Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool video for you today this is a
repair video we've been wanting to do
for a little bit this is the gantry out
of the trolley they call it different
things out of a old Drew's Packer Paul
crane machine so this is from like the
mid 80s
since the claw I was gonna show you how
to fix these electric motors so
basically on this one whenever you turn
it on nothing happens so you can't the
boards working because the little LED
comes up and everything but you can't
get anything to move so if these have
been sitting a long time you've got
problems with the motors probably so you
can either have a motor that's burnt up
or you can have a motor that's just
dirty it needs to be clean so I'm gonna
show you how to clean them so basically
all of these are electric motors and one
of them which is this one I believe must
see yeah this one this is the back of it
of course this is the motor that raises
and lowers the claw and you can see that
the claw is completely extended it was
laying in the bottom of the cabinet like
that because the motor would not pull it
back up and then you've got this one
which turns a wheel on the other side
which makes this wheel move which moves
the trolley back and forth so this is
the one that makes it move back and
forth I missed it and then you've got
this one which turns a wheel over here
on the side which makes it move along
the tracks inside the machine so it
makes them move forward to back so these
are just little electric motors and then
there's a little gear box on the bottom
up so the way you test these things out
is you unplug the wires if they will
unplug on some of them they might not
come off so you could probably check it
while it's
still plugged in and then you use a
multimeter to check the resistance I
forgot to grab the multimeter be right
back okay so if the multimeter set up
I've got it on ohms or testing
resistance and this inside it has a big
coil and brushes so we're going to check
the resistance between the two pins so
the resistance between the two brushes
is several K which means several
thousand ohms six seven so it's eight
thousand ohms it's just not you know
that's a very high so now we're at four
hundred and eighty ohms because I've got
it a little bit better so it shouldn't
be anywhere near that it should be down
below like ten ohms you know take it
apart and show you how it works if you
the other thing you can get is if you
test it and it's really low it's below 2
ohms or so then the motors burn up
it's shorted and if you take it apart
and look you'll see it all burnt up
black where other things over eated
these are just electric motors like your
in your ceiling fan and stuff like that
so the way you clean it some of them you
can do this some of them you can't this
one's got like a little sticker here on
the side I'm going to just cut the
sticker off so that it can come apart of
course it'd be easier to do this with
something besides a blunt screwdriver
but it's just a little label razor blade
or screwdriver or anything will cut that
and then as you can see there's two
screws in the top
they'll come all the way in so you take
them out and then this top piece will
come off most of them you can see how
it's pulling the brushes off too if you
can get that to come loose sometimes you
can sometimes you can't
I are a success so we took the cap off
and then there's this little these are
the brushes so we'll just take them off
so the way those work are they just
squeeze around these contacts here and
then you've got this which is a couple
magnets so this is called the stat or
because it's stationary doesn't move
just magnets and then this is called the
rotor because it rotates so the way that
the way these motors work is power comes
and through these brushes alright sit
since voltage through the brushes are
connected on the other end they are
touching this rotor which I don't know
if I get that out of there or not no
it's it's stuck in a gearbox so I'm not
going to take that out but perhaps I can
zoom in disregard the Nintendo 64 games
need some focus there we go alright so
see these bands here that's what the
brush rides on and so the brush connects
to these little metal pieces which are
connected to these wires the coil right
and so it sends the different voltages
for each one but so it's on this one I
think I think it sends 30 34 volts or
something like that 36 volts through it
and what it does is it turns this into a
big electromagnet so this is inside
these magnets there's something stuck to
it so you can see it's inside these
magnets and it makes it spin because
it's repelled by the magnets right and
then once it spins the contacts come off
of that contact and move on to the next
one the brushes and once they're on the
next one it is reversed to polarity so
now it spins trying to get away from the
other magnet and so you end up with the
thing spinning around really fast and
different ones have different
revolutions I mean rpms and all that so
what we're going to do is we're going to
clean those contacts and we're going to
clean the brushes so and they'll all be
a little bit different the way we do it
there's just a little piece of sandpaper
and you're just trying to basically
those brushes degrade their there I
don't know what they're made out of but
