We have emptied the shipping container and moved on from that phase of this crazy adventure. During the summer months, I checked the machine surfaces for signs of rust. However, I stopped checking regularly since we had no issues for the first 6-7 months. Then, the cold weather came in, and mistake #1 was made. I quit checking for rust right when the condensation started showing its ugly face. I estimate that the last month of storage in the shipping container was full of condensation nights or mornings. Luckily, the container was not level. The container sloped to the right and to the rear, so only one of my machines really got the worst of it. My poor planer table looks horrible. Lots of rust and definitely a few hours of work are on the to-do list to get it back to working condition. Luckily, the planer was the only tool that got it bad. Unintentionally, I haven't shown it on camera yet. You'll see it when I get the time to clean it up. Also, we didn't get any significant mold issues on our personal belongings and only lost one wall decor print.
Mistake #2 was a big one. More accurately, mistake #2 was a 980lb mistake. I also mistakenly referred to its weight as 1,100lb. Anyway, I had a mental lapse in judgment and thought it would be OK to pull the jointer pallet forward by simply looping a strap around the base of the jointer. Oh, the instant regret. I should have looped the strap inside the pallet like we have been doing, and instead, I pulled the jointer over onto its side. Luckily, the fall wasn't from a considerable distance, and the pallet in front of it took up a lot of energy on the way down. I think so, anyway. No visual damage at all to the jointer and my dust collection barrel just got a minor 3-4" dent. Easily fixable. Regarding the jointer, I think it was just knocked out of calibration. Annoying and frustrating, for sure, but it could have been way worse. Nobody was hurt, and metal was scratched. A few years ago, I would have blown up with frustration and anger. This whole new land adventure has prepared me to better accept, adapt, and move when plans go astray. It fell, oh well, time to move on. #homestead#mississippi#tractor#badboytractor#forest
** Brand Partners ** ** Woodland Mills ** @woodlandmills #DiscoverTheWoodland#Woodlandmills#WoodlandMillsAmbassador - WC68 Woodchipper - WG24 stump grinder ** Lane Shark ** - Lane Shark LS3 ** Bad Boy Tractors ** - 5' box blade - 6' grader blade
Mint Mobile: Regularly $30/month for unlimited talk, text, and data. 50% off right now, so $15/month for unlimited talk, text, and data. I'm using this at our new property. Affiliate link: https://trymintmobile.com/bpo3
BRUNT Workwear: I have two recommendations from BRUNT, both are summer time work clothes that I've been wearing year-round. The Costello Pant are light weight and durable. The McKenna Tech Long Sleeve Sun Shirt saved me from being lifted away by mosquitos this past summer. Now that winter has set in, I'm finding it to be my go-to extra layer. When a coat is too hot but a regular shirt is not enough, slap this long sleeve on and get to work. Affiliate link: https://www.pjtra.com/t/2-529833-342731-289744
xTool Laser: We have the P2, F1, and F1 Ultra. All three are great machines. We typically use the F1 for fast engraving on smaller stuff, F1 Ultra for similar tasks or when we want to engrave on metal (fiber laser), and the P2 when we want to cut or engrave larger wood or acrylics. Affiliate link: https://www.xtool.com/?ref=x57e1_kqAgBT4A
Today is big moving day number two,
and we're gonna try and get all the stuff
out of the Connex, the majority of our stuff anyway,
all of our palletized machines
and the rest of our belongings.
I'd love to empty it today if at all possible.
It's pretty darn cold outside.
It's in the low 30s right now,
just the ground's still warm enough
to where there's no ice in the puddles and the sun's out,
but it's cold today.
Yesterday was this cold, but brutally windy,
so thankfully we don't have the wind.
It's gonna be a lot of back and forth,
so I'm gonna try the GoPro on the head strategy
for the majority of this,
but let me spin you around,
and I'll show you the thought process here at the shop.
The ground is stable enough to drive on it, no problems.
You can see the color difference right here.
That stuff is starting to dry out really good.
This stuff is a little bit more wet.
The deeper stuff, you know, where I drove yesterday.
So we're dry enough to get in there,
but I don't wanna keep tearing this up a lot.
Like the initial plan was to put the trailer right there,
and then just use the tractor to pick and drop,
and pick and drop, but that little back and forth turn,
back and forth, back and forth up there
would just create ruts.
