cool. So I've been in this
area before, of course, but I don't have all of the numbers memorized. So I'm not sure what I've
got. I do have a ton of tubes though. So let me go see what I can find and we'll see if I can get
all seven of those or if I need to order some. All right, folks. So I was able to find all of
the tubes but one. One of the tubes was elusive and I have ordered it. It will be here before
the end of the videos. Don't worry about it. And you experts, I'll let you guess which one of the
seven tubes I did not have. So first up, we have a Westinghouse branded actually 50C5.
Boy, it's a... which would be the output tube. It's kind of smoky looking. I don't know if this
one will be good or not, but let's see. Nothing. Let me wiggle it in the socket. Damn. What am I
doing wrong? It's gotta be a socket thing, doesn't it? I want to clean the legs on it.
All right. Well, the other one, no matter how I cleaned it, it wouldn't test. So
I don't know if it was actually fault or if it's just I didn't have the pins right or whatever,
but this one seems all right and it's a Westinghouse. Now on this particular tester,
I hardly get anything that goes above about the 70 there. So that's about as strong as they get
on this tester. This thing probably needed calibrated 20 years ago. So that counts as good
to me. So I'm going to clean up the actual metal on the chassis a little bit and go ahead and
install that one and then we'll move on to the next tube. Okay, so I wiped the chassis down a
little bit, got all the dust off of it or most of the dust off of it. Very carefully cleaned the
speaker. I haven't punctured it yet, so that's good. And that is the socket for the 50C5 and
the replacement one I found, by the way, was a Westinghouse branded one. Now I don't think I've
got a Westinghouse branded each one of them and it doesn't really matter, but you know, if you can
do it, why not, right? I feel like I'm completing it. You know, I'm putting the Westinghouse tube
back in the Westinghouse. This is probably the actual radio that it came out of
in like Illinois or something back in the day. And then the tube went to California and the
radio stayed in Illinois for a while and then went to Texas. And then came from Texas back to
Salisbury, North Carolina where I bought it. And then the tube was, you know, it somehow made it
down to Rock Hill. When I got all those tubes, didn't the guy tell me that he had just moved
down here from up north? That they're getting reunited again. All right, that'll be a prelude
to my theme song at the end of the video today. Okay, so that's the first one. Let's move on to
the next one. Next up, we have a Westinghouse branded 12BE6, which is the AM converter FM
oscillator tube. I've never even heard of it. I mean, I've heard of those tubes, but I've never
heard of a 12BE6. Let me try another one. Just see if I've got one better, but I don't like it.
Like I said, I think the whole thing's skews low, but you still don't want to see it in the red.
All right, so I've got four different ones. They all test kind of similar. This is a clean looking
Westinghouse again, and it tests a little higher than the others, so we'll go with that.
Yeah, I'm just going to assume my calibration is way off, and in certain tubes it's
more obvious than others. So this is a 12AT7, but unfortunately it's got a short in it in the
connection to the heater. If you screw around with it, you can get it to glow really bright,
and I've been cleaning the pins, and checking the socket, and bending the pins, and all that.
Sometimes it'll come up very nice and bright, and sometimes it's like this, and you can just
you can watch it kind of blink back and forth. So when it's like this, it's dim,
and it doesn't test very well, and I can't get it at full voltage enough to check it like that.
So there's just some kind of issue with that. All right, so my 12AT7, I had about a dozen
different ones. I didn't have any more Westinghouse ones that were any good, and most of them weren't
that good, but I did get one that tested somewhat decent and put it in it. So now we're up to a 12BA6,
and I've got six of them that I could find. They're all used though, but really,
you know, even the ones that are new or old stock, there's no guarantee they work.
You kind of got to test any of them, and I'm not super confident in my tester. It's about time to
calibrate it, I think. That'll be its own video, I guess. Let's see what this one does.
Hey, it's barely in the good. That's pretty good for me.
All right, so we got a 12BA6. Now that only leaves us, that's the fourth tube,
so that only leaves us three more. We're getting there. Next up is a 12AV6, and I only found one
of these so far. I didn't look in my secret stash of new ones, but going through some,
and again, I've got so many of them, it's hard to even keep them all straight, but
I did find this one, so let's see, and you know, it's the IF, let's see what they are actually
calling this. They refer to this as the AM detector AVC audio. I don't know why they would
say audio, but whatever. So that's what that is. So this is the first side of it, I guess,
and it's test button one. Come on, baby, I only got one of you. Oh, hell no, that ain't gonna work.
