Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
previously on Joe's videogames
and so it is back from the dead still
needs a ton of work but so there's a ton
of light bulbs burn out so the next
thing I'm gonna do is I'm gonna pull off
both of these light boards and work
through them same cut the same type of
thing we need to resolder the connectors
we need to check all the transistors to
see if any of them are testing bad on
the bench and all that so I'll work
through those next and then we'll see if
we can get most of the most of the
lights lighting up like they're supposed
to so we put the board's back in and not
all of our lights are working so I'm
going to you know of course it could
just be burnout bolts so I'm going to go
through and work all of the bulb sockets
underneath the plate filters like a
hundred of them look at all that tons of
them some of these screws and stuff here
are from the parts that go here too
we've got it all kind of apart but
basically the balls fall back down on
this they roll down to a plate which is
this there's a little motor that moves
them around they work their way down to
here fall down go over here this wheel
turns around with another motor lifts
them under the top they roll down yet
another piece that's up there and drop
at the top of the gun to be shot again
and we got the little fan here that
isn't working so I gotta figure out
what's going on with that
so but the next thing I want to do is
I'm gonna get all the lights doing their
thing so I'm gonna go through and check
each bulb and buhbuh buhbuh blonde
change the sockets and get as many of
them going as possible so I'll come back
whenever we get all that taken care so
we have lights so all of them are
working except for over one
now that one's out again but his knees
twisted this one I can't get to work
it's like number 70 but all the other
ones are working so this thing's
actually trying to cooperate you can
hear the sound that's the soundboard
trying to tell me fix me next fix me
next and the whole game is trying to
Christine itself and bring itself back
to light one of those one of the lights
started blinking let's see if this one
will do anything or if it's broke it
looks like it might be broken
yeah that's sucking the first rope says
don't need some work - and that bulbs
probably been but the things cooperating
so we got all the lights doing what it's
supposed to do
that was my son
kind of get an idea how it's gonna play
what she's getting there so next up
we're gonna take this off and get the
displays behind it and the soundboard is
behind that so we're gonna mess with the
soundboard next because it's annoying me
so we're getting a little farther along
we had to stop for a little while
because I didn't have any of the
pinball's for it so I ordered a ton of
the pinball's I have no idea how many go
in here I saw a guy online trying to
sell one and he mentioned that he had
just bought a t10 balls for it so I
bought a t10 balls for it
they're 5/8 inch and you can get them
from all the usual pinball places but
they're also the same as ball bearings
so if you can find some 5/8 inch ball
bearings they will work too I believe
now I haven't got it to work yet but a
5/8 inch ball bearing is the same as a
5/8 jump pin ball so I'm having a
problem where I cannot get the button
the game to start so the start button I
thought that the diode was bad so I
replaced the diode that didn't fix it
I've got this wire disconnected now
because I was trying some other stuff
but then I finally tracked it down to in
the back box whenever you fix corrosion
on MP use a lot of times the connectors
themselves have corrosion too so this
connector here one of the pins in it or
at least one of the pins in it isn't
making good connections so I'm going to
replace this connector and I think that
we'll get to where our Start button
works and will be up and running so
we'll see if that gets us anywhere so I
replaced the wiring connector on there
already and I replaced this connector
over here
I also replaced the connector over here
and I was able to get the start button
to work and the game is actually kind of
doing its thing now but there's no sound
yet so I've taken the display off and
then this board with the three displays
in it unscrews and we are back to the
sound board so I've been wanting to mess
with that but we finally dug it out so
there it is that is a Bali squawk and
talk you can see it down there on the
corner squawk and talk sound board so
we're going to pull that out we're gonna
clean all the chips
replace the capacitors and then put her
back in there and see if we can get it
to squawk or talk but I think it looks
like it's just held in with the same
quarter-inch screws that the other stuff
is so I'll pop it out so here is the
squawk and talk yes it really is content
and I've never played this game so I
don't know for sure but I'm thinking
maybe it doesn't even have speech good
it looks like this is just a the
squawking talked board which is
basically it makes the sounds and then
also makes speech but I'm thinking that
the speech is like these unpopulated
area up here I think I don't know this
little chip here kind of it's an 85 68
which i think is an analog to digital
converter or something I believe I may
be completely wrong about that but the
interesting thing about these sound
boards is you know that if you you saw
us messing with the domain MPU board
whenever they designed that mpu board
that was for the original Bally solid
state system which was like 77 and they
hadn't they hadn't even thought of sound
boards like this yet this one I don't
know if it's got a date on it but this
probably you know is more like 1982 so
it's a 1982 design so they to make it
expandable like that what they did was
they just made the sound board a
completely different computer so the
sound board can actually work without
the CPU the the mpu board in the game
working so it's basically it's a
standalone board so this is the CPU tube
it's a 60 808 this is the PIH of the
peripheral interface adapter it's a 68
21 chip and this is the RAM chip which
