It has battery damage, AND caught on fire twice, frying every single chip on the board.
Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's Classic Video Games back with another cool pinball repair video
for you this evening. We have been working on this complete basket case Bally supersonic pinball
machine. There's no way yours is in worse shape than this one, but we've been steadily working
through it. This thing had a fault where the 43 volts that runs the solenoids and the runs the
zero crossing detector on the MPU was shorted to the 5 volt line in the MPU. And by doing that,
they fried every chip in the game, we believe. We don't know about the displays yet, but when we
bought it, our buddy Jonathan got it for us. When we bought it, the lamp board was missing
and the solenoid driver board was missing. The MPU was still there,
sound board, and the displays in really rough shape. So today we are going to
repair that MPU board. What do you think? Don't even know if it's possible, but we're going to
try it. The reason this board was missing is because this is the board that turns the 12
volts into the 5 volts. So whenever that board shorted, it would have torn us all to hell.
And then the lamp board has a bunch of chips on it that I guess it must have been obvious on the
board that some of them had blown up or been damaged. Here is the sound board. Notice the
one chip has been burnt. The other chip has a big hole in the middle of it. It's a shame too,
because this PROM here is very... that's kind of what you have trouble finding,
because that has to be burned on a one-time burn PROM, right? So in other words, I can't do it
myself. I had to order it from somebody. The other ones are just chips that you can replace. So it's
not that big of a deal, but that one kind of sucks. And it's not crazy. It's like 20 bucks
or something. And they make new replacement boards. Our buddy GTO makes a brand new board for it.
But anyway, today we are going to work on that MPU. So we have done the rectifier board,
the transformer. All the voltages are correct here. They then travel up to here. The 12 gets
turned into 5. That is correct. The 240 or whatever gets turned into 190. We've got it set at 180,
so it's a little lighter on the displays. So this board is working fine. We pulled that out of a
parts box. It had a bunch of stuff missing. Put it all back together. So if you didn't see that
video, it was really cool. You ought to check it out. But now we're on to the MPU. So let me show
you what's left of the MPU because it was burnt up and then I burnt it up again because I didn't
know that the line was shorted on it. Oh boy, we got our work cut out for us. Let's check it out.
If you've been following the saga of the workbench, there's that screwdriver I lost.
All week long I've been trying to clean off my workbench and I have it cleaned
to where I can barely reach everything. Like I can't quite, you know. So that's pretty good.
It's getting there, but I want to go farther that way. Keep going that way. Okay, so this is the
board that was in it. Now when we first started the videos, this smoke damage was here already.
So this had already caught on fire. Now if you look, the chip has completely like just
melted down. Big problems. Okay, so I thought, well the chip burned up. We'll figure out what's
going on with that. Blah, blah, blah. We were working on the rectifier board and I was trying
to, you know, on the transformer and I was just trying to get the thing to work. We got it all
working fine and I plugged everything up. Sparks everywhere. Fire. It was like brimstone and hell.
It was horrible. When all was said and done, it blew a fuse and caused this smoke damage.
This fire damage. So the fifth pin up here was shorted to the fourth pin up here.
The fourth pin up is 5 volts. The fifth pin up is 43 volts. So every chip runs off 5 volts,
but instead of getting 5 like they wanted, they got 43. So wham! It was not happy. Big problems.
Okay, I've worked on a lot of these, so I think we can fix it. Now the damage here,
it was from the battery that's mounted here and that's typical on these Bally 35 boards.
The part number ends in 35, so they call this the 35 board. It's silkscreened right there,
but you can't read it because of the corrosion. So this one looks like it's real bad. It's not
that bad compared to most of them. Most of them, this corrosion rises up to like here
and eats a whole bunch of stuff. This one, the corrosion has only got up to like here.
It's not that big of a deal compared to how they usually are. This is just cosmetic. So we're
going to do the whole thing on this like we usually do and see if we can fix everything
that got smoked. Now, oh and let me show you the back. This is another reason I kind of want to
work on this particular one because the back's fine. So the place where the fires were is fine.