Look at that. Look what it did. Oh, no. Oh, boy, I got a five and a 12AV6. That one sucks,
and that's just one side. The other side is probably even worse. Let's see, we'll get rid of
that. CABF. I'm setting it up like the chart says. Get rid of this F. AA. Oh, wait a minute.
Nope. Yeah, that's right. AB. Let me double check. 12AV6. So the first one's down, then it's
CABF. Skip one. All the rest of them are down. Oh, there's three sides to it. Off, B, and one.
Okay, so this is the second side of the 12AV6. Pretty crappy. Oh, and I even had the sensitivity
too high, which is going to make it even worse whenever you turn that down. This one ain't no
good. CAB. So now we'll test the final one. FB1. It's the third part. It's at least close to
passable. All right, so let me see if I can find any more 12AV6s. All right, so I found a GE that
looks nice. Let's see. It's not glowing very bright. I guess that doesn't really matter.
So, well, I guess we'll do it backwards since we've already changed all the settings.
Test button one. They're all test button one. So this is the third part of it.
Bam. Look at that. Full swing. All right. Change that back. Make sure I got that right. CABF.
Okay, let's try the second part of it. Bam. Full swing. All right. E, C, A, B,
F, A, A. So I'm setting all of these knobs based on what it's telling me here.
The 12AV6. I'm going to turn the sensitivity back up to 91.
All right, so here's the part that just barely moved on us. Oh, it was horrible. There we go.
There we are. Much better. Okay, so that goes out to all of y'all. I keep getting all of these
people saying, you know, so they watch my video and it's called amateur repair time. So they
assume that I've never touched on one. I've never, I've never worked on one and I don't know
anything about it. And so they'll say, you know, and I just caught my one video and they'll say,
oh, it's never the tube. Check your caps and your resistor. Well, the hell it ain't never.
Sometimes it is the tube. Like that tube there would not be performing anywhere near how it's
supposed to perform. Would it work? Maybe. But I get them all the time where the tube's completely
dead. It's not doing crap. Or you get them like that where it's barely working. You saw I tested
it on all three parts and it's just, it's not, it's not working right. So sometimes, yes, it is
the tube. Definitely. Tubes definitely wear out. All right, so I'm gonna pop that one in. We're
on to the next one. All right, so this one is a 6BJ1. Um, no, 6B, well, I'm lost. 6BJ6. It's a 6BJ6.
I thought that didn't sound right. Uh, which is a very simple one apparently. Uh, so some of them,
you don't really set anything. You just put it in the right socket. You put the right, uh,
sensitivity on it. Uh, you set the voltage correctly. You turn off all of the, all of the,
uh, pins basically. And you just test it with test button one. I guess it's just checking
emission a little bit or something. It's, it's checking dynamic mutual conductance, right?
I'll take it. Good enough for me. It's in the middle. You know, it's, it's, it's questionable,
but I think the meter is questionable. So, um, all right. So that one's that one. We're down to
our final tube that we need. So I had to order this one. This is the one I had to order. Some
of you probably could tell which one I needed to order before I did it. Okay. So the one I did not
have was the 12AL5, which is a little tiny, a little tiny tube. It's like this big. Um,
which I've never seen before, but, uh, so I had to order them and I made sure that the ones I
ordered, at least some of them were Westinghouse. So I think we ended up with three Westinghouse
tubes in it and four that aren't. Uh, look folks, that was about the best I could do. I at least
gave it a good effort, right? So I'm going to test one of these just to make sure it's all right.
And then we'll pop it in. All right. So it has two parts to it. Okay. Look how cool you can't
it's a little short stack. All right. So, uh, 12AL5, I've got it set up. We're supposed to
test with test button one, both parts. Ah, that's good. So that side must just be a, you know,
you know, I did hear, well, I was reading up about them because you can get the 6AL5s and
I've got a bunch of those, the 12AL5s you just don't see as much. Uh, and it's the exact same
that's just the 6AL5 runs off the six volts, the 12AL5 runs off 12 volts. And they were saying
that you could probably replace it with just two diodes, just put them in the socket. But, uh,
I'd rather not, if I can not do that. So if you look, you know, and part of the reason I do this
stuff is because I'm trying to learn hands on. It's one thing to read or to have people tell you,
you know, but if random people on the internet are just telling me stuff, I don't learn from
that. Like I just, I don't even know who they are or if they know what they're doing. I mean,
I assume they do, but I rarely have people explain things to me. They just, usually they come across
in a, in a, uh, know it all, you know, a know it all way and just say, don't do it like that.