is a 6810 chip and then here's the ROM
chip so you know you've got these four
chips that can actually run its own
computer and so if you've if your MP you
isn't even in the game you can test this
board by pressing this button and it
does a little test sequence
I don't know specifically what the code
tells it to do whenever you press that
button but usually you enter you press
it on most of the boards with a set with
a sound separate soundboard like this
it'll play a series of sounds and stuff
so you can tell that it's up and running
and the actual NPU board that's in it
has a similar set up I don't think it
has a 60 808 I think it's a 6800 I might
be wrong about that but the PIAA is that
it uses our 68 21s and the RAM that it
uses is a 68 10 just like this so it's
kind of the same setup as the the main
board that runs the pinball machine but
if you saw I'll give your MP use not in
the this is the pinball machine so the
pinball is not actually up and running
your sound board probably won't make any
sound because the way it works is the MP
you sends signals over to the board and
triggers certain sounds and tells it to
do this and blah blah blah but you can
test it with that test button like we
were talking about so pretty cool now
whenever I took this out I took the
chips off and they were filthy
completely filthy so I think that was
probably the reason that the sound
wasn't working right and was cutting in
and out and by now it had already been
completely stopped now it's not making
any sound these caps could need
replacing but I think what I'm going to
do first is I'm just gonna put it back
in after cleaning the chips because the
chips were so filthy there's no way it
would have worked right so I cleaned
them all got them nice and shiny and
just the ones in the sockets you know
the ones that are actually soldered to
the board you don't have to clean
because they're they have a good
connection that's soldered but the ones
that are in sockets get all oxidized and
messed up so but they're nice and shiny
now and the sockets looked good so I'm
gonna put it back in the Machine and
we'll see if we get any kind of sound
and I'm also gonna start it up to see if
we get any kind of gameplay going for it
and then you can tell me what you think
well that did not get it going again so
I had to look a little more deeply into
it here's the scoop so when you first
turn on the game I went and checked out
the flash code so this is the little LED
and one a squall can talk the ROM the
code in the ROM tells the flash to do
certain things when it comes on so it
flashes on this particular board four
times and so one of the flashes it
checks the RAM and one of the flashes it
checks the PIAA and all this stuff right
and so on a rapid fire if it flashes
four times that means it's working fine
on most other games if it flashes five
times that means it's working find the
fifth flash as it checks this chip and
this chip isn't in there it's like a
sound generator that's used in the
speech I think that the actual speech
chip goes up here or something
so I'm pretty positive that these don't
have speech but anyway it's supposed to
flash four times and it does flash four
times and if you watched earlier in the
video or the previous video this thing
whenever we first started working on it
was actually making some sounds you
could hear some stuff going on in below
blah and then that stopped so I think
all of the actual computer part of it is
doing its thing but I don't hear a peep
out of it so next thing is we replaced
all of these little capacitors and the
whole board was covered with these
little tiny axial 1uf 50 volt capacitors
those things are known for going bad
I've had a a mr. and mrs. pacman I think
has this board or I believe that's right
that I had a problem before where one of
the little 1uf ones was messed up so we
went ahead and replaced all of the
capacitors except for the big filter cap
capacitor because I just didn't happen
to have that one and then the last thing
that we're gonna check I figured I'd
show you is on the board there are two
little potentiometers it says sound
volume and speech volume
so on this particular game on rapid-fire
those are used to mix well on the squawk
and talk those are used to mix the sound
volume and the speech volume so it's how
loud the voices right well in this game
I don't think there's even speech so I
don't think this one matters but
sometimes what happens is this Vaught
one of these pots will get messed up
they're kind of cheap that wasn't the
best the best product to put on the
board so we're gonna test to make sure
those are all right and then on
rapid-fire actually in the software you
can turn the volume up and down so I
went and checked that and I had it set
on 8 so it's turned up it goes from 0 to
15 so it's turned up halfway but I need
to check this pot to make sure that it's
working right so a pot if you don't know
if you're you know just starting out
with this kind of stuff a pot pot is a
potentiometer so basically what it is is
it's a resistor that's variable and it
says right on the pot what size it is so
this particular one then both of them
say 1k ohm so it's in a foul it's a
thousand own if it's all the way one way
so we'll turn it over and this one here
is the one that we're interested in so
what I'm gonna do is I'm gonna take a
multimeter which is set on resistance
right and I'm gonna try to do this with
one hand if I can but we're gonna see if
it's a 1 ohm plot like it says it is if
I do this with one hand
maybe check it out I did it was on him
so the pot all the way across the two
leads is 1056 ohms so that's about right
that's how it's supposed to be and then
on the other one let's see if it's
something similar the other one is a
thousand and ninety two M's so what that
means is that's the amount of resistance
all the way across the horseshoe with
the pot now whenever you turn the knob
it drags a little thing across the pot
and makes us short so it allows you to
adjust how big of a resistor you are so
you can see how that works real good in
volume so if you just had those two
shorted across each other it would be a