It didn't burn up the board. It's just kind of superficial stuff. This one's in pretty good
shape compared to a bunch of them that we get. Now you can buy a brand new board for it. They're
like 200 bucks. It's not that big of a deal, but I thought it would be kind of cool to fix the
original board. Here's just some more horror footage. Yes, that's a big hole blown out of our
ROM. What do you think about that? That's fun, right? Yeah, that one won't work anymore. When it does
that folks, it ain't working anymore. Look at this one, how it's cracked in half. Yeah, when it does
that, big problems inside. Okay, so but if you think about it, running 43 volts through a socket,
the socket's probably fine. We'll look at the pin that it runs through, but this is socketed,
this is socketed, this is socketed. This is the 6800 CPU. These are 6821 PIAs. Just pop them out
of the sockets. This is the 5101 memory for the CMOS, like the battery backup basically for the
high scores and settings. And not even all the settings, just actually on supersonic, none of
the settings. It just saves like bookkeeping information and the high score. This is the 6810,
which is the RAM for the CPU and the ROMs. This is a ROM, this is a ROM, this is a ROM. All those
are in sockets, so they might not need much work. This is a 555 timer, super common chip, no big
deal. And so then that leaves us with one, two, three, four, five, six, seven chips. Well, eight
sockets if we have to replace everything. So it's not that big of a deal. It's that, what are y'all
worried about? I don't understand the big, what's the big hang-up about this thing? Well, we'll
check back at the end of the video and see if I was right. But there was other damage. So there
is a cap here that is blown apart. That is a Mylar cap, not a Mylar, a Tantalum cap. But the thing is,
it's right in the corrosion area. You always have to replace that anyway.
This here, we might have to replace these. I've got all that.
We need to certainly clean all that up. This transistor, usually you have to replace. That's
part of, this is all part of the reset section. The 5101 and its socket, usually you have to
replace. So that's not a big deal. This resistor damage here is just heat from this. Very common,
it's on most of them. And that chip usually survives it. Although that chip's probably dead
now because of the 5 volt thing. I might have got lucky and like this cap blowing up or something,
I don't, I think the 5 just directly connects to all of them. But I might have got lucky and
there's a cap blew up or something that saved some of the chips.
And this up here is like clock stuff and another cap. So what we're going to try to do is,
I'm going to take off everything and clean it up, not everything, but everything that I need to,
and clean it up. And I'll show you as I go through what I find that's messed up.
We'll look at it in the schematics and I think we can kind of check off everything that the 5 volts
goes to on the schematics where we can either check to see if it's fine or go ahead and replace
it. And then we also have to clean up the battery damage while we're at it. And then we'll start
repopulating it. And the way these things work, some of these chips are involved with like making
the displays work. Well we don't need those to work yet, we just need the game to boot code.
So we need the CPU, the PIAs, the RAM chips, and the ROMs. So this,
which includes the clock and the 555, all have to kind of work to get the flash code to work.
There is a little LED right here that will flash a code as it goes through the boot up process
and tell you what's right and what's wrong. So there's a sequence of seven flashes that it does
and it tells you where you've got a problem. And then these other ones, maybe, I don't know about
we can look it all up, but these other ones, some of them aren't completely necessary to get at the
boot. But of course they'll be necessary for the game to run and for the displays to work and stuff.
So like everything, the way you handle a big problem, this is certainly a big problem,
is you just do it a little bit at a time. So the first thing I'm going to do is I'm going to remove
this socket because we're going to have to replace it anyway. And we're going to start cleaning up
this battery damage because that's the, in my opinion, the most significant thing that's wrong
with it. So yeah, so we'll start with that. And as I run into stuff, I'll make a little pile of
stuff that was obviously fire damaged and we'll see if we can clean the soot off. This stuff can
be conductive so you don't really want it to stay like that because it'll cause a short.
But yeah, so hopefully at the end of the video we'll have a completely working
MPU. Here we go. Okay folks, so what I do is I take a wire brush and I just go to town on it
whenever it's got the corrosion on the bottom of the board like this. I just go nuts on it. Now
that has the effect of breaking some of this stuff down here. But if it breaks,
you shouldn't have left it on there anyway. It was compromised. So like see this resistor here?