Do it like this. And they don't tell you why. They just say, that's how everybody else does
it. Well, I don't do anything because everybody else does it. Uh, you know, I learned about
lemmings a long time ago. So 12AL5, if you look what these are doing, so you've got your heater
voltage is 12 and then they're telling you the sensitivity to set it at. Um, and then, uh,
they're telling you to use socket 30 and then there are two listings for it and they don't
change the heater, the heater voltage or the socket. So, you know, you leave that the same.
Why they printed 62 twice, I don't know, but they just seem to do that for all the sensitivity.
So on the first one, we set three and four to A and B. I think the, well, let's see here.
If you'll notice on most of these, they don't go past like
here on the ones that we've been doing. I think those are actually the pin numbers on the sockets.
Right. And so some of the sockets don't have 12 pins. So you wouldn't ever need to change 12
things. If you look at this 12AL11, it would tell you to use socket 23.
And then it does have a switch for each one of the, of all 12 of those, uh, switches. So let's
see if socket 23 has 12 pins on it. It does. Or 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12. Okay.
So we are using socket 30 because it's a smaller tube. So it's only got like eight pins on it or
whatever it is, seven or eight. So these switches, depending on what position you put them in,
they do different things. And if you notice, every time there's one with, with two things
that you have to test, there's a couple of them that you don't change. That's because those are
the pins, uh, that are providing power to the, uh, filament. That's what makes it glow. That's
what's giving it the 12 volts. So on a socket 30, which we're using, 3 and 4, you set on A, B,
because they're, they're saying, you know, I guess the A position is the first filament string
and the B position is the second filament string. So if that's true, you would never see one with
more than, uh, two, one thing set on A or B. Does that make sense? So they're saying,
use socket 30 and then put number 2, pin 2 on F and 3 and 4, the two we're concerned with,
put 3 on A and put 4 on B. And look, nothing else is B and nothing else is A. It's because A is one
of the filaments and B is the other side of the voltage to the filaments. Now over here,
these are different. Um, so it's, it's just these first 12, right? So if that's true,
because the reason I'm saying that is because I know that pins 3 and 4 are the two filament
voltages. So if that's true, you'll never see something with A on more than one pin
or B on more than one pin because they never make tubes like that. Um, and if you look here,
it actually shows you that the filament string runs through pins 4 and 3, 4, 3, 4, 3.
So the 12, uh, AL5 is the last one there. It's kind of hard to read this. It's the last one
there. And the filament voltage is 3 and 4. So if we look through here, every time it says A or B,
that's the filament voltage for that tube. So A, B, A, B, A, B, A, B, A, B, A, B, A, B, A, B.
Um, see on this one, they've got C in two different places. So whatever C is, it must be
something that can go a couple of different places, but A is only in one place and B is only
in one place because that's your filament voltage. And it stays the same each time because the
filament doesn't change. Um, they're just changing the other, sending the voltages around to other
pins to check different components of the tube. So that's pretty cool. Figured that out. You learn,
I'm learning a little bit. Okay. So, uh, did we test it? I can't remember. I think we did, right?
Yeah, so it's good. And then we need to do the second setup. So the second setup
is C blank, A, B, blank, blank, F. C blank, A, B, blank, blank, F.
Now, the filament didn't go out there when I did that, did it?
