Like and Subscribe if you like what you see! Twitter @jaybates86 facebook.com/jayscustomcreations youtube.com/jayscustomcreations
Check out my other channels SolidWorks, AutoCAD, and SketchUp designs: www.youtube.com/JaysCADD Household and apartment maintenance: www.youtube.com/ApartmentMaintenance Project plans: https://jayscustomcreations.com/plans/
all right so these fit incredibly tight
as it is I just added a little dab of
tight Bond
three and uh we'll see how this
works probably going to break a couple
of these forcing them in there but oh
[Music]
well I'm down here doing this on the
ground on the floor because
it's a concrete floor underneath this
ceramic
tile
and I don't
have an incredibly stable workbench to
be pounding this down
[Music]
so
[Music]
all right that's done that's
uh well that's one of them all right so
the glue is all set up in these and uh
it turned out all right but what I want
to
do uh like I said I want to put a 30°
chamfer on all the edges and to do so
I'm just going to use my mitor slot
blade Tilt at 30 or my miter gauge
rather and
uh got a little bit of a problem because
I I put I cut all these with a stop
block but you know getting all the
grooves to line up there's a lot of room
for error and a lot of room for uh a
little bit of changes here and there so
if you can
see I'm exaggerating anyway it P this
one's pivoting on that middle section
so I got to figure out a way to make
these uh a nice uniform cut with every
single piece and uh as of right now now
I don't know if I can do that so I think
I'm just going to make a couple test
cuts and see if I can't just hold it in
place and see how that
goes okay my my M gauge uh didn't work
out like I like I hoped uh there's just
a little bit of wi wiggle in here and uh
I I just didn't like the way it looked
cuz the the first piece entering the
blade is never on both sides was the
same as the last piece so I'd have to
adjust it by hand to get it to work um
anyway I've got an old small
sled uh that I used to use and um I
think I'm just going to I haven't used
this thing in forever so I think I'm
just going to start cutting it off right
here and see how that
works
all right so my markings are no longer
relevant uh but now I have a uh zero
clearance 30° bevel on this particular
sled so uh I like I said I made this a
long time
ago and I made it for one particular job
it served purpose and I never used it
since so uh repurposing old
jigs but anyway now I'm going to run all
these through and see what we
get all right the way I cut my first
lower elevation Cuts is I just struck a
90° line here and I just I balled it and
made my cut because this is zero
clearance uh I can look down at the
piece and I can tell if I need to uh
slightly adjust one way or slightly
adjust more into the blade and uh my
objective was just to make one side look
like the other side I don't care if they
all look the same throughout the set or
whatever but you know this all going to
be fairly
similar uh to cut my higher elevation
pieces um no need to adjust the blade or
anything all I need to do really is take
the piece slightly more into the
blade so that my shoulder on the lower
elevations is the same as the shoulder
on the higher
elevations uh it's just sneaking up to
it it's all that there is to it and each
one's going to be different
so uh this should work out just
[Music]
fine so of the nine I had two that died
on me uh this
one split open like
so and this one had a little bit of a
chip out just a little bit of chip out
you see that
yeah just a little bit of chip
out so I don't know these two are going
to be decorative wall art for the
shop and like I said I've got some more
scrap cut offs that'll be good for
veneering
and I've got
seven that turned out pretty good so
kind of happy with this little
project um I'm going to touch them all
up with some small sandpaper
uh just to get rid of all the you know
the little uh tear out and small stuff
and after that I'm going to I guess I'm
going to soak them in some mineral oil
uh got them all nice and sanded and I
used my uh the sharpest chisel I had and
my little sanding pad to get all the
corners and this job has really turned
out this project has really turned out
to be a lot of work
so uh you know just the design I guess
of it just creates so much little little
stuff here and there but uh work never
hurt anybody sure does make your hands
sore though so uh time for some oil I
just to seal these up I'm using mineral
oil again uh I took an entire bottle and
dumped it in this baking pan and I've
got it set on these scraps so it's
leaning towards me just a little bit and
all I'm doing is just soaking the end
grain
first and then
uh submerging it in the
oil make sure the entire surface is
coated and then just stack them on the
next one uh they will continue to drain
and weave down and the oil will keep
coming to
me and I'll just keep
uh keep putting it on all right so this
is the last one uh I'm going to let
these soak uh the way they are I don't
know for a couple hours or
so and uh and then I'm just going to
complete the processing one more time
just to uh just to seal these up all
right so it's been a little while uh
couple
hours and I'm just going to soak them
again and let
them soak them again and just let them
sit for a little
while after that we going to wipe all
this mess off
so that'll be fun most of this stuff uh
because it was so soaked to begin with
absorbed all it can absorb uh but some
of these some of these have some dry
spots that I just want to hit again so
uh that's the only reason I'm doing this
twice so if you're wondering why I have
a stove in my shop um go back and watch
my shop tour video but
anyway this
is where I store all my oil projects
such as cutting boards and whatnot stor
in
there uh that way I don't get any dust
on them so but but you've never seen
that wood storage in a
stove but
anyway uh that's that's unplugged by the
way so there's no electricity to it uh
I've got my trivets sitting Above This
pan uh I I put these little
uh popular scants on there just to allow
the oil to drip down in there and
they've been dripping for I don't know
about 2 hours so it's been about four or
5 hours since my original first coat on
it so it's time to just wipe these off
and see what we get here they are all
completed uh each one is unique from the
next I just took a paper towel and wiped
them all down they're still kind of oily
but you know that'll dry U very pleased
with this again just just using some
scraps from The Trash to Treasure videos
so I like the I like the profile I like
the shape it all turned out
well each one has some flaws but you
know who
cares um
some of these some of these have some
nice looking grain to
them
and the oak of course predominant grain
so that look looks pretty
neat but anywh
who I think they turned out all
right so yeah Trash to Treasure this was
you know series of different things I've
taken apart using up some scrap um hope
you like it hope you've enjoyed if you
like what you see like And
subscribe and uh just to be honest with
you I've never heard of a trivet until I
saw um Lany from a simple design of
ellaa uh he made some trivets on a
router table not too long ago I'll put
the link in the descript in the
description but that's the first time I
heard the name trivet so you learn
something new every day YouTube's pretty
cool but yeah like I said if you like
what you see like And subscribe thanks
for watching and you guys have a great
day