Powering Up This 1930's Majestic Radio After All These Years...

Amateur Repair Time
257 followers
898 Video Views·Jun 22, 2025
If you remember the first video, the cord was so old and damaged there's no way this has had power ran through it in at least 30 years.
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to
Amateur Repair Time. Now, if you
couldn't tell by our last few videos
that we uploaded here on the channel,
those were videos from an old project
that I've had sitting around for about a
year, maybe a little longer even. Um,
that is this majestic Griggsby Grunbo
Grunow Gri Griggs Griggsby Grunow
uh majestic radio and I've had this
thing sitting around for a while. We
worked through it and did a lot of work
on it and I uploaded those videos to our
other channel a while back. Uh, but I
never finished the project and I hate
doing that. I've got a few things that
I've uh done that on through the years
and I I hate not being able to upload a
finished video instead of just u uh
unfinished project videos. So, I
like filming everything in advance and
then releasing it all at once if it's a
multi-part
series. Um which is why I re-uploaded
all of those. So, because I wanted to do
them in order um because I intend on
repairing this finally finishing it.
It's pretty close actually. And um if
you have seen those videos and you're
seeing this one now, then it must mean
that we actually finally finished
it. So, if you didn't see those videos,
basically, whenever I got this thing, I
bought it at an auction. I couldn't
resist because it was a wounded puppy.
One of the the the uh stretchers down
there on the bottom was broken. Was
actually
missing that one. You can tell it's
slightly different color. I think if I
put some clear on that, some like some
um uh Verithane on that, it will blend
in better. But um so we did one video
where we repaired the cabinet, cut a new
stretcher, put that thing back together,
and uh it's nice and solid, and that
that got the cabinet where it needed to
be. Then we did a second video where we
worked through this thing a little bit
and it
just had some rotten wires in it that we
replaced and it was just kind of
complex. There's a lot of stuff going
on. Um and then we did another video
where we had to replace some of the
capacitors. There were
um metal can capacitors like this one
uh mounted to the side here. and they
had done some hack job stuff where they
put some stuff in parallel to it and all
this. So, we removed all of that and put
in new capacitors and went through all
kinds of that didn't look good. That
looks like it's coming loose. Went
through all kinds of trouble to make
sure that the uh uh the stuff uh went to
where it was supposed to go and checked
it all out. So, I think we've got the
capacitors right except for that ground.
Looks like it's not right. Um, so we
need to mess with that obviously and we
need to uh check the resistors. We need
to check the
tubes. Um, and then we need to bring it
up slow and see if the thing works. I
think it will. It's a very
wellbuilt chassis. Um, just really nice.
So, uh, I think the first thing I'll do
is repair that,
um, solder joint there on the ground.
And then, uh, I'll get the schematics
out. I wonder if this is then right
here. I think I see them. I had them
right here the whole time. So, all those
other videos you
watched, the schematics were never far
away.
Um, so we're going to go through there
is
actually
a like a physical schematic where it
kind of shows you I guess that's what
you would call it where it kind of shows
you the wiring, how everything wires up,
but only on this side. So the the
previous video was us working through
trying to figure out what the crap was
going on on this side, but we got it.
Um, so this shows us the resistors, how
everything's supposed to be routed.
There's We haven't done the filter caps
yet, which are over here. Um, they're
actually underneath this. So, the wiring
comes up to this um uh these terminals.
So, what I'm going to do is I'm going to
take the wire from the capacitor loose
and um tie it off, tuck it underneath so
it's no longer connected, but uh it'll
still be mounted. There are these huge
metal cans on this. This is a very early
radio, so it it uh it's just way
overdesigned. Um I'm going to leave the
wires just in case somebody wants to go
back or stuff the cans or whatever in
the future. I'm not going to do that. I
don't care anything about that. Um and
then I'm just going to simply mount the
capacitors, the filter capacitors to
these terminal strips. And I think that
will work just fine. Some people said
that you can't do that. It'll introduce
noise. I don't think it'll be a problem,
but we'll see.