I've now broken the leg off of it by just hitting it with this brush over and over again, right?
But that just told me that this resistor was pretty weak. I did the same thing to this cap
and it didn't break. So that cap's probably fine. Same here. Same here. You can see where I've
actually removed some of the, you just saw how this was all blackened, right? I've actually
removed some of the coating on the resistor but it didn't break because it's still fine. It was
just dirty, right? This one did break. So you're not really losing anything by doing that. Yeah,
you're going to break crap off the board but it was all compromised anyway. It's a good way of
being able to tell, you know, we know this resistor that I just went nuts on enough that I
sanded all the black off of it, right? We know that that thing is physically still in good shape
because it did not break even though the one next to it did. So that's just my philosophy on it,
right? And just go nuts on getting all of that off. Now you can see that the corrosion is really
still there but most of the actual like the buildup and everything is gone. And that also,
you can kind of see how it spreads. So the battery was here. It spreads over this way. These were the
power lines. It usually doesn't go all that high over on this side but for whatever reason it goes
real high on this side. And once it, it'll kind of go up this ground trace and then it'll start
eating these, you know, but it hadn't got to that yet. So it wasn't, wasn't on a scale of like tens
the worst I've seen. This is like a four. It's not that bad. So same thing on the back. You're just
trying to get as much of the actual physical buildup and it'll, it'll, you know, it'll build up
off of the board. Just all of the corrosion. So you're just trying to get rid of all of that.
Another thing is if you're, if you're like we're going to remove this,
this chip, solder will not stick to this corrosion here. So that's another thing. We're trying to get
it as shiny as we can so that the solder can actually work on it. So I'm, next up I'm going
to try to remove this chip. Okay folks, so after getting everything cleaned out and everything,
you can see the extent of the damage. Several of the traces no longer connect to the holes.
Almost all of the pads on this bottom row are gone and the back is just as bad. So I'm going
to clean this up a little bit and then I'm going to use a socket. I'm going to go ahead and put
the socket back in. I'm not going to use one with a, with a frame. I'm going to use some of the,
the inline sockets so that I can solder to the top and the bottom
wherever I need to get a trace connected to it. Okay, so I've been pulling off some of the damaged
items and I've been checking all of the stuff that's on the board. These are the ones that
are testing a little weird but I'm not sure if it's because of the shorted chips or not.
I'm cheating. There used to be a place called Great Plains Electronics and they sold a little
kit to rebuild the, the reset section of the board with and it had a convenient little
list of all of the stuff down there in the bottom of the board. It had a convenient little
map of the board and it had a convenient little parts list of the whole board.
So I've been using that to check everything. Now I got to say, this socket was one of the
screwed up sockets I've seen on any of these boards and the damage wasn't that bad. So I
don't know what the deal is with this particular one but it took a while. So
it sure as hell ain't pretty. But basically whenever I took the old one off, corrosion
had just completely ate up all of the pads. So most of the pads are, were missing on this bottom
row and especially on the back. But I got it in there and I've been putting jumpers and
soldering and blah blah blah just making sure every single pin is connected and checking it
over and over and over again. And I had to solder on the top in some places and I had to solder on
the back in some places and put jumper wires. Let me show you that. We have four jumper wires on it.
Whoo lordy that's ugly. But I think it's going to work. I still have to address this a little more.
As I go through each part I'm getting rid of all of the corrosion. Then I'm going to give
it a vinegar bath. All of that, that's coming. But we're getting there. So I'm going through
piece by piece by piece by piece and I started working through here. I was able to clean up
that soot off of the board in this area where it was all black. I was able to clean it off.
I scrubbed it with some, just some Clorox basically like a cleaner with bleach and
cleaned it up as best I could. I was able to get that off. I haven't messed with any of this.
And I've went through each component and checked it against the chart what it's supposed to have.