full volume all the time and so whenever
you turn that thing down
basically it's adding resistance to the
volume line or however they've got it
designed you know they might have a
design actually they complete back the
other way but so now what we're gonna do
is we want to check between the middle
leg man that's hard to do with one hand
with the middle leg and the outside leg
oh and we're getting two thousand two
hundred and eighty ohms
now should that be possible it's it's
only in a thousand ohm pot so between
the middle leg and the outside leg you
should have less than a thousand ohms
right check this other one so go on the
other way it's got three point three
thousand ohms resistance between those
two so in other words that pot is all
screwed up right it's not right let's
check the other one
I'll rheic splain it here in a second
just in case you're the beginnings with
this if you're into this stuff all the
time I'm sure you know exactly what I'm
talking about
ridiculous trying this with one hand but
okay you got the message okay so a pot
it's a knob and from one leg to the
other leg is the maximum amount of
resistance well these are 1k pots that
there should be 1000 ohms resistance
between this side and this side maximum
right and that's kind of what we got we
got a little over two adders like one
1056 ohms but that's probably within
manufacturing space so between the
outside leg and the middle leg should
never be more than that because the
purpose of it is whenever you turn it
you lower the resistance so if you're
all the way up it's at a thousand ohms
resistance if you're all the way down
it's at zero ohms resistance so you
should always be somewhere in between
there well with the pot what happens is
the pots get dirty and so they get dirt
and grime and grunge in there and so
that little metal piece that touches on
the track of carbon or whatever it's
made out of it doesn't connect right so
the resistance between the middle leg
and one of the outside legs is now over
a thousand so it's worse than if you
have the thing turned all the way down
if you had it turned all the way down
the volume all the way down you'd have a
thousand ohms resistance but I just
measured two thousand two hundred ohms
resistance so that pots all screwed up
so I need to replace that so I'm going
to find a 1k pot and swap that out and
then hopefully that'll get us our sound
back all right so we put it back in and
I have since discovered that since this
board doesn't use everything that the
full squawkin talk does it doesn't have
speech or whatever when you press this
button nothing happens usually when you
press that it'll reset it'll play the
sound and it'll reset the board and
you'll get the flash codes and stuff
again but on rapid-fire it does not do
that so what I'm going to do is I'm
gonna turn the game off and then back on
and you can see you can watch the LED do
it's for little blinks and then it's
going to play some music for us or some
sound effects force one two three four
okay now the game still hooting up
[Music]
alright and if you go into of course if
you play the game it'll play music but
if you go into the test mode if you go
up the setting 20 you can adjust the
volume so if you go to setting 20 you
can adjust it from 0 to 15 you can also
use that volume knob that we replaced
but your problem that you have with that
is it's not really designed for that
it's just it's more designed to mix that
and the speech so even though there's no
speech so I hope my points getting
across they basically just use the board
that they used on a bunch of other
pinball machines put it in this but it
never made the speech part world
alright ok so the game is actually
working what I'll do is I'll put the
board back in I'll lean the displays
back up and just for a minute we'll
screw around with it alright so we've
kind of got the game up and running but
it's obviously it needs tons of cosmetic
work still and we've got a few of the
lights that are still acting up that we
need to replace or we don't need to
replace it we need to get them working
properly you can hear random balls
rolling around inside of it as they're
dislodged we bought one of these things
so I'll point it up and just kind of
give you the gist of show you that the
thing is up and running and then what
I'm going to do is we're gonna do all
the cosmetic stuff to it that we need to
try to get it looking as good as
possible get it all together how it
should be presentable and then I'll film
a full video of it where I review it and
we play it with the tripod and
everything so you can see what it was
like and again you gotta remember this
is not a pinball machine it's a sucker
shooting game it just looks like a
pinball machine
so I'll start it and you can kind of see
the deal the gun by the way will turn
when you turn the handles and there are
triggers on each handle this little
white thing here is like a shield so if
you hit this button you move that shield
so you can move that around to the left
or to the right to block things so the
guys are advancing
so you rapidly fire at them
so you kind of get the gist of how this
thing played back in the day and it
really does shoot pretty fast so we
still got a lot of work we got to do on
it but we kind of wanted to just film a
video showing you kind of how the
internals work on one of these a little
bit and what you have to go through to
fix it but we've got it back up and
running and we'll we'll get on the
cosmetic stuff and hopefully we'll have
a video up soon of the completed the
completed project so if you liked what
you saw or if you have any comments
about it or any questions about it leave
them down below give us a thumbs up for
taking the trouble to film this while we
work through it a little bit we've never
worked on one of these so we thought
it's kind of cool and we don't document
it a little bit give us a thumbs up
leave your comments below make sure to
subscribe to us and every time we do a
video like this it'll let you know that
there's a new cool video from Joe's
video games up and we will see you on
the next one rapid fire