What do I know? Um, so we got to do
that. We got to check the resistors. We
got to check the tubes. We got to fix
the ground and check that one. And uh,
we'll go from
there. All right, I got that tacked on
there. Much better. These things, you've
got to heat that up really good to get
it good enough that the solder is going
to stick. So, I have to use this thing.
This is like a very high
wattage iron. I got this at a
um at an
auction. American
Beauty. What's it
say? American Electrical Heater
Company. It's a 100 watt
iron. Detroit. They still make
these. So, get you one. All right. So,
that has got that on there good. It's
not going to pop loose now. Should I
temp
fate? Oh, it's on there real good. It
ain't going nowhere. And that one, too.
But I don't want to keep messing with
them. I mean, you eventually you can rip
anything off, but I feel confident that
that's fine. All right. So, next thing
I'm going to do is I'm going to follow
the schematics and check out the
resistors so that I can go ahead and
order them if I need to order any of
them.
Um, uh, so we'll just see if they're if
they're close to spec. I'm gonna give it
like
20%. These are from the
1920s. You know, this is an old radio,
so I'm going give it like 20%. It's 100
years old. If it's within 20%, that's
probably as good as it was back then.
Uh, we'll roll with it. If not, I'll
order it. But the the main problem I
have is that like if that resistor isn't
any good, I'm not going to get anything
that nice. The the new stuff's junk
compared to
that. But, you know, we got to be
somewhere near tolerance, I guess. So,
we'll just measure them and see what we
got and we'll write it down and then
we'll
decide. Okay. So, I've been going
through testing everything. Um, and I
think we're pretty good.
It was a little confusing. Like I said,
this is a schematic of that. It's upside
down, though, but it actually is drawn
almost identical to how that is. So,
it's it's like a an actual physical
schematic. So, it shows you where
everything
is. We just happen to have the radio
sitting upside
down. So, you can go through and test
some of them that way. So, for instance,
this is supposed to be 4,875 ohms. I've
got 4,900. This is supposed to be 5230.
I've got 6110. That's a
little that's a you know that that is
almost 20% like I mentioned. Um but I'll
show you here in a minute. Uh this one
was supposed to be 3340. It's 3450. Very
close. 7900. It's
7200. Little low.
Um, but it connects to the volume
control which is supposed to be 1260 but
it's 1 point it's
1500 which kind of makes up for that a
little bit. Um, so anyway it just goes
on and on. There's a couple resistors
mounted on the bottom of the
thing that are actually right here.
They're are big and they are they're
like big coils of wire basically. very
they're kind of like this very
high overdesign stuff cuz it's all early
stuff. It was back whenever they
were, you know, first using some of this
stuff. And then there's one in
here. That one's not on the schematics.
That's for the
antenna. That's just where the antenna
connects. So that's this wire. And so
for instead of just being connected
directly to ground, it's connected
through a 52 ohm resistor. Must be some
reason. Um local distance switch open
for distance, closed for local.
Interesting. So basically, if you close
that, you would be
connecting this switch to ground. But
they have set it up where you were
connecting it to ground through a 52 ohm
resistor.
Um, and a lot of
these coils
here I wasn't able to check. I was
hoping to get values of all of them. I
check I was able to check one. I got 8.9
ohms across it, but I don't even know
which one it is. Um, we kind of went
through this on the previous video, but
these things are it's just an incredible
design. They have this big can on them
and then there's a big old freaking coil
in there. And they all look perfect
because they've been covered by that can
for a hundred
years. Um
um so you know I assume they're fine,
but the some of them have wiring coming
out. So, a couple of the wires I was
able to to check, but those the way
those things are
wound, there's
one winding that's, you know, connected
through the audio signal or whatever,
and then it it couples with this other
winding that connects to ground. And so,
you can't really test all that, you
know, it's kind of like the IF
transformers on the on the uh the more
modern
stuff.
Um, so but going through this is what I
ended up with. So going by this, I got
the numbers that I
got and I was able to write them in
here.
So one was 154. It was 155. It's almost
perfect. The volume control was 1260,
but it's measuring 1.5. Uh, but one end
only connects to this. This is a little
high. This is low. So, you know,
hopefully that works out just fine.
