Turning a junk headboard into some decent salt and pepper shakers :)
Like and Subscribe if you like what you see! facebook.com/jayscustomcreations youtube.com/jayscustomcreations Project plans: https://jayscustomcreations.com/plans/
all right so this is part of my day job
um college town people come and go
people abandon people just don't really
care at all and the tenant in this
apartment just left so there's all kinds
of uh all kinds of
goodies that they abandoned and it's my
job to throw them away so uh most of
stuff like this big stuff table chairs
that'll go with Salvation Army and
somebody could use that but most of the
time you find junk like this this is
all uh veneered particle board this is
all let me see if I can't show
you how sturdy this thing
is so anyway these
legs are maple I believe they're Maple
they're nice hardwood but they they've
got this uh veneer part actually say
veneer MDF is what it looks like
uh it's got it mortiest into the pieces
so I can scrap some of this most of it's
junk so I will cut off probably from
here up and have a nice hardwood
something or
other uh same with this cut off as close
as I can up
here and as close as I can right here
and have something that may serve some
use down the road but what I'm going to
show
here I've got a nice Chunk from here to
here with
nothing uh nothing in the way so I'm
going to cut both of these out both
sides and I'm going to make some salt
and pepper
shakers so that's a nice solid chunk to
work with and I
may uh May throw in a lamination of a uh
contrasting wood in different spots to
signify salt and signify pepper but I
want to use this and the rest of this is
just destroyed it's junk and it's all
beat up and stained and nasty
so Trash to
Treasure in order for me to raise my
blade in between this little bit of
support I had to remove my had to remove
my ring knife so I'm going to make a few
couple or I'm going to make a few cuts
um with this setup and then put the ring
knife back in
[Music]
all right with the majority of this
trash cut off uh I'm going to use my
miter gauge to uh cut off what I can and
Salvage
[Music]
[Music]
[Music]
all right I've switched over to a uh
lesser quality blade uh just in case I
accidentally do hit one of these nails
that might be in the way uh I've done
some measuring and I I believe I've
allowed myself enough leeway to miss it
but I'm just trying to slice off as much
of this uh usable Maple as I can uh it's
unfortunate they use some metal
fasteners here else I would have cut off
a lot
more but uh that being said I should be
able to set Salvage a big chunk of this
Maple so let's see what
[Music]
happens so after all the chopping up of
the headboard I'm left with these
uh inch and a/4 by 3 by random lengths
uh blocks of some really nice
Maple um also these 3x3 by7 I've got two
of these
chunks and some miscellaneous uh
turnings uh
this looks like a lamp may be down the
road but I've got
some got some more parts to work with
and what I'm going to do first is I'm
going to take my 3-in blocks and I'm
just going to skin down the sides uh on
all four sides with the best blade that
I have uh just to get a little bit
better appearance of what we're working
with and I'm going to try and maximize
these to get the most out of them and uh
maybe make I don't know cut down here
and I'm to cut this way and then you got
four pieces glued up with some some
popler or something I'm I'm going to
make make some salt and pepper shakers
just not exactly sure how so we'll see
what
[Music]
[Music]
happens
[Music]
all right not only did I square up
square up all this Maple the the larger
chunks but I went ahead and took all the
smaller pieces and surfaced them three
sides uh surfaced them three sides on
the table
saw so that I'm left with some pretty
good
stock and what I'm going to do
here is I'm going to take this piece
and if I cut it in half this way I think
I can get the height for for two
possibly three
um all right what I did is I surfaced
all four sides of this maple on the
larger chunks and then I surfaced three
sides on the uh smaller
pieces uh they're all the same thickness
and they're all 2 and
7/8 uh this 2 and 78 in with various
lengths um I didn't surface the last
side because I can always no matter if
I'm using this side or this side of the
salt and pepper shaker I can always do
that last just to clean things up so
what I'm going to do now is I think I'm
going to start ripping this stuff
into into 3/4 in
wids and then we will start to go
through the hard hardwood scrap bin from
other salvaged materials and come
together or come up with some type of
laminated design that I can glue back
into a block uh and then we'll use a
forer bit to drill out the main cavity
drill out a little bit on bottom drill a
small hole in the bottom in the middle
of that cavity for a cork so you can
reload the uh salt and pepper shaker and
then on the top where the the the main
cavity is we'll we'll surface it with
another piece piece of hardwood and
drill some holes in the top for it to
flow out of um that's the plan so I'm
going to get some of this stuff cut up
into 3/4 in widths and we'll try and see
we'll try and see how how good uh this
comes out comes
[Music]
along
all right I've got a bunch of these cut
up that are 3/4 by inch and a/4 by
various
lengths and what I'm going to do is I'm
going to have this is the side of the
salt and pepper shaker I'm going to
space them out a little bit and put some
contrasting color in here for a
lamination uh remember this this green
piece of popler from one of my Trash to
Treasure videos that's going to be a
good contrast for this uh for this maple
so I'll have a cutting uh I'm sorry a
salt and pepper shaker on the outside
looking something like that now what I'm
going to have to do is laminate one side
laminate the other side glue them
together so it's going to have like a uh
looking down it'll be like a cross of
lamination maybe the inside will be
removed um but anyway this will all
start making sense once I start putting
it all together uh I need to know how
thick I want my piece to be
so I have a 1 and 38 inch forcer bit
that I'm going to use to remove most of
the
material and this is 3/4 inch wide this
is 3/4 in wide so that's inch and a half
and I want to be at 1 and 7/8 so I just
need to rip this down to 38 of an inch
to give me some spacing to go in between
uh that'll leave me with the material
cutout Plus a/4 in and 1/ qu inch on
either side it's going to be plenty for
what this is going to work or for what
this is doing so I'm going to get all
this cut up glued together and I'll show
what I've got so I went ahead and ripped
four of these strips of that popler uh
they're about a/2 in this way a little
more than a quarter this way and
whatever that is that really doesn't
matter uh what I'm going to do with
these is I'm going to laminate them in
between two strips of maple uh that you
notice they're not coming out all the
way the same width as these other pieces
but that's okay um and I'm going to glue
them flush with the prear varnished side
from the uh headboard and that way I can
Surface this all nice and smooth and all
three of these planes will be even I'm
going to come in a/4 inch and then it
doesn't really matter because my forer
bit is going to remove most of this
material anyway so really all I need is
a straight line and/ qu in in for my
Forester bit to have uh leeway all the
way around but anyway I'm going to do
this on one
side uh I'm going to do two of them so I
have the Sid to let them glue up
and then I'm going to trim this to the
final length and then I'm going to do
the same
thing this way so when it's all said and
done I don't know if I'll be able to
hold this when it's all said and
done it will look something like this as
far as the laminations go now the size
it's going to be a 1 and 7/8 in uh
square but
for yeah I'll just hold it like that
this is the lamination setup it's going
to be 1 7/8 in square when it's all said
and done and
uh um I have length here to cut this one
in half and I have a salt and then a
pepper and the top piece I'm going to
use I don't know maybe a piece of maple
for the salt and walnut for the pepper I
don't know something like that but this
is the route I'm going with with my
laminations