Alright, I'm back in the shop today.
I let it dry overnight.
And I'm going to clean up the table real quick.
Just push all this back into my dustbin.
And I'm using a paint scraper here to remove this.
It does a really good job.
As far as the bench goes,
this is a work bench.
I do work on it.
I don't care how it looks.
And just that quick.
Back to being good as new.
Let's do the same with this thing.
More clamps.
And we'll see what we got.
Like I said, a lot of glue squeeze out.
A black box needs original two black clamps.
But I don't care because
I'm going to clean it up anyway
before I run it through the planer.
So what I'm going to do here
is I'll just clamp down
if I can find another clamp.
And then I'll go
clamp down opposite corners
and start scraping.
Sometimes you've got to
move your clamps.
I don't have a bench vise
and I don't have a
bench dog system or whatever to hold this down.
So this works just as fine.
Spin it around to get a different angle on it.
Alright, from here
I've got all the large chunks off.
Now it's relatively smooth.
Obviously there's glue on here still.
What I do is I take my two planes
Both of these are $10 planes.
I'm not worried about screwing them up.
I've had to rework these a couple times.
But that's what they're here for
is to be used.
So I'm going to use them.
Another reason why I'm doing this is
once this is done I'm going to run it through my planer.
But I don't want any of this glue to
screw up the blades.
So I'm just going to go ahead and
clean it a little bit first.
I've got this set kind of aggressive
because this is typically what I use it for.
I've got a low board right here.
It's got a little dip in this piece of wood.
But anyway
I'm going to go ahead and get all this cleaned up and
flip it over and do the same thing on the other side.
A couple low spots but
the vast majority of the glue is removed.
So that's good enough for me.
I've also got a bucket right here.
A larger trash can.
For my dust chute on my table saw.
So it's convenient.
Just brush what you're working on right into it.
Alright I have a DeWalt 735 thickness planer that I'm going to use.
I had some profit a couple months ago from a decent job.
And I figured I'd splurge on something that may
open up the doors for me down the road.
I've got a little piece of melamine shelving material
with a stop block located here
and also here
to straddle the bed of the planer.
And that just increases the in-feed and out-feed just a little bit
without adding any type of fancy mechanisms.
That can be picked up and slid out of the way for normal use.
What it's sitting on is an old sink-based cabinet that I've salvaged.
Put some wheels on it and makes a great mobile table
in the shop.
Now the planer ejects chips
with a fan very efficiently.
And normally what I do is I set it basically where the cutting board is
and I point it in my direction
shooting against that wall.
And that's like a 15 foot, 15-16 feet in between the wall
and where it was at.
And I would get a pile about in that outline of the chips.
And none over here.
This thing shoots the chips into one direction.
I don't have any type of collection for it right now.
I'd love to make some down the road,
but for right now I'm going to use it as is.
So what I did is I positioned it
in front of my iBuildit.ca miter saw stand.
Miter saw station.
And it's got pretty efficient dust collection for that saw
without any mortar or whatnot.
Just a bin basically.
And if this thing picks up, I don't know,
30% of what it's going to throw,
then I'll be happy with it.
I'm just aiming it right now at the back of that.
Not ideal, but better than nothing.
I'm going to run this cutting board through
and we'll see what happens.
Safety glasses, hearing protection.
All right.
That thing is just simply blowing too much air
and that is too close.
So what I'm going to do is spin this around
and this is on wheels too.
So basically I'm going to set it up
kind of how I had it.
This direction, a little bit longer distance shooting that way.
This isn't ideal and I'm just playing around here
so hopefully I can get some amount of this dust picked up.
It's probably just a waste of time, but oh well.
All right.
So there's the cutting board.
Looks pretty good.
This, like I said, was a waste of time.
Too much pressure.
Everything that went in just blew out.
And I've got a little mess to clean up.
But hey, I figured why not?
Let's give it a little bit of a try.
I got some collection in here.
But yeah, just a waste of time there.
I've seen a lot of dust collection systems with this.
You don't even really need a motor.
The thing blows out so strong.
I'm definitely going to do one.
It's just a matter of time getting around to do it.
Anywho, that was fun.
Here's the board.
I'm going to start cutting it up.