Um, this one 3340 is 3450. This one 5230
it's 6110. So it's almost 20% off. Uh,
we're going to roll with it though. This
one 4875 it was 4,900. And then I ran
into an issue where how do I get the
other three values? Because they're not
here. They're in a weird spot. They're
actually buried. They're potted in one
of the cans up on the top. So, one of
the cans is right here on the on the
top. I don't know if I've showed you
that in this video
yet. Look at these. It's It almost looks
military just because it's so old. Look
at
these. So,
this has resistors in it and this one
has caps in
it. It's just how they designed it.
And
so it shows the wiring on this
schematic. So like uh that resistor one
of like this line right here I know from
the other schematic runs into a
resistor and that's it down in
there. So these are these are resistors
and these are capacitors. So I was
trying to figure out how in the world
could I check those things and then I
figured it out.
I have this line right
here. It's a green
wire and we know that because they call
it
out. So there is a line that connects to
this resistor and it connects to the C
capacitor. So we've got A, B, and C,
which are filter
capacitors. And it actually mentions
what they are. Well, it does down here.
They're all two microfarad
capacitors A, B, and C. It would be
slightly different if it was uh if the
cycle was
different. And then it it shows them on
this physical
schematic. This is
that that can I was just showing
you. And so it is showing you that there
is a green wire for one of the caps
that's right here. And it connects to
that resistor. So that resistor, that
connection is right
there. And then it's showing you that
there is a blue wire coming out of the
capacitor one that connects to this lug.
That
lug is right there.
And then it's showing you that there is
a red wire coming out of here that
connects to that lug. So that lug is
right
there. So really I we have all of our
connections here. So if I if I measure
from
here to
[Music]
um
here we are measuring
from
here to
here. So we're meas we're effectively
measuring across that resistor inside
the can. And it it checks out cuz it's
1,550 and it measures 1544. So dead on
the money. And then if we measure the
other two, we're measuring from here to
here. We get 181 ohms. And then the
hardest one was this last one. So, but
we know where this
is. And then we know that this is one of
the
uh the uh filament lines on the G80
socket. So the G80 socket is here. These
are the filament
lines. So by measuring from
here to
here, we get our last measurement. And
they all line up. So it makes sense.
190. Um or does that say 180? Actually,
I think that says
180. So 180 and we got 181. 190 and we
got 186. So we're all It's pretty close.
There's a little bit going on. There's
not much I can do about it anyway
because it's inside the uh the can,
right? I guess that one
isn't this one, but we're going to roll
with it. Okay. So, then the transformer,
I was able to check
um the secondary on the transformer. I
couldn't check this. We're going to have
to eyeball that a little bit whenever we
get ready to do it. I could check these
three, but I couldn't find that lug. I
got to whenever we go to put on the new
power cord, we'll figure that out. I
thought it would just be right there,
but it is
not.
Um, yeah. So, I don't know. We'll that I
think that might actually be the
fuse. We'll figure it out. Um, so I I
checked the secondaries. So, we got 354
ohms on this winding going into the G80
socket. And then we've got these three
different
windings that are all
um filaments. So, this is a filament
winding. It's 0.2 ohms almost a dead
short, but I think that that's I think
that that's how they do that. Um, I have
on my pinball machines. Usually I don't
have to check the actual transformer.
So, I'm not sure what it would measure
on a pinball machine, but we've got 0.2
ohms on this, which is the uh winding
for the the um G80. And then it runs it
starts, you know, running the B+. And
then we've got 0.1 on
this, which is the filament winding for
um pretty much everything including the
pilot lamp. So the pilot lamp 3.2 volts
and then it's also running the filaments
for all of the
tubes with the exception of the output
tube. The output tube gets its own
winding and these are really low. It's
like 0.1 ohm.1 ohm. Only reason I think
that we're fine um and the tubes aren't
installed. Well, actually some of them
are. That would explain it actually. Um
the the only reason that I'm not
concerned is because I don't really
believe that three different ones would
short. So they must just they measure
really low. Um it it must
be h I'm thinking through it. I think
your problem would probably usually be
that the winding goes open and that you
lose the winding instead of it being
shorted like that. And it's just hard
for me to believe that three separate
ones shorted. So, it's it's probably
that's just how it needs to be to create
um those filament voltages. So, all that
to
say, I think we're good.