Let's try screwing around with it. Yeah, there we go. So I just turned off three and the filament
went dark. If I turn off four, the filament goes out. Yeah, cool. Well, that's how that works,
I guess. All right. Well, I learned a little bit. I mean, I probably would have thought of that if
I just sat around and thought about it a little bit, but I never gave it much thought. I knew
that these were just sending voltages to different places, but I just figured out that A
and B are your filament voltages. Okay, cool. So my whole point is this tube, like I said,
they were saying online, you could probably replace it with two diodes. So if we look at
the schematics for the 12AL5, and we're going to find it. There it is. Yeah, look, it's just two
diodes, basically. An anode and a cathode and an anode and a cathode. Would that be a good way to
put it? So you could probably get away with two solid state diodes, but it's going to change
certain things like just all kinds of like amperage and how many volts get through it and
noise and stuff like that. So I would rather just use the tube if I can. So I went ahead and ordered
them. But since it's basically the two of the same thing, you can tell what they're doing by
looking at the chart. So they're leaving A and B the same both times. You have to test it twice.
They're leaving A and B the same both times because that's your filament voltage. It doesn't
change. But the first time they're saying, hey, make pin 2 F and make pin 5 C. And then the next
time they're saying, hey, turn that off and make pin 7 F and make pin 1 C. So they're saying test
pins 1, 2, 5, and 7, right? Can we see on our schematics here? 1, 2, 5, and 7. So one time they're
using 2 and 5 and checking that connection. And then they're saying, hey, you got to do it again.
And I'm telling you to change a couple things around so that they can test that connection.
And they leave the filament voltages the same. So one side we know works. Let's see if the other
side works. It does. Cool. All right. So that probably is a new old stock tube. We'll slide
it in the radio. And that's it. We got seven, I believe, working tubes. All right. So we've got
them all mounted in. There's the 12AL5. So I have three goals. First goal, I want to watch the
amp meter. I would like to see it use a little bit of power, but not a lot of power. I wonder if
we could figure out the wattage. Does it tell us the wattage? I'd like to know the wattage.
Come on, wattage. Power output undistorted, 1 watt maximum, 1.9 watts. Okay. That's the output.
Power consumption, 35 watts. So we're going to run 120 volts into it.
35 watts. So maybe a little over a third of an amp it should be using. So
we should get up to 0.3, between 0.3 and 0.4, I would expect. So we're going to try.
So I want to watch the amperage, see if anything's shorting. That's the first thing. Second thing is,
I want to see if all of the tubes, if we get the tubes glowing, which we should because
we tested them all. But if there's a problem with the socket, they won't. And also,
if one of the sockets is messed up, none of them will glow because they're connected in
series, of course, right? All American 7. All American 5 plus 2. All American 5 plus that FM.
So I want to see if we can get the filament line lit. And then I would love, it would make my day,
if we got some kind of amplification out of it. If I could hear a buzzing
or that you know, you hear whenever it's cooking, that would be great. And then next time we can
work on actually getting it to tune in and cleaning up the cabinet and all of that.
We don't even have the antenna hooked up. So I've got the wires where they're not touching anything.
So none of them are touching each other. And we still got the power line just rigged up.
Okay. So we're going to do the same thing we did before. I've got the voltage at zero.
I'm going to turn it on and actually turn it way up. And then we're going to slowly
turn up the voltage and see what kind of amperage we get. Oh yeah. Oh yeah. She's starting to go up.
Okay. So we are at 30 volts and I've done this before. And when I get to 55 or 60 volts,
you can already hear amplification. Sometimes you'll even start getting channels, but I don't,
this one doesn't have the antenna hooked up. So I don't know if we can even possibly get channels.
I don't know. It's sitting down pretty low. I don't like the sounds of that, but we'll see.
So we're at about 90 volts. Let me go ahead to where we need to be. Okay. That's going to be
about 120. We're sitting at under a third of an amp. It's awful crackly. Might be silver mica disease.
Turn it back down a little bit. Okay. It's got a little hum in it with no signal
or with no volume, no application, but that doesn't really bother me. Okay. So let's change
the, let's move through the plate. I don't even know if we're on AM or FM.
Let's see if we can get it to change. So I don't know which is which. I guess I could just look at
the, it's so dirty. I can't tell. Let's say to the left will be FM, to the right will be,
no, we figured that out before, didn't we? That's not how it is. They both say that.
So I don't know which is which.
Did it die on us?
Might have died on us. I wonder if my, that's my hokey power line. Oh yeah. It's the power line.
Well, how do we know which one's AM and which one's FM? Okay. It does look like on the,
on the knob, it has a little thing that points towards the FM or the AM. But my whole point is
it says it on both sides because it's just showing you what meter to use. But it does look like if
you're down, you're at FM. If you're to the left, you're at FM. If you're to the right, you're at AM.
