Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
alright folks this is Joe's video games
back with another cool arcade game video
for you this is actually a pinball video
related video but I thought it'd be
interesting to people with a game room
and it's real simplistic so if you're an
expert on pinball machines you may have
no use for this video but for people
that are just starting out I thought I
would show them this I'm what I'm gonna
show is the different boards that are in
a Bally pinball machine this is actually
a stern pinball machine but if you know
anything about the Stearns you know that
they ripped off Bally and did the exact
same thing that Bally did so basically
the boards and a stern pinball machine
are extremely similar pretty much
interchangeable with a Bally pinball
machine and these these when I say Bally
pinball machine I mean the ones from the
late 70s which were the first
solid-state games that came out in 77 up
till about I think 83 or 84 was the last
that they used this particular board set
so basically if you get a game that's a
valley or ass turn from that year those
that range of years this video will be
useful for you so there's about in most
of the games there's at least four
different boards that make it work
sometimes five or six depending on what
all the games capable of doing but I
thought I would show you how we repair
them and the way that we work through
them now this is an old game that we've
had laying around for years and we've
been working through it and getting it
going again pretty much got it done but
we still got a few things left to do but
I figured it'd be a good one to show you
one even though it's a stern like I said
all of the games are almost all of the
boards are almost identical so this is a
stern meteor basically the power comes
into the cabinet and this is the way
that you troubleshoot these you
basically start at the beginning so the
power comes into the cabinet and it
comes in the back and you can see right
there you have a little line filter and
that thing on top of it is called I
think it's called a very varistor if
you've got a game and it won't do
anything and you can't even test power
on it make sure that things not burn up
it's basically used to stop you know if
the line gets zapped by lightning or
something like that that thing will burn
up and
the game will no longer work very
interesting but the power comes in and
you can see that it's all kind of doing
its thing back there and then it runs
along this bundle of wires
appear to the front and runs to the
power switch and so most pinball
machines have a power switch right there
underneath the right side of the cabinet
see reach under here with your right
hand and clicking on now there's also on
most pinball machines over here a little
service tab so basically you can plug in
a soldering iron or something right
there and use it to power that even with
the switch off so that I guess it would
be more accurate to say that the power
runs from that the line filter up here
to this and then to the switch but the
switch turns on everything so basically
the power runs from there over to this
big transformer now in the Stearns the
transformer is usually in the bottom I
think I think on all of the Stern's it's
always in the bottom on the Bali Games a
lot of times the trend the transformer
will be right up here in the back box on
the right side in some of the Bali games
the transformer will be in the bottom so
just you know it's easy to see it's a
huge copper cord it's basically if you
don't know what a transformer is
basically there's Mack I don't know if
it's magnetic but basically you've got a
ton of windings in there and it creates
different voltages so it steps down the
voltage from the wall voltage to several
different voltages that the pinball
machine can use and basically usually
you don't have trouble with that usually
you don't have trouble with your power
switch either sometimes you'll have a
transformer that's burned out but not
often I'm talking one in a hundred
machines may have a problem with the
transformer now if you've got wires
broke or something that's a problem yeah
but just inspect that see if it looks
good
the way you can tell if it's melted down
sometimes they'll
they'll short inside and if you look
under the transformer you'll see a bunch
of gooey looking it almost looks like
wax basically and the reason it's like
that is basically the transformers
gotten so hot that it's burned all of
its wax off the inside that we're
talking thousands and thousands of
Revelation revolutions that the copper
wires in there basically it'll burn all
of the wax off and it'll puddle
underneath it you'll see little
droppings under it of wax if your
transformers melted down then you'll see
that but usually they're alright so they
send some voltages over here to what's
called the power rectifier board this
one's had a little bit of work done on
it some of them will have more work done
on it already by the previous owners or
it'll be a slightly different board
there are some boards that are a big
square board with three or four
connectors on it that pull off if you've
got that you know you have different
ways of servicing each board but they're
similar but this is the one that was
used in most of the early ballet games
and probably all of the stern games
basically it holds your fuses what it
does is it takes the voltage off of the
transformer and they call it the
rectifier board because it runs them
through these bridge rectifiers so it
creates five different voltages you can
see at the top it says test point one
test point two test point three test
point four test point five you know I'm
not gonna go through what each voltage
means but basically if you're having
problems with something always check
these fuses and you can find a list