Um, we need to do the filter caps and we
need to check the tubes. So, these these
are the only caps I haven't replaced, I
believe, other than
um these inside this choke.
So, there's a couple caps here, and
there there's a onemeg resistor and a
35 meg uh 35
K
resistor. That's those two
there.
Um, so those two cans, I believe, are
these and the choke.
I think we got all the other capacitors.
Well, maybe
not. Those are going to be up on the
top. Basically, this this big old tuning
capacitor up on the top, there's a big
can there that's inside of that. So,
[Music]
um I wonder if those are film or what
those are. H I hate to take that whole
thing
apart, but we might. Maybe we'll bring
it up slow and see these. You know,
these are all across like audio
stages. So, if that
shorts, is it the end of the world? Is
it going to burn something up? I'm not
so sure.
So maybe we try it and just see what's
going on. But yeah, that's our last one
is these little
things. Oh, you know what? Don't we know
that? No, we don't know. I was about to
say, don't we know that those are film
because of their size? They're not small
enough that we know that they're ceramic
or film or whatever. We don't know
anything.
Okay. So, uh, next up, we're going to do
our filter our filter caps. And like I
said, the way I'm going to do it is I'm
going to find the lines coming out of
the bottom, which
are green, blue, and red. There's just
one wire coming out of
each. And we've got our ground. Right
here is this black. So, ground is
connected
here. One of the filters is here. So
from here to here is a filter
cap. One of the filters is here. So from
here to here is a filter
cap. And one of them is here. So from
here to here is a filter
cap. So I think that's all completely
doable.
that one there just for physical
reasons. I
might try to mount to something easier
if there's if there's a ground right
there that I can grab. So, that's my
plan. I'm just going to cut those three
wires loose, take them loose from their
junctions, uh tape them up, and roll
them up underneath the thing so that
they're still there if somebody wants to
try to restore that can at some point.
And we're just simply going to mount
electrolytic caps directly to these
lugs. Easy peasy. Okay, so next up we're
just going to clean it up a little bit.
Um, this thing is very heavy as you can
imagine. If you didn't see the first
video where we repaired the stretcher on
the bottom, the weight just basically
did it. This
this if I was just
guesstimating 60 lbs, something like
that, maybe even more. I mean, it's
freaking heavy and you can tell just by
looking at it, obviously. So,
um I think I don't well I don't know
which is which, but you know, you've got
capacitors and resistors and stuff in
these big um boxes, so we're not going
to mess with them at all. But then
you've got this little piece. We looked
at this in a previous video where there
are four tubes under
here. So, I think what I'll do is we
will clean all of this. just get it
cleaned
up and we'll test these tubes. I also
want to get if I can inside this to look
at what the tuning capacitor looks like
and um see if we can find those little
caps that apparently are in there
somewhere and just see what they look
like. Um and I'm just going to wipe it
down to get all of the uh the dust
bunnies off of
it. It's actually in very nice shape
for, you know, all things considered.
There's really no damage to it or
anything. It still looks like it's got
the original paint or coating or
whatever that is on it. Um, someone was
telling me in a previous video, if it's
yellow, don't touch
it. So, yeah, I just want to get this
all cleaned up. You see all the dust in
there? Um, and I we looked at this on a
previous video. We went under there.
that's potted. So, there's nothing in
there that we can mess with. But, it
looks like this will come
off.
Um, I don't know if I'm going to have to
remove this, though. Looks
like Looks like just the top will come
off. Maybe I'll mess with it and see if
I can get into it. But, I'm going to
leave these uh in the position that
they're in so that when we test them, if
we get one that's bad, maybe that'll
tell us something about uh what's going
on inside of it.
Okay, I got in there. So, I had to take
the uh two wires off of the
um what do you want to call that?