I know this from when the shop was built.
So the strategy today, I think,
is to just drive the truck and trailer right there,
and then I can use the tractor to pick and drop off,
and come back, and pick, and drop off.
The only crappy thing about this process
is the thing that's gonna slow us down the most
is we have one pallet jack,
and I gotta have the pallet jack inside the shop
to move the stuff around when I drop it.
I may have to have the pallet jack on the trailer
to move the pallets in the back to the front
where I can get it.
I'm sorry, from the front to the back
where I can pick them up,
and I have to use the pallet jack inside the conics
to move the pallets inside the conics to the edge
where I can pick it up.
So it's gonna be a lot of moving a pallet jack.
That's gonna be the biggest annoyance from today.
I think so, anyway.
That's my prediction.
I really need to get that jack fixed.
You know what?
I think it might be beneficial to take this pallet with us.
That way, if we find more stuff to put on it,
it'd be easier to move a pallet than a bunch of small stuff.
So let's do that.
A few years ago, before we started camping,
we started hiking a lot with the family,
and our daughter was like three at the time,
something like that, and she wanted a walking stick.
So I made her this walking stick
that was taller than she was,
and it's just a little strip of walnut from my shop,
just a little something on the scrap shelf,
and I engraved her name on it with the CNC machine,
and it was hers, so she wanted to paint it,
and she loved this color, and she painted it,
and she's kept this one particular stick,
her walking stick she's kept for years,
and I think that is sweet.
That's awesome.
She'll find it.
I did find a goody in the Konex the other day
when we were in there,
my magnet roller, roll-around magnet thing from Harbor Freight.
I've had one of these for years.
I wish I would've had it
when I picked up all them screws the other day,
but now I've got it.
Let's go.
But my estimation is I can get four pallets
on there at a time,
and some of the small stuff we can cram around the sides,
but I'm not too, too worried about the small stuff.
We're having a relative help us with his tractor here,
so I want to get all of the tractor work done.
Immediately, and then we can come back tonight or tomorrow
and finish up all the small stuff,
but I'm thinking it'll take five loads
with this particular trailer.
The good thing is we are six to eight minutes north of here,
so the commute time is gonna be
total of 20 minutes-ish there and back commute time,
so 20 minutes per trip
versus the last time when we loaded this up.
It was an hour and a half, hour and 45 minutes,
depending on traffic, to get here,
and then hour and a half, 45 to go back,
so three to three and a half hours versus 20 minutes.
Hopefully, we can get all this done today.
Go down another inch or so.
Let it, there you go.
Let it drag.
Your forks were a little high.
There you go.
You're pushing it.
You're good all the way.
Six inches, three inches more.
You're gonna touch the next pallet, but bump it forward.
You're good.
Keep coming.
It's not gonna move from there.
That should be fine, though.
Right there should be fine.
Huh?
No, this isn't heavy,
but we gotta get the other tractor anyway,
other trailer anyway.
He said he's gonna put the green trailer on his truck
and go with us.
Nothing.
Because when did it get in here?
15 minutes ago or three days ago?
And how long has it been fasting?
How much food does it require?
I don't know.
Well, I don't know either.
I don't know either.
You wanna take this to the truck?
I'm trying to give it to you.
Is it heavy?
I mean, it's not light, but it's lighter than this.
Or do you want the thing with more grabs?
I don't mind.
It's not too heavy.
That can't get wet, it can't get beat up,
so that goes in the backseat of the truck.
It's in the backseat of your truck.
This push, push this corner.
One, two, three, push.
I'm gonna ride it.
Yeah, same thing, I'm gonna slide off.
Right, the whole bucket down an inch right here.
You're good.
You should be able to snag it from there.
I'm gonna chalk your wheel tires,
or your tires rather,
so we can push this pallet forward with the next crate.
He said you could put some stuff
in the backseat if you want to.
Thank you.
Fork's down.
Bucket up, fork's down just a little.
Go a little bucket up, there you go.
Now you should be able to push straight ahead.
I don't think you, hold on.
Now you're good.
Just go ahead and push, you're good.
You're pushing it great.
Now we go about another foot.
Your tire's gonna hit first, okay.
You can go another foot and a half.
We can still put that next crate on the back
and then push it all the way forward, I think.
Whole bucket down a good three inches.
Right about there.
That looks pretty good.