All right I've replaced a cap, a cap, a resistor, three transistors and everything else seems fine
at the moment but we'll see. I also replaced the cap up here. Both of those were across the five
in the ground so of course they just blew all the crap as soon as they were fed the wrong voltage.
So next up I want to remove the chips in the socket and then I'm going to start desoldering
the chips that are on the board. It's safe to say every one of those is going to be fried.
So I'm going to remove every one of them and put a socket in its place. So that's next.
All right folks so I was able to remove the timer. This one, this one, this one, this one,
this one, this one, and this one. Also after I did that I checked all of the resistors and stuff
that I had that were measuring weird in circuit and these four no longer measured weird in circuit.
This one still does. It measures 12k but if I remove it from circuit it's the correct 120k.
So I'm going to look at the schematics just to see why that is. There's probably
something in parallel, well there's definitely something in parallel with it that's lowering the
the resistance as measured in circuit. But it's fine because if I remove the resistor it's fine.
I just want to make sure there's not another short on the board that I'm unaware of that I'm not
catching. So I was able to get most of that soot off of there. What do you think? Looks a lot better
doesn't it? So I'm going to look at the schematics at that resistor and then I'm also going to look
at the schematics just for giggles at chip U19 which is this one. This is the one that got the
double whammy. It seemed like it popped big time as soon as I plugged it up and it was already
smoked. Remember whenever we saw the board in the game, this is on your first video, you didn't see
it on this video, but on the first video when we saw the game I noticed that that it was smoked
and it burned up. And my thinking was, oh it ain't that big of a deal, they just had some kind of
problem. And I went ahead and plugged it back up after I got everything going and they had it
overfused and it smoked again. So it'll be interesting to see why that one seemed to have
got it worse than the other ones. Like this one for instance didn't even hardly look damaged.
There is a little bit of a burn looking mark there, but my guess is that that has something
to do with the zero crossing and that's why that one got it so hard. But let's look on the schematics
and see. Alright, so the 43 comes in, goes through a resistor, and then is measured as 21. But
our problem was it was shorted to the 5, right? So we got 43 on the 5 and it was right here so
it wouldn't have been the 21, it would have been 43. The zero crossing detector is actually U14,
which is this chip, which looked pretty good. But if you think about it,
now we're going to have to go farther into it because this chip obviously,
well no, I was going to say this chip can handle 21 volts but actually it can't. They lower it
to 4.9 with this diode. But the one that got all the problem was U19 which just gets 5 volts,
but it could be the nature of that chip. Let's see what U19 is. It's a 4011, so it does not like
more than 5 volts at all. U14 is a 4049. So U14 handled it better than U19.
Ok, let me figure out that resistor too. Alright, so the one that R2 here is supposed to be 120,
which it is out of circuit. When I put it in circuit it's now 12 or something like that.
But the way it's connected through here, I can see why it would do that. You have
a resistor here and a resistor here. I don't know if that base would just be connected to the
emitter or not, but whatever. You can see where it would be easy for when that's in circuit if
you measured from here to here. You wouldn't get 120k, you'd get whatever power it could get
through here and here given you your resistance. So I think that's fine.
Ok, so what's next? Hmm, starting to get scary. Next we have to figure out what all we need to
get the thing to actually boot. So I'm just going to put the minimal chips on it to see if we can
get it to boot. Ok, so I went ahead and put sockets in all of them. Starting to look a lot
better now. Just ignore that part. Ok, so the MPU we all know is a 6800 made by the great Motorola,
also known as William Spinball. So we know we need an MPU. Now this is the PIA,
the Peripheral Interface Adapter. Now the problem that we have is that the displays
don't work yet. And the lights don't work yet. So how are we going to know that the board even
works? Well, this little LED is going to be our only output. And that LED needs this PIA
to turn it on. So that's how we're going to judge if the board is working. We're going
to watch this LED. Now this LED runs off 12 volts. So if you power the board with its 12 volts and
its 5 volts at once, that LED will immediately come on and stay on. If the board actually starts
running code, the first thing it does is turn the LED off. So we will know if it's running code if
the LED turns off. So it gives like a real quick flicker. It turns on because the power goes to it
and then the CPU immediately turns it off. The CPU will only turn it off though if it's
running code. So of course we need a ROM chip for it to start running code. And the very beginning
of the ROM code is turn off the LED. So that's how we're going to know. That's backwards. Most
people, they don't understand this LED because they have it completely backwards. The LED is
always on. If the LED is off, that's only because the MPU is telling it to turn off.