Indicator light. Dial light. Look at the
construction of this thing. Just look
how wellm made this is. So, they made
there's this tin well, it's not tin,
this steel, I guess, cover that goes
over it. And just look how they they
stamped an oval in it. They didn't stamp
lines in it. No, they stamped an oval in
it just so that it, you
know, I don't know why they would go
through the trouble to make it that
nice, but they did. Um, you know, I
guess they didn't want that to bend, so
they put a crease in it, but they didn't
put just lines in it or a square in it.
Now, they put an oval in it, right? And
then up here, there are just a couple
lines. And there's just, you know, it's
just so
wellmade. Just beautiful construction.
Same thing here.
All right. So, I just got inside of this
thing. Let me move this out of the way.
Let's see if we can tell what's going
on. So, there's a five gang tuning
capacitor. All right. Thank
you. Wonder what that went to. I wonder
if it was one of
these and they dropped it in there from
the factory.
No, it goes right there, doesn't
it? Yep. I'm sorry, Mr. Factory Workers.
I was just
kidding. I didn't think you'd actually
done that. So, my theory was there. You
know, I try to come up with my theories.
A lot of times they're nonsense, but I
was thinking maybe they'd lost one in
there. I went, "Oh, I just grabbed
another one out of the box to put it on
there." But no, that's not what
happened. All right, so I found my
missing part. Boy, isn't that great. So,
what do we have down
here? There's another one.
So that's just an adjustment probably,
right?
So, it looks like all of these can be
tuned with that adjustment. I'm not
going to tune any of them unless it
tells me to in the
manual, which knowing them, it very well
may. I don't see any
caps.
Oh. Oh, you know what? They're caps,
aren't they?
Is that what's going on? Those are the
actual caps. I mean, they're tuning
capacitors.
Hm. Yeah, maybe that's
it.
Maybe. And then there some part of it is
connected to
ground. Yeah. Is that what's going on?
These are the capacitors, you know, cuz
as you tune it, it changes the value of
them. I don't know. I don't see any
capacitors in there, though, that are,
you know, something that you could uh
that you could change or anything. Look
at the beef on the plates. Look at this
one, too.
It's out of place. I'm not touching it.
See how it's
bent? Will not be touching
that. Um I mean, I'll touch it, but I'm
not going to bend it back. Maybe it's
supposed to be like that.
Um, just look at the thickness of the
plates. I mean, look at
that. This thing is built literally like
a tank. I mean, it's literally built
like a tank. It looks like a
tank. I can't decide if
[Music]
um if they've painted it or if it was
painted at the
factory. I mean, obviously this was
under the that cover.
It almost looks like the entire
outside's been painted with something
else, but it could just be that that's
how it wears. I don't
know. I'm I almost think that it's like
some kind of
anti-corrosive, you know, coating or
something. I I don't
know. So, this little cover we're going
to take off after we clean it up a
little bit more because we need to
change the uh the voltage jumper plug.
All right. So, I'm just going to clean
this up and then I'm going to look on
the schematics and see if I can make
head or tails over whether maybe that's
our five caps because remember we have
those five jars underneath it, too. All
right. So, I tried to get all the dust
that I could out of there and wiped it
down a little bit. Everything's in very
nice shape. Um, and if you look at the
schematics, those are not the the caps
we're talking about. These are the
condensers they're calling them. Um, and
they show them right here. One, two,
three, four, five. So, one, two, three,
four, five. And it even shows that the
first
four have an
adjustment, which is this little thing
here. And the fifth one
doesn't. And then it shows
you however that after that that there's
one for the
antenna which is this one. So it all you
know but
we've these aren't that I don't think
these are that important but it would be
interesting to know where they are.
Right. So there's one cap
there, one cap there, and one cap there.
And I'd like to find them. So they're
under there's one under the last two
somewhere and there is one
under
H. There's three of them somewhere. I
don't know where they're at. They must
be on the bottom inside those cans
somehow.