So I don't think we'll get FM. Let's put on AM. So that should be AM.
Let's see if it wants to give us anything. Now here, here in Charlotte, there is a
blow torch. There is a station four miles from here as the crow flies. That's a 50,000 watt
station WBT 1110 AM. You can feel it when you're brushing your teeth.
It also has harmonics basically. I don't know how that works,
but I think what's going on is we're getting near 1110 and you start catching it. If we get to 1110,
it'll like be loud as hell, but there's no antenna. So maybe that was it, but I'll bet that
was one of the harmonics. Maybe not. All right. So yeah, it sounds like good old 1110 came through
So let's move over to FM. Maybe FM gets a better signal without, you know, maybe you don't even
need an antenna. I don't know. We'll find out. I can get the volume knob back on. I think our
connection's crooked. Obviously my connection's not perfect here, folks. All right. So let's try
to switch over to FM and just see if we can get anything. I'm going to have to make the proper
I'm not so sure that that is silver mica. I think it might just be you're not getting any signal,
so it's tripping. Okay. So wasn't there something with the antenna on FM
where two of the wires connected together? And I don't have it connected together right now.
Yeah. So there is the FM antenna. And if you look, there are two wires that go to one of the
contacts that actually connect together. And they're not connected together. So there's one
real long line that comes over from the front. So I've got it. I know where it is. And it connects
to one of the lines that went to the antenna connections on the back. So it could be without
that voltage connected there, that just won't work at all. That FM will not work. So it could
be that you don't actually need the antenna hooked up to get any reception, local reception.
I don't know. I mean, I assume you need an antenna, but without those two lines together,
maybe it's impossible. So let me see if I can figure out which one's which,
and I'll tie the two together real quick and see if that changes our FM reception at all.
So I found the two wires. I have connected them together. We've got the voltage off.
Let's see if that changes our FM reception at all. Where are we? Turn up the juice. It's about 120,
122, something like that. I suppose y'all would like to see the juice, right?
You want to see the juice? You can see it a little bit. That's a glower there. Look at that one.
There's our little 12A05 doing its thing, and there's the 50C5. You know, those are powerful.
All right, let's see if we get anything now that we've got those two antenna wires together.
Nothing. Oh yeah, look at the slugs move. People were telling me that the slugs were moving out.
I just finally saw it. This is moving up and down. All right, so we got nothing on FM. It could just
be because I don't have an antenna, or we could still have a problem with the radio. But on AM,
we do seem to be getting some reception, but just barely, and it's not aligned yet, of course.
So I don't know, folks. I call that progress. What do you call it? Technically, it's a working radio.
It's only AM, and it's the faintest signal on the strongest channel, but technically,
it's working. But like I said, my toothbrush picks that up. So it's not super impressive,
but we need to align it. We need to do some more testing. We've got more stuff to do, so we'll do
that next time. So I hope you've enjoyed it. So we'll see you on the next one. Leave your comments
below. Let me know what you think so far. Tell me what I'm missing here. Tell me what I need to get
straightened out before the next video. And with that, I think I'll go ahead and throw it to the
theme song. We'll see y'all next time. Take it away. Ladies and gentlemen.
Dust-covered circuits, sitting on a desk. Been lost in time, 50 years of rest.
Reading schematics and drifting on pause. One more last, last week. Oh, poor new scars.
Tracing faded traces, vacuum tube blows. Get it back to working by the end of the show.
Bringing broken gadgets back to life. Turning silence into stories, one at a time.
We fixin' to fix some, easy as can be. Amateur repair time for you and me.
Little machine that carried history. Time to trace your back, bring your mystery through.
From welcome to singing, learn, preserve, repeat. Cables, needles, switches.
Tangled up, patient Google searches. Pass me the bars.
Dotted clock, it's ticking. Take every star. Brittle capacitors, rummaging old walls.
Tracing faded traces, vacuum tube blows. Get it back to working by the end of the show.
Bringing broken gadgets back to life. Turning silence into stories, one at a time.
We fixin' to fix some, easy as can be. Amateur repair time for you and me.
It's amateur repair time. It's amateur repair. It's amateur repair time.