So it doesn't necessarily flash. You see it as a flash but what's really going on is the MPU is
turning it off and then allowing it back on and then turning it off again. So it's kind of
backwards. Once you kind of get your mind around that, it makes it all make a lot more sense.
So with that to say, if I were to plug this into 12 volts right now,
even if I took the MPU out, that would just come on and stay on.
But we're trying to get it to turn off. That's the whole thing. So for the MPU to start running
code, the CPU to start running code, it has a few signals that it needs. So one, it needs a
ROM. So it's going to have to have code to run, which will be in the ROM chip, which goes right
here. And these two, but I think this is the only one you need to get it to start.
So it has to have a ROM. It has to have a code. It has to have power. And on the 6800, of course,
it has to have a clock. So the clock signal we'll look at in a minute. I think it's this chip right
here. And it has to have a reset line. So when the game comes on, this pin 40 on the chip
is high. It's at 5 volts. And this reset line holds it low to zero and then lets it go back
up to 5. And the... I may have that wrong. Maybe it starts at 5 and it goes low. Whatever,
we'll figure it out. It doesn't matter because it's going to do it itself. But the whole purpose
of that is to make sure that this starts at a known state and it just basically holds the CPU
turned off until that reset line goes high, which takes a split second, literally a second split in
the parts. One of those little parts, right? So the reset section is all this down here. Not this,
but all this stuff, right? Or some... I don't know about how much this. Yeah, this too. This
and this is the reset section. So you need that, but that's kind of hardwired into the board.
You need a clock and you need a ROM. I don't know if we need this 555. I mean, we could just go
ahead and put everything in it, but it's kind of... I'd kind of... because this may be the only chance
I get to do this. I'd kind of like to get it the minimal amount of stuff that you need to boot it
up. So let's see what the clock chip is. Okay, so here's the 6800. These are the outputs, you know,
the address bus and the data bus. And so as inputs, it needs power. Pin 40, it needs this reset line,
which comes from the stuff we were just talking about. The valid power detector
circuit, right? And then it needs these two clock signals,
clock one and clock two. So these come from U15, A and B, which is the part of, you know,
the two different sides of U15, and U16. So we need both of those. So we need U16 and U15.
Now I want to see what the 555 is doing. It's over here. It is the display interrupt generator.
My theory is this thing will run without that. It just... the displays won't work, but we won't know
because we don't have any displays anyway. Okay, so let's try U... we got to have U15 and U16
definitely. Okay, so U16 is a 9602, which I'm told is a dual monostable multivibrator.
Yeah, boy. Makes sense. Sounds like some kind of clock something or the other, doesn't it?
We've used those before, actually. I actually had one, you know. I think I remember replacing that
on a Williams board. And then this one is a 74S37, which I'm told is a quad two input NAND buffer.
And folks, this is new old stock stuff. I didn't pick that out. You know, I know some of you,
you know, this is going to make some of you quit my channel in a rage.
After I made that little joke about Canada being the 51st...
It was a joke, folks. Come on. It wasn't that... it... come on. It wasn't that big of a deal.
It's just a joke. I didn't mean it. It's just a joke. Y'all, if your buttons are this big,
I got to push it. It's going to be all right, folks. Okay, so we got that redone.
Let's figure out what these are and then see if we can kind of confirm that we probably don't need
them to try to get the flash. I want to see that flash and I only want to have a few chips when I
do it. All right, so U20 is used for the displays and it's just an output and there's, you know,
there's no two-way stuff going on there. So you don't need that. You just won't have any displays.
And then here we have U14 and U19, but they're just using them for the blinking signal. So
they're probably used for other things, I would imagine. What else can we get away with getting
rid of? U12, like we talked about, we don't need that. Okay, so memory enable... is that for the
battery? The memory enable circuit. I don't know if they're just using that for the battery.