it comes apart basically so you end up
with a bunch of dust between the brushes
and these contacts that it needs to be
one
these ones aren't really all that dirty
but you can see there was a little bit
of dirt on it and then we're gonna take
the brushes and like I said these can
wear down but these are still in good
shape they're just dirty and we're going
to take our sandpaper and just clean it
up a little bit now you see how its
rounded so that it can hug net so we're
not trying to destroy it and we just
want to get the dust off of it it might
be smarter to just clean it with Windex
or something but you know you don't want
to sand it flat or anything like that
we're just lightly trying to clean the
gunk off of it
so
can't really tell how clean they are but
you just clean it I'm up a little bit
[Music]
they will snap back on that rule I'm
just test fitting it right now but they
will be like that you know and so you
measure let's see if it's any better now
all right so we've got 12 votes or
something like that so and that's what
me just barely touching it so that will
get it clean so what I'm gonna do now is
we're going to put it back together and
then once we get it solid again we'll
test the resistance and make sure
everything's cool and I usually just
wipe out the inside of this just to make
sure it's fine and wipe off these just
to make sure they're fine there's
nothing in it gunking it up and then you
slowly put it back together so I'm gonna
do that real quick and then we'll test
it okay folks so we put it back together
and I also went ahead and did this one
this one I had already done and so you
can see now we have like 10 ohms
resistance or 8 ohms resistance if I get
on a little bit better and on this one
over here we have something similar
that's much more like it
the sticker on the side says 24 volts so
that's what it's running on but it's
it's actually if you measure it in the
machine that's higher because it's
unregulated it's like 34 or something
like that and it says 65 which I believe
is the RPMs and this has 5 to 1 ratio so
they're talking about the gearbox for
every five times this turns it turns
that one time no I'm sorry
sixty five point five to one ratio so
every sixty five point one times this
turns it turns the gear one time and the
date on it is January 12 1987 this
little cap here I believe is to start
the motor it needs a little extra jolt
whenever it starts to get it moving and
so they all have a little cap on it we
broke this one someone replace it but
we'll put it back together and then
we'll try it in the machine and see if
that helped any of our motor problems
okay folks we have put it back in the
machine this is an old-school tiger Paul
crane right so let me see if I could
move the back we can see it a little
better so we've got it back in the
machine wired back up we're gonna coin
it up and let's see if our motors work
you can probably tell that we've already
tested it because the calls up that
fixed our motors and finally the last
one this is one of the real early ones
where you can move it after you drop it
believe it
[Applause]
alright let it win anything
but as you can see that fixed our motors
so if you have an old crane machine and
the motors are not working
check your fuses check your voltages if
you know how to do that and just see if
you're getting voltage to the to the
motors and then do like we showed test
them see if they're burnt up and test
them to see if they're just not making
good contact so just so we're clear what
was going on was the motors had power
going to them but the power wasn't going
through those little brushes there was
some resistance there because they were
they were dirty at the end so we cleaned
that up now they're making good contact
with the metal like they should and the
power is getting through and making the
motor spin and work so only only sold
ones a lot of times you run into the
problem where you can't get a
replacement motor because it it just
it's so obsolete this thing was the
motors have a date of 1987 on them so if
I checked if I searched for that part
number on the motor I might find one but
it might be kind of hard to but I didn't
need to find one they just needed to be
clean so I hope that helps you get your
old crane machine working now if you
like videos like this repair videos or
videos showing these old-school cranes
or old school arcade games or old-school
pinball machines subscribe to our
channel here because we do this stuff
all the time we've got a video game
store in downtown Rock Hill South
Carolina which is about 15 miles south
of Charlotte North Carolina chock-full
of arcade games pinball machines
jukeboxes and a few of these cranes we
don't get a ton of them in so we sell
these to people for their home game
rooms you can check out all the games
that we have available on our website at
lions arcade comm link is in the
description below where you can stop by
and see us like we said we're in Rock
Hill South Carolina but I'll leave your
comments below let us know what you
think about this if you have any
questions about fixing your crane motors
we call them cranes a lot of people call
them claw machines if you have any
questions about it hit it something if
we've got time we'll answer them to the
best of our ability
we'll see you on the next video