Um all right. All right. So, I'm going
to put this back together and we're
going to test the tubes and then
whenever we get back down to the bottom,
we'll see if we can ever find them. Um,
I'm also, of course, I have to replace
the wire. So, we've got that left. So,
what we got left is we got to change the
voltage thing. We got to test the tubes
and we've got to uh replace the power
wire and see if we can find those three
caps. All right. So, I can't test the
tubes. I I have a uh I have about six
tube
testers, but none of them seem to want
to test the really old
tubes. Um this particular one, which is
an IEO
625, actually has the sockets for it. I
think I've got a couple other ones that
have the sockets for it,
too. Those sockets are the tubes that
we're messing with. But
um in particular this five pin one
here. But uh I don't have any I don't
know how to set it up. It could be that
you just set up the filament
voltage and get that right and then the
other part doesn't matter, but I don't I
don't I wouldn't think that's true. Um,
and
uh, the gentleman I got this from had a
bunch of the older tubes in the side
here that I guess maybe he was using
this one for those older tubes, but it
doesn't say on my reel here how to test
them. The very early tubes just had
numbers. Um, so we have we only have
three types of tubes here. We have G24
and I don't think the G is important. I
think it's just 24.
Um, so
24,
45, and an 80, which is probably a
rectifier. Um, so I've only got three
types of tubes, but I don't know how to
set it up. So without without something
telling me how to do it, I'm not going
to screw around with it. I might fry it.
So we'll just have to do it the old
school way and just see if it works. And
if it works, we'll leave it like that.
And um I can substitute in other tubes
and stuff. I've got a whole bunch of
extra tubes. I've got tons. I don't know
how many 24s, 45s, and
uh um 80s I've got, but I wouldn't be
surprised if I've got several of each.
I've got a bunch of those early ones.
So, we're not going to test that. I
think the one other thing I am going to
test is I want to test and I may have
already done it, but I want to test
um the speaker
coil to at least see if it's if it's
blown. Um so I believe I can do
that by checking resistance from here to
here and here to here on the plug.
So, the two outside pins and the two
inside pins, I should get resistance and
I can I should be able to write that
down on. All right. Well, so from
here to here, which is this winding,
I've got 392 ohms, which seems right to
me. From here to
here, which is this winding, I've got
6.6K ohms. That seems high as crap. But
I don't I don't know. You know, I'm not
used to a speaker this old, so maybe
that's
correct. Uh, but yeah, that's a little
scary. I do have a connection from here
to here and from here to here as well.
So, that's measuring
out.
[Music]
Um, yeah. So, I guess we'll see. And
it's all coming back to me, folks, on
these tubes. I must have looked at them
in the earlier video. You know more than
me because I filmed those videos so long
ago, but I just re-uploaded them. So, so
this must have been the one that was in
it. It's a Majestic
G80.
Um, and it has something broken off of
it. So, that one's seen better days. So,
I have found a couple more apparently at
some point. So, I've got an RCA here and
a
new National Union Electric. So, we'll
put one of those in. So, this one isn't
going to do much for us. All right.
Um, we need to put a new line cord on
it. And, um, I think that's about as fur
as we could go. We'll have to just bring
it up after that. Okay, folks. So, this
is how I did the caps. Easy
peasy. So, I just taped these wires off
in case somebody wants to go back in the
future. But that can is completely
disconnected. We could actually unbolt
it and take it off the
uh chassis if we wanted to, but
um so one of the wires was coming here.
Um this is
ground. So from ground to here was one
cap. From ground to here was another
cap. And that's not touching. It's not
even close to touching. And then this
one we had to fly a little bit. So from
here to ground is another cap. And
they're all
2.2 microfarad uh capacitors. So that's
good. Took care of
that. So the electrical cord comes in
through
here.
And it has a knot tied in it. And then
one lead goes over to here, which is up
to the
switch. And then one lead goes here. Uh
which is actually the the fused side.
typical, you know, I've heard that the
reason that they switched the neutral
instead of switching the hot, and this
is a transformer set, so it doesn't
really matter. But I've heard that the
reason that they switched the neutral
instead of the hot is because it um they
thought there would be like a popping
noise or something when you turned it on
or off if they
didn't. So, whatever. But I I like
leaving the stuff the way it originally
was to the best that I can, you know.