online to see what the voltages are
supposed to be
you've got five different checkpoints
there basically one of them is running
the display voltage for the displays and
it'll be high like around 200 volts a
little bit less maybe one of them is
like a six volt that runs to all of the
lamps on the playfield the general
illumination one of them is a twelve
volt that usually will be high - it'll
be thirteen or fourteen but one of
them's a twelve volt that runs up to the
solenoid board that gets turned into
five volt on the solenoid board which
we'll show in a second
you've got one fuse one here two one of
these fuses is just the main line fuse
and then there's another I think six
volt DC which I believe runs the
switches but I usually don't have
trouble with that one so let's check
those fuses and check your your power
your test points here to see if you've
got off of your voltages one of the
voltages is AC that's the one that runs
the the general illumination but
basically most of your problems as far
as if the game won't do anything will be
on this board you'll have problems where
the bridge rectifiers have gone bad and
are blowing fuses problems where you
have really bad connections on these
pins on the bottom when these connectors
problems or these resistors have broken
etc etc you can't really replace this
without soldering though because they
make new boards but you have to solder
them in so this is this is intended just
to show more of an overview I'm not
going to get too much into exactly how
to repair them but once you kind of know
how the machines work a little bit it
can help you it can help you
troubleshoot and figure out what you
need to do next so once the power is
rectified it's sent up to the the top of
the game so this one's actually up and
running right now I've got all the
displays working I'm gonna open the back
and show you what the boards in the back
dude now basically there's a little
latch over here to open and all the ones
have different ways of opening it but
usually the the back glass if you turn
the key on the back or on the side you
can lift up the back glass out of the
channel and then pull it forward
be very careful if you break the back
glass that's the absolute worst thing
you can do on a pinball machine so that
power that we saw on the bottom goes the
different places but one of the places
that it goes is up here to this solenoid
board as it's gone now the solenoid
board gets its inputs I think they're
all come on I think they all come in on
this connector and it basically you'll
see there's several different test
points on here and most of them are
on this board they're actually
identified but on a lot of them they're
not but this board creates the it takes
to 12 volts and this little area here
turns it into five volts which is what
all of the IC chips on all other boards
need to run and sends it back out
through the connector over to the main
CPU board another thing that it does is
that it's it's responsible for grounding
all of the solenoids on the board so the
flippers the any of the drop targets the
kickers the pop bumpers ba-ba-ba-ba-ba
the coil that kicks the ball out of that
out into the out hole all of these
little transistors down here run that on
all of these boards you have problems
where the connections get bad after a
while so a lot of these connectors you
have to replace the connectors in them
and then also resolder the things on the
back but whenever people talk about a
solenoid board this is what they're
talking about now up here on the left
you see this area here this is actually
this cap here helps the 12 turn into
five it's a it's a filter cap for the
five volt but all of this stuff on this
side is to create the display voltage so
it comes in at like 220 volts something
like that and it is its adjustable
there's a little potentiometer here
where you can turn it down you basically
want 175 180 volts something like that
going over to your displays which are
mounted on the white board here so it
basically creates the voltage that runs
those now a lot of games are getting
switched over to the new LED displays
which typically do not need that
well definitely do not need that hundred
eighty volts so this Center here is for
to create the display voltage all of
these connections here here and here go
to different solenoids on the on the
game alright so the 5 volts that's
created by this section runs over here
to this board which isn't mounted in
there as well as it should be what put a
couple screws in it this is the main MPU
board this is what is basically the
brains of the
game on a ballet or a stern so as you
can see it says stern down out there at
the bottom this is an MP u 200 which is
actually the second revision on Bali
they only had their well they had two
revisions on Bali - now that I think
about it but basically what you're
looking for here is down at the bottom
where I am highlighting there is usually
a battery and if it's not been dealt
with basically that battery will you can
see how this board has damage to it
that's been repaired that battery will
eat up traces all over this and it's not
acid its alkaline which is actually the
opposite of acid but it corrodes
everything and it will destroy this
board the whole bottom of it and start
even destroying the wires which makes it
where you don't have a good connection
so basically if you're if you open this
up and you see a bunch of corrosion
right there that's your problem that's
probably the reason the games not
working you also have a little LED right
here on the board that blinks whenever
the game comes on if you look at that
LED and count the number of times it
blinks it will actually tell you what's
wrong with the board so you have four
connectors well five connectors five
connectors on this board this one down