Where is our battery? No, the battery is here on the auxiliary voltage to U8. Well, U14, like we
said, is the zero crossing detector, but that it doesn't check that till the seventh flash.
So I don't believe you'll need that either. So we don't need 17 and we don't need 20 for sure.
And we don't need 12. 12, 14, and 20. But unfortunately, I think we need about everything
else because some of these are down used down here on these ROMs. So the U7 is the RAM.
We're not using that at the moment because we're just trying to get the flash.
U6 is the 5101 RAM. No, U8. U8 is a 5101 RAM, which is using U18. Yeah, I don't know that we
can... I guess we could just try it, but we're going to need these because they're using it
to route some of the signal, like the address and data stuff. I guess you could work all through it
and just figure it out, like over here. It depends on what jumpers are on the board and stuff too.
But over here, you know, this wouldn't be needed unless you were using E10 for something.
And we're not. We're jumpering over E10. But that's just one part of that chip,
you know. So there's other things it'll be used for.
Okay, and U14, this part, wouldn't be needed unless you were using E25.
And looking over here, we are not. Okay, well that's cool. All right, I like it so far.
Then we've got this coming over here to E19. Are we using E19? I'm looking here on the board
as I go through it. Yeah, see we are using E19. All right, I'm just going to leave out the display
ones. E20 and I'm going to leave out, I mean U20 and I'm going to leave out U12. And I'm going to
leave out U14, which is the zero crossing detector. Unless U14 is used down here somewhere.
Oh yeah, that was that one we were just looking at. All right, 20 and 12. I think that's all you
can leave out. I think the rest of it you need because it's used for various clock signals. I
mean to route address lines and stuff for the ROMs. We're going to have to change some of those
jumpers and stuff probably anyway whenever we put the new ROMs in. Okay folks, I've got a power
supply, a bench power supply. And I've got a little connector rigged up here with the 12 volt,
5 volt, and a ground. And this isn't the best way to do it. I need to make one that's got a switch
where I can just turn it on and off. But, you see that? It flashed and then went back on.
You shouldn't really hot swap it like this. But do as I say, not as I do.
I'm just trying to illustrate the point here on video. Isn't the greatest way to do it
if you have a test bench. So sometimes it'll stick on like that if you're
playing with power like I'm doing. But each time I do it, it's basically
resetting the little quick flicker. And it's off because the CPU is turning it off. Also,
if you short pin 39 and pin 40 together, what you are doing is I now have pin 40 low
because pin 39 is low. So I'm forcing pin 40 low, which puts the MPU in like where it's
basically turned off. And then when I let go of it, it goes back high. The reset is now 40.
This goes back high and it has started the MPU. The MPU has started reading the game code in this
ROM and turned off the LED. So it's just the quickest flicker that's basically... I mean,
all that's happening is it's just starting to run the code. It's trying to run the first RAM test,
which is to check the EPROMs. And it's turning the LED off because it's going to turn it on to
communicate with me. So all that's going on right now is the CPU has taken control of the LED.
But what that means is our CPU is at least somewhat working. Our PIA is at least somewhat
working. Our LED is working. I mean, we knew that because it was turned on. And our ROM is
somewhat working. But we don't know... and the reset section is somewhat working. But we don't
know if the ROM is correct. We don't know if everything on the PIA works. We don't know if
every single address and data line on the CPU works. We just think so. But that first flicker,
for it to turn off the LED is the absolute hardest part to repair. So the next thing that it checks
is it checks the ROMs. I've only got one in there. This is a 2732 used one, obviously. I guess they're
all used now, right? Unless you find some new old stock ones. It's a 2732 that I've burnt new
software on. And I'm going to burn another one for here that is the game-specific software.
So on these PCBs, this one is kind of like a generic chip that basically runs all of the...
like it has the diagnostic code in it. It basically is the bones of the program that
runs. Because it's all the same. It's telling it how to display numbers. It's telling it
what the PIAs are doing and all that. It's like all of the basic code that is the same in
every Bally pinball machine. Or very similar, right? And then the one that goes up here,
sometimes in two different ROMs, like on our original board. Yeah, it had two ROMs.