Dog, go to your left.
Left a little more, quite a bit to your left.
There you go, now you're inside, now you're straightening out.
You should be able to pick it up from here.
Just keep going down, there you go.
And you got it.
All right, bucket down by eight inches to a foot,
right about there.
And then come forward, whole bucket down.
And you're touching the trailer, there you go.
Now you can push forward.
Yep, yep, yep, there we go.
And six inches more, six inch more.
That should be good up here.
That's good for this load, yeah, it is, good.
My jacket was in the truck in the sun,
so the inside is all nice and toasty.
It is.
Yeah, that's fine.
We'll figure it out later, anywhere you wanna put them.
Can you bump the trailer?
Or, huh?
Hold on, we should be able to yank this one just like this.
Oh, that's that goofy one.
It's that goofy trailer, or pallet, rather.
No, no, release the pressure, put the jack down.
And then push it all the way forward.
All right, well, back up three inches then.
Your front rollers are on top of the jack.
Try that, right there.
You got it.
Let's use this to get those.
All right, so this flooring is slick.
Should be fine.
Do we have a dolly here?
I don't think we can move it with this.
This isn't a pallet.
Probably just right here, out of the way right now,
until we get an actual dolly to move it around.
It's fine.
Well, let's put it the right side up,
so it doesn't keep falling apart.
Nothing fell apart on it, they just came undone.
We lost the clip right here for this.
It's all right, it's good.
Good.
All right, so we're gonna put it right here.
We'll mess with it later.
Yeah, it is.
You can put the pallets this way too, if you need to.
I think I'm gonna try this one different.
I'm gonna go, let's go 90 degrees.
Let's spin it, I'll put the front this way.
And then I'm gonna put it in there like a V.
All right, now, let's put the front towards you some more,
beyond the fork.
And as I lift it up, it'll cradle inside here.
You push it back when I lift it up.
Well, that's gonna damage that.
All right, I'll put it back on this pallet,
or back on this fork, and I'll just go slow.
There we go.
Let's see.
Here, I'll take this out over there.
We might be able to just pull the bottom of the jointer.
We can get down to the, yeah, just put it right.
Yeah, it's tied to the pallet.
It's too damn heavy to tip over.
Oh, I need a bunch.
Let me get my side, and then I'll pull forward.
Or, yeah, this one's super heavy.
I might not be able to.
You got it?
No!
I did not think that would happen.
I did not think that would happen at all, for sure.
Well, lesson learned.
I'm gonna get this front pallet out,
and then we'll lift it up.
If anything, it's just massively out of calibration.
It's all cast iron, so it can't be damaged.
It's just out of calibration.
Yeah, it's 1,100 pounds.
This tractor can lift 2,200 pounds.
Yeah, we'll strap it and lift it.
I just 100% did not think that was a possibility.
I was over-psyched on my part.
We're all right, we're all right.
The weight is on the trailer over here.
You know what?
I'm gonna pull in over here,
and we'll try and lift it, straighten it back up
before we get this pallet out,
because it's on top of this pallet.
I want you to reverse time and say,
Jay, that is a bad decision.
Wrong gear.
Push, pull the strap over the top of that thing,
and I'll just take it in there like this.
Move the strap to the other side of that power pendant.
Can you go to that side?
Do we have enough slack?
There you go.
All right, if I can lift it up over the side,
I'm just gonna take it in there just like this
and set it down.
Is it both of them under there?
Yeah, let's do that.
I'm gonna redo this side now that we have it up.
No, I mean, it is what it is.
I'm not too super, it's not that big of a deal.
It sucks that I did it.
Poor judgment, but that's okay.
All right.
It's gonna,
no, no, it won't swing less if I lower it.
It'll swing further.
I just don't want it to be so much that it throws me down.
Put this down.
I'm not gonna put all the weight on it just yet.
I wanna shift the pallet
so we can still move it with the pallet jack.
You can still haul that in there.
That's good right there.
Yeah, this is the most difficult tool
out of the one we dropped, I dropped.
Everything else is easier.
Jointer.
So this is what's responsible
for making wood absolutely perfectly flat.
This is the most stressful, difficult one.
So we're done with the danger.
We need to get them as far, as far in as possible.
And then we're gonna have to move stuff around tonight
while we're in here.
Hello.
That's a wonderful echoey sound.