here is for switches this one up here is
for switches and so basically those two
columns are telling all of the they're
the switch matrix so they basically are
they can tell whenever switches closed
depending on which wires run to which
switches right here on the right you've
got all these dip switches which is how
you change the settings in the game
which lighting was a little bit better
here for you but that connector on the
bottom left is how the power comes in to
the to the mpu board so that's very
important it's also how the solenoid
data leaves the MPU board so some of the
connectors there I mean some of the the
pins there on that left connector run
back over here to this connector and so
that is the computer that is the
computer telling the solenoid board
which solenoids to make work so
basically you hit a switch
like this this kicker here on the left
the slingshot you hit that switch
together BAM the computer tells what
these two connectors here that you made
that switch connect it calculates what
it's supposed to do and sends a signal
out through the solenoid wire which
comes over here to the solenoid board
BAM and tells one of these chips hey
make that left kicker fire and so one of
these little transistors is turned on
which grounds the solenoid maybe it's
one of these which connects back under
the play field and instantly makes BAM
the solenoid work and it all happens
super super super super fast as
computers are ought to do this connector
up here on the top left of your MPU
board is the connector that runs all of
the displays so basically it's sending
information to the displays to tell them
what to display which is all basically
only useful for for the scoring
basically and also the ball in play and
the match and then up here at the top
you don't always see this one even
plugged in but these ribbon cables that
are plugged in run over to a sound board
on meteor so there's a sound board
mounted there on the side this will be
the strangest part of whatever pin ball
you yet because the sound boards were
there were a lot of different versions
so there's probably 10 or 12 different
sound boards that you might find in a
machine over that era that we talked
about just because there were so many
innovations and sounds so you some will
have a speech component some of them
will be a real simple sound board some
will be a more advanced sound board the
Bali sound boards are completely
different from the stern sound boards
the Bali boards with speech are
completely different from the stern
boards with speech so that was one area
where they differed but and and on the
some of the Bali ones they don't plug in
at the top like this so the ribbon
cables is usually a stern thing but
that's the sound board over there on the
left and then down here at the bottom is
the last board that we're going to talk
about this is the lamp driver board also
known as the most reliable board and the
whole thing usually you don't have that
minute that much trouble out of it you
have these little transistors on here
and you'll see these they look different
you'll see different boards that look
different there's about five or six
different variations but they all work
in all of the machines even if they look
different as far as I'm far as I know
but if you have a lamp that's not
working like a light that won't light up
typically it's either a bad connection
on the socket underneath the playfield
or it's a that's that's usually the
problem by the way or it's a bad
connection on these connectors again
some of these you might have to replace
the actual pins inside the connectors
and resolder the connector on the back
if after all that you still can't get it
to work you can test these little trans
transistors and those do go bad but you
know not too often so there you go so
you got the power comes in goes to the
transformer goes to the rectifier board
the different voltages from the
rectifier board run to wherever it needs
to go but one of them the 12-volt runs
up here to the solenoid board which gets
turned into five volt and then five
volts and 12 volts run over here to the
O the other voltage I was talking about
on the bottom is the solenoid voltage I
forgot about that to make all of the
coils work and so the 12 volts and 5
volts and the solenoid voltage runs over
here to the mpu board through that left
bottom connector and makes it do its
thing look for a battery watch your LED
there to see if if you have problems
watch the LED and it may tell you what
the problem is if you've got a if you've
got corrosion you've got more problems
than you know about so you're gonna have
to replace a bunch of connectors and
things but if everything looks clean
watch that LED and see what it's doing
the lamp board down here and then
sometimes I have a sound board up there
on some of the valleys you'll have the
sound board right there and just in
various places and then you've got the
little display boards which are doing
their thing
they're all just connected with these
little connectors most of these are
pretty interchangeable the Bali and
stern ones are with the only difference
you'll see is in the number of digits
some of them have six digits some of
them have seven digits some of them will
have a comma some of them won't but you
can use them in any of the machines so
there you go I just thought I'd showed
it shoot a little video showing you the
different boards and how they connect
together and do their thing now if you
have a problem with a specific board
maybe now you can narrow it down or if
somebody says hey take your lamp driver
board out maybe maybe with this video
you'll be able to tell which one that is
so subscribe to us here on YouTube we're
going to be shooting a ton more videos
and we'll we'll see you on the next
video hope this helps