Um, now I believe though that our switch
isn't working, so I'm going to mess with
that and then we're about ready to fire
it up. I can't think of anything else to
do on it. I considered instead of flying
this line over to the ground, I
considered mounting it up here
electrically. That spot right
there, that is that green wire coming
over. So that spot right there is the
same as this spot right here.
And then you could put the you could put
the cap right here and put the ground
right where they're putting the ground
for that choke or whatever that is. Um
but then I thought this was a little
cleaner than that. Okay, so I've got the
caps done. Let me see if I can figure
out what's going on with the onoff
switch. Oh, I didn't show you the cord.
So it's a new cord. I believe it's
actually made in the USA, too. Isn't
that I hope so. Um, and it's pretty much
identical to the original cord, which I
guess that was the reason they do it,
right? Um, and I got to say the original
cord, it's all frayed and everything,
but
it is pretty quality. This was the part
that was inside the set.
Um,
well, this is the part that was inside
the
set and it's in really nice shape
actually. So, it would have been fine.
It was just once it got out of the set a
little bit, it started deter
deteriorating. So, you know, really
that's the the owner. They kept it in a
bad place for a hundred years. And uh
this is the original plug. And I cleaned
it up a little
bit. You know, there's not much to them.
And I replaced the little cardboard
thing that was
missing. And so it'll have its original
plug at least if it doesn't catch on
fire when we start. Look, folk, it's
going to be fine. I don't know what
you're so worried
about.
Um yeah. So I think we're ready to uh
figure out the onoff switch. If I can't
figure it out, I'll just jumper it for
now and we'll try to fire it up. This
video is getting long, though, so we're
not going to go deep into it, but you
can at least see if it's trying to
cooperate. Okay, so this is the power
switch. Look at this
thing. Okay, now look at this side of
it.
This is on the
top. Underwriter laboratory
inspected. It's a 1 amp
switch under 25 volt. And then on the
bottom, made in the
USA. All right. Are you ready to see the
most amazing design you've ever seen? I
don't know that I can hold it good
enough to do
it. Okay. So, that's
off and that's
on. It swings this spring loaded
thing from one side to the
other. Look at that. That's
awesome. So that's
on I can't hardly do it where you can
see it with one
hand. Well, you get the point. Whenever
you turn
it, it throws that thing back the other
way. It's all spring loed. All right.
So, I guess it's just dirty. I'm just
going to spray contact cleaner all over
it. Spray contact cleaner all over that.
And I think it'll work.
Um, it's just having a little
attitude. All right, folks.
This I I to be honest I this is the most
u frightened for smoke I've been on
anything I've fixed
uh radio wise. This thing is so old and
so kind of out of the realm of what I
understand that I don't really believe
that it's going to come up. Uh by the
way I did plug the speaker in. That's a
good way to fry it. Leave that
unplugged. Okay. So, uh, I I got the
switch working, cleaned it out a little
bit, and it worked just fine according
to my meter. So, what I'm going to do is
I'm just going to bring it up on the uh,
Variac, Veratran, mine is
called, and everybody keeps telling me I
need a dim bulb tester. Dim. I don't dim
them bulb testers. I don't even get it.
I've had 50 people explain it to me. I
do not get
it. If the thing starts
shorting, it's going to turn on the bulb
and then I'm supposed to sit there and
decide if the bulb's too damn bright or
not and then I'm supposed to change it
to a different wattage bulb and all
this. Or you could just put an amp meter
on it and see if it starts pulling a
bunch of amps. I don't get it. If
there's a short, that thing's going to
go
crazy and it tells you the same thing.