The Connex, the shipping container, it's empty.
It has served its purpose.
Load number seven.
There's still one load sitting
on the second trailer ready to go,
but it's just a few things, like four things.
This is the last of the large volume of stuff.
All of this is loaded with the dolly.
Most of it's not too bad, but I tell you what,
that bandsaw on the back, the Laguna 18BX,
it's got a mobile base, but the wheels on it are so small
that I can't get over this lip.
Loading the big bandsaw with this,
oh, that's a leg day exercise if I've ever had one.
Holy smokes.
But I got it up there.
The smaller bandsaw, the Grizzly,
it's not too bad at all.
There's a planer on the other side of that.
That's not too bad at all.
Just that bandsaw, holy smokes, that's a tough one.
Last load is, well, it's unloaded,
but we are, let's just say we're not organized.
Just a little bit not organized,
you know what I'm saying?
So I have to work on some stuff.
As far as the machine surfaces go,
router table, good.
Table saw, there's the table saw fence.
The table saw itself is behind this.
Table saw, good.
What else is over here?
The ones that didn't get it,
well, the old bandsaw, the 14-inch bandsaw,
it got a little bit on one of the corners,
but it was already bad to begin with,
not the end of the world.
My planer, oh, I almost cried.
That was in the back right corner of the Connex,
and we had a little bit of a lean to the right,
a little bit of a lean to the back.
Condensation, once the weather dropped in the wintertime,
that got the worst of it.
Very disappointed in myself
for not checking that as frequently as I did
in the summertime.
We didn't have any issues at all.
So I was like, yeah, the Connex is good to go.
Didn't think about the temperature dropping so much,
and the humidity just, well, it condensed.
That sucks.
The HS950, I believe is what it is,
the horizontal sander I have,
it is, it's a little bit rusty, not too, too, too bad.
Where's the other big thing?
Oh, the other planer, I'm sorry, planer,
the other bandsaw, the Resaw bandsaw,
you see a little bit right there,
which has kind of sort of always been there,
but the stuff on the backside wasn't there,
so that kind of sucks.
But all in all, not too bad.
Oh, did you guys see the jointer fall over?
What a dumb, dumb moment.
I had to elapse some judgments.
Our Jamie's uncle was helping us,
and we were gonna pull around the pallet
to pull the pallet back.
We were looping one of these straps around the pallet
to use the tractor to pull the pallet
to where the tractor forks could reach it.
And I went on top of the pallet,
but hanging on the backside of the jointer
right at the base of it.
So we're not really putting a lot of top force over.
It's like, oh, it'll be fine.
It wasn't fine.
Stupid lapse of judgment by myself.
It fell over, knocked into the barrel of the dust collector,
which is on the other side of that pallet over there,
knocked it in just a little bit.
I don't think it damaged the jointer at all.
I just think it knocked it out of calibration.
So that was the only stressful part.
Everything's in here.
Now comes the stressful part, moving everything around.
So again, I don't know what I have said
and what I haven't said on camera
because this video is several days in the making.
And our initial plan when we had access to floor space
was to go ahead and start setting up over there
with the smaller shelves and the laser station and whatnot.
And yeah, that's not gonna happen.
That's not gonna stay there.
We're gonna have to pull all this stuff back.
I'm gonna have to buy some actual pallet racking
so we can go vertical with our storage.
We have the vertical space.
We've got to go vertical, right?
So we'll go vertical with our storage spacing right here
with pallet racking.
I want to get a forklift to help me move all this stuff.
That would be so much more convenient for us.
And then once the camper is out of here,
from this I-beam to the door,
this is a 20 foot span,
so I don't know what that distance is.
I want to put some more pallet racking right there
and then potentially,
depending on which way the apartment loft ends up being
because I'm contemplating many decisions there,
I may put another pallet rack this way.
That way there's no excuses.
Keep the floor clean and go vertical with storage.
We've got the vertical space.
We've got to start using it.
But that start will be in the next few days.
It's currently two days before Christmas.
This whole stretch between Thanksgiving and Christmas
has just been crazy for me.
And we're going to piddle around with this,
but come January 1st,
I'm taking a couple of days off until I get stir crazy
and then have to start up once again.
But I am mentally drained right now.
That's for sure.
Got to go to return the trailer,
get some food.
You guys take care and I'll check in tomorrow.