So this is the one that's already in there. And these two were up here. Well, you can combine
them into one 2732 and put it here. So both of these can be 2732s or 2532s. But depending on
what chip you're using, you have to change the jumpers on the board. So this is a jumper.
This is a jumper. This is a jumper. There's some more here. And Bally has released all of
that information and tells you every little thing. And it's also just basically in the
schematics. If you look, it shows everything. We saw that earlier. All that to say, I've got
it jumpered for two 2732s. I burned one already. I'm going to burn the other one. And what that
should do is get it to where when we turn it on, it does the quick flicker, which is the CPU
turning the light off. And then it will give us one solid flash to let us know that the ROMs are
good. It's not doing that yet because we don't even have both of them in there. So that's next.
All right, so I've burnt the other ROM. And again, we've got everything jumpered properly.
We've got power on it. There's the LED. I'm going to do the reset basically by shorting the
pin 40 to pin 39. All right, so it's held low right now. So it's as if we have just gave it
power. Now it's hard to understand that. That is actually a flicker and one flash.
The flicker part is very confusing. A better way of thinking about it is because again,
as soon as it gets power, the LED is going to be on like this. So a better way of thinking about
it is it turns off and then flashes once. Off, flashes once. That is one flash. But the turning
off is that when it first comes up, you'll see that light come on and then go off immediately.
So going off, they call it the flicker, right? Because it had a little bit of light and went
off. So there's the first flicker. That means that the power is right. The LED is right. It's
starting to read this code. And then the one flash is it saying, hey, your ROMs are good.
I'm just doing just a checksum. So we are starting to walk through the code, the flash code. So the
So if there is a problem, I'll resist the rest of that. If there is a problem, yo,
this one will probably be it. All right, I always get those two confused. But the second one is the
6810, which is just the regular RAM that runs the ROMs and the code. And then this one is the 5101,
but I can't remember which one's two and which one's three. Number two, or so the next one in
order is the 6810. And so it will be the second flash. So if I can do this quick enough, I won't
have to use the screwdriver. One, two. And so we'll try it again. I really shouldn't be doing
it this way. I'm trying to basically hot swap the power. The problem is whenever you if you so if
you pull the connector off and then put it back on, you're giving it a very weird, you're not
just switching the power on, you're you're giving it a little bit of the time. And it's not happy
with that. Now I don't have the 43 wired up to it. So I'm not running the risk of that. But
one, two. The reason that it waits a little bit before it does the second one is because the
way that it checks the 6810 is it does like 36,000 math computations or something like that. So it
goes to the first little bit or whatever and it writes a number in it. And then it says what's in
what number is written in bit one, and it reads it back and then it goes to the second bit and it
writes a number and it says what number is written in number in bit two, and it goes all the way
through and it's like 36,000 bits or something like that. So it's doing a ton of math. And of
course, it's doing it at clock speed. So it's just doing it's it's just doing so much math that it
actually takes a little while for that for that test. It checks the ROMs for the first flash
really quick. The the math that it needs to fully check this RAM takes a lot longer. Now if you're
if you're doing this and you're trying to repair one and you're not getting that second flash,
it could be this chip too because a lot of the signals to these two chips in particular
come down through here. So you can see that I actually had to repair one. There was a
connection through from here over to here and then it comes up here and then comes up to here.
So some of the connections for the 5101 are also the connections for the 6810. So if you don't get
that second flash, yeah, it's this chip, but it could be one of the signal lines running through
a really screwed up socket here like we've got where it was just trashed. It's very common for
this to have serious problems. But the third flash, the next one is in fact that one. Now
keep in mind, we don't even have the 555 in yet. We don't even have this other PIA in yet
and we don't have this one chip up here that we know for sure U20 is only used for the displays.
So it's an output. You don't actually need it to boot everything, which just goes to show you if
you have a problem with this, it's not that, it's not that, and it's not that. It's, you know,
something else. All right, so let me put a 5101 in and see if we can get our third flash.