So, I don't understand why everybody's
so obsessed that I have to use the uh
dim bulb tester if I don't want to use
the dim bulb
tester. The I'm starting to see a lot of
um arrogance in some of the radio repair
guys. Not a fan of arrogance. Never have
been. Okay, so here we go. What do you
think? Is it going to do anything? I
think it might blow up some caps, but I
These caps are crazy. They're
2.2. You know, they're little tiny caps.
So, and if you're running the
voltage, 400 volts. H. What do you
think? I might have to order some with
higher
voltage. According to
this, 306 is as high as uh we get, but
depending on how this is wired, you may
end up with more than that
somewhere. But I have no I have nothing
to go on other than this. So 275 the
detector plate and then there is one
here that's 306 volts. As I understand
it, if I was to leave the the load off,
don't plug that speaker in, that thing
might run away and just go really high.
Um, and we don't want that. So, I got
the speaker plugged in. I tested this
the uh the resistance on the speaker
coil. So, I think all that's left is
just power it up and see what happens.
But, uh, if anything bad happens, what I
would expect to happen is that one of
those caps blows up and then I'll order
some more. Should I be wearing a blast
shield? I don't know. We'll see what can
we do here. Okay, so I've got the U
Veritran on zero
volts. I've got the ampmeter on the
mid-range. It's got three different
ranges that it can use. And the
um this thing, it says it's 105 watts.
So, that ought to be less than one amp
fully functional.
So, I think it's just it's big and scary
looking, but I don't think it's all that
powerful. It's just it's just an old
one, and this is how they looked when
they were old. I think it's just super
overdesigned.
So, that's off. That's on. So, we are
turned
on. So, I will slowly turn up
the Veritran and we'll see what happens.
how the
um we got rid of all the capacitors
except for those three that we couldn't
find those little value ones. Um so we
shouldn't
really have a short or anything to worry
about, but we'll see. So I'm going to
slowly turn up the voltage a little bit
and just see what happens with this. If
it starts pegging, then you know we've
got some
problems. Oh, she's alive. She's sucking
a little juice
down. So, we're at
50
volts. It would be
cool. I hear
something like a
I would describe that as like
transformer voltage. So, we're at 50
volts. I think we can leave it at that
for right now.
Right. I don't see any heater glow on
anything. I guess we could check
voltages.
But if we're only at 50 volts, we
probably wouldn't get much
yet. Can you hear that,
though? I mean, there's like that high
pitch
wine. All right. So, we're going to go
up a little bit more.
It must not be doing much because I mean
it's not telling me that it's drawing
any amps really, but we are on that
medium gauge there. Should I put it over
on the lower
one? Let me turn the voltage back
down. I don't want to swap it while
we're Okay, now we're on the low gauge.
Yeah, we got a little bit of action,
huh? Okay, we're
at 60
volts. We're not trying to reform any
caps or anything, you know. It's we
replaced all of them.
Okay, we're at 90
volts. We're still at less than half and
a
half. Got a nice
blue blue glow on our rectifier. And
we've
got glow here. It's a TRF set. I don't
know anything about those. So, it could
be like we've got one bad tube and it's
stopping the signal. But I do hear
something in the
speaker, but I don't think that the
volume is affecting it. Let's see if I
can get you to hear it.
Yeah, I don't know what we're hearing. I
don't know if I do hear it in the
speaker. I just I hear something. Okay,
we'll try tuning it just for
giggles.
Well, it's turning, but Without the knob
on it, it's really hard to
[Music]
You know, I don't even have the antenna
on up, by the
way. But you hear it,
right? So, she's trying to work. All
right. So,
That is actually about 120. It says 110,
but So now we get volume out of our
volume
knob. So our amp must be working.
[Music]
[Music]
All
right. So, we've got no antenna hooked
up and um I thought maybe it would just
grab something out of the air,
especially uh
WBT 1110 is four miles from here. It
literally like if one of the towers fell
over, it hit my house. So, um and that
signal is so dominant. Usually, you can
just pick it up on anything, but uh
apparently not with this. But I think we
uh I think we have safely got it back
up. Um I I need to test voltages. We
need to try to trace the signal through
it somehow and see what we can figure
out with that. We might just try
swapping some uh tubes in the IF and the
RF. Um there's just we can try aligning
it all that. So, we've got a whole bunch
of stuff left to do. We'll do that on
another video. So, I hope you enjoyed it
so far. Leave your comments down below
and we'll be back with one more
video. Hope you enjoyed it.
