Salvaging a blue love seat that was left for the dumpster. Giving new life to some old wood.
Like and Subscribe if you like what you see! facebook.com/jayscustomcreations youtube.com/jayscustomcreations Project plans: https://jayscustomcreations.com/plans/
Alright, I was coming over to the shop today and I found a loveseat next to the dumpster.
So, I guess we're going to get a cutting board or two out of this one again.
Normally, let me just say, normally I don't chop up everything that I find.
I'm maintenance at an apartment complex, so I see a lot of this stuff come and go.
In a college town, kids throw away all kinds of stuff.
So, if it's halfway decent, I'll take it over to the Salvation Army and let them sell it and all that good stuff.
But, if it's junk, like this one is, I've got some tears in the seats and there's some Kool-Aid stains all over it.
If it's junk like this, then I'm going to tear it apart and get all the hardwood out of it.
But, anyway, I've already gotten the bottom off.
Let's check inside.
And, of course, a spring destroyed coming out.
This thing, there's no saving this thing.
But, all the wood in here is oak, except for a couple of three-quarter plywood supports.
The vast majority of it, these wider boards, is all oak.
And the arms on this thing were flat-topped arms, so I haven't gotten into them yet, but I think they're a nice wide piece of oak.
The back supports, those are always wide pieces of oak, or wide hardwood pieces.
And then this piece where your thigh normally rests when it's upside down, that's normally a nice decent chunk of hardwood.
And, of course, the seat stretchers.
I'm going to tear into this and hopefully get some of this cut up and ready to go.
Find somebody who needs a cutting board.
But, more fun ahead.
I always find it best to remove as much of the fabric as you can before you start taking off the good wood.
The reason being is if you start just ripping off wood, you weaken the frame.
And then when you get down to one side or one corner when you want to take some pieces off, it is so hard to get them off because there's so much fabric tying everything together.
And the frame is weakened to where you don't have any rigidity to start yanking stuff off.
But I've gotten most of the fabric off.
I already took a couple pieces of wood off as they fell off, really. This thing was falling apart.
A couple of little goodies. A remote control, yeah.
Bet someone lost that a long time ago.
A pair of scissors. I've been looking for a pair for the shop, so Merry Christmas to me.
There's a lot of good hardwood in here.
I've got a three inch section all the way across here that has zero staples in it.
I'm going to be cutting off most of these staples with some junk blades and salvaging what I can, really.
Oh, also, another little goody.
The legs have some nice T-nuts just sitting in there, not secured hardly at all.
So I can pop them out and get a couple of free T-nuts. I have four of them.
Those aren't cheap, and they always come in handy.
I got as much of it off as I could.
There's still some pretty big pieces of oak over there, but it's too riddled with staples.
I've got a little bit of a mess, but I was able to salvage a lot of good.
Most of it is red oak, and I've got some white oak, and some more white oak.
A few, what looks like walnut strips.
I think it's walnut. I put a little bit of oil on one to figure out if it is.
Sometimes they chop up some beautiful wood.
Anyway, I don't know if I will be able to get a decent sized cutting board out of all this.
But, we'll try nonetheless.
All these staples that are in the face grain, or on the face of the boards, those really don't matter.
If you cut your board thickness this way, with the top being here and the bottom being here,
then that's going to be on the inside of the cutting board.
Some stuff like this really doesn't matter.
However, if you've got them on the sides, going straight down like this board.
Let's see.
Here's a couple where the next piece was stapled in like this.
If you cut this off, then you still have the holes, so that's not really good.
But, I'll be able to salvage a lot, so.
Still got a lot of nails to pull.
Staples to pull.
Well, here's what's left of the sofa.
I've got a scrap pile of destapled hardwoods.
All of these are going to go in the scrap bin for future jigs and small projects and stuff like that.
You know, nothing fancy.
Some junk, and what is going to be a cutting board.
And no specific orientation yet.
The final sizes are going to be right under 11.
It's probably going to be around 10 and a quarter once it's done planing and trimming.
About 10 and a quarter by...
I'm going to say it's going to end up around 19, maybe a little less.
I wasn't able to get a lot of good use out of this stuff, so right now it's at one and a quarter before it goes through the planer.
So, I'm hoping to stay above one inch.
You know, it's just a cutting board. It may warp a little bit, but hey.
Something out of nothing.
So, anyway, I've got my planer set up here on the bench.
And what I plan on doing is taking some of these boards, actually all of them.
And most of them have a rough face on the glue surface.
So, I'm just going to run them through the planer and smoothen up those faces.
You know, they're not 100% straight.
I don't have a jointer, and I don't want to put these through a planer sled.
But the amount of twist that these have is very minimal.
And glue and clamps will pull everything together.
So, I'm going to get this done and clamp it up tonight and call it a day.
So, just like last time, we've got a good side and we've got a bad side to all of these pieces.
And I'm just going through here to make sure that I'm putting the bad side down.
This is going to be another one of those directional cutting boards.
And this one, this particular one is going to my co-worker's mother.
She brings me some homemade jelly, so I will make her a homemade cutting board.
Now, like I said, some of these pieces do have a little bit of a twist to them.
But I'm really not worried about that.
It's not much to really cause any kind of harm.
And it's going to glue up just fine.
And if the cutting board doesn't last because of that, then, you know, throw it away.
That's where this stuff is going anyway.
But I'm just using a paintbrush to smear this glue.
Clamped up.
I've got some good, even glue squeezed out along all its seams, so I'm happy with that.
I'm going to set this over here to dry overnight.
And for this, a handful of sawdust.
And let that dry.