All right, so got the 5101 in. Let's see if I can get hot swapping. One, two, three. Bam!
That's what you want. Let's try it one more time. One, two, three. See how there's a little pause
between this before the second one because it's got to do all that math. And then it just told
us the third one's good. If you cannot get that third flash, you've, if there's any corrosion at
all, you've got a problem with these lines that hang down low on the board. So you've got these
right here and these here that jump over to here. There's also some here beside it that connect to
this chip and then go up here to a couple things. All right, so you've just, you've got a bad trace.
If you look in the schematics and check your, your address lines, you can just check, you know,
like A3 and see where it is over here on the ROM and just see if the A3 pin on the 5101 is
connected to the A3 pin on the ROM and on and on and on. And if every single one of them is
connected where it should be, it should work. If it still doesn't work, you've probably got a couple
of the lines connected somewhere. Usually though, if you've got a couple address lines shorted
together or a couple data lines shorted together, you won't even get the first flicker on the ROM
because it, it can't read the ROM because they've got a couple address lines shorted together.
So that's another thing you can try if you just can't get it to work. And this is, you know, I
realized by this time, this is for people that are just wanting to tinker with these old boards
because you can buy a brand new board and that's what 99% of people do now. But if you, if you've
got one and it just, you cannot figure it out, check all the address lines and see if any of
them are shorted to each other. So is A3 shorted to A5? Is A3 shorted to A6? Is A3 shorted to A7?
And then check all the data lines. Is D1 shorted to D2? Is D1 shorted to D3? Is D1 shorted to D4?
I want to know when it goes. Okay. So that's three. Now the fourth flash is this 6810, the 6821
that goes here. And the fifth flash is the 6821 that's here. It's just a more extensive test.
So whenever I put the 6821 in here, we should get our fourth and then our fifth flashes.
So I've installed a 6821 here. Usually you don't get any trouble out of it. As long as that thing's
good. The socket's usually fine because there's nowhere near the corrosion zone. And this one,
by the time you get up to this flash, you've kind of tested it a little bit with this
LED. So let's see what we get. One, two, three, four, five. Okay. All right. We're doing really
good. All right. So the sixth flash is checking this display interrupt generator. And it's just
a line that it needs to make the displays work. And that of course is the 555 timer. It's very
common on this for the timer to actually be fine, but for this cap or this resistor to be
all corroded. So one of the legs isn't working right just because of the corrosion stuff.
But you know, in ours, we had a different problem where we had fried every single chip on the board.
Let's see what we get. One, two, three, four, five, six. All right. So we've got all six.
All right. Now the seventh one, we can't test because the seventh one
is the one that caused the whole freaking problem. The seventh one is the zero crossing detector,
which was the solenoid voltage into the board. You can do some little cheat stuff and mess around
with a five here or something. But the way we're going to test it is we're going to test it the
old fashioned way. We're just going to put it in the cabinet and see if the thing will finally boot
up. All right, folks. So we still got to do some work in the cabinet. We've got to repin some
connectors and stuff before we actually try it in there. But I wanted to show this. David sent us
this little IC pin straightener in. That's pretty cool. So basically, whenever you buy new ICs,
the legs are all splayed out usually. And this little thing is like a little
cruncher. And it does the wide ones and the thin ones. So you take... I don't know if I have one
that's... That one's kind of stretched out. This is a screwed up one. This is one of the ones that
was burnt up. Put it in there. Squeeze it. And now they're all straight. That's pretty cool. So
thank you, David. We appreciate that. But leave your comments down below. Let us know what you
think. I think this one is a good little base. And we worked through fixing every little part of it.
We'll keep working through the pinball machine on the next video. And we still have to mess with
the displays. We still have to mess with the lights. Check all the switches. All of that
crap. So we got a long way to go on this thing still. But I hope you enjoyed it. We will see
you on the next one. Now, if you want to see us do more of this board repair crap,
if you're not completely tired of it, check out this video. Good old Bally.