Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
cool pinball repair video for you today
we have been working on this williams
pat hand pinball from 1975.
if you have not seen our videos that
we've done so far on it go check them
out
we did one where we showed the condition
it was in wow look how fainted faded the
pink is
holy moly i just noticed that we did one
where we showed the condition that the
cabinet was in
and we worked through all of this stuff
in the back in the in the bottom
we found a couple little issues and uh
we showed how to how to adjust relays
and then we did another video where we
worked on the back box
and we did all this stuff in the back
here in the back box
and we showed how to rebuild a stepper
unit and we showed how to rebuild a
score
uh a motor a score wheel i mean
it's not a score that's score motor what
do they call those score wheels i guess
drum units that's what they call them a
drum unit
and that's as far as we got so far so
today
we're going to put the play field back
in this baby look at it
it's sitting over there out of the way
being polite it's waiting its turn
well we've done the the the coffin
i'm starting to call the bottom cabinet
the coffin we've done the coffin we've
done the back box now we're going to do
the play field so
uh first thing i'm going to do is pick
that heavy sucker up and pop it back in
the cabinet where we can get it up
off the ground where we can work on it a
little bit
it's not real heavy i think they're
about 40 pounds but it just depends on
how much stuff is
hanging off the bottom of it how much
jewelry it has
so let's throw it up in here and take a
look at it
okay so there it is and people ask us
well how do you know where to start
it looks a lot more confusing than it is
once you mess with them a little bit you
kind of figure it out
so look i took the wires off and now
it's even less confusing
so two of these go down to the bottom
these are jones plugs and it's how the
bottom board connects to the play field
this other one
that's loomed separately whoa
it's like that because it actually goes
up in the back box
and so we got to clean these jones plugs
see that corrosion
what is that is that oxidization i don't
know
but let me show you something let me
show you something
okay so you see how that looks now look
at the other side
unknown collar see how it's not quite as
bad on this side
i'll show you why after i see who the
unknown caller is
there's a telemarketer
but the reason it's worse on this side
is because when it's mounted in the back
box that's the
upside so that's actually a lot of
that's just dust
well whatever but the bottom is not
quite as bad
because it's down and the other ones
they mount like this
so the top gets filthy
but the pins aren't quite as bad they
don't get as bad as that one that's
facing
up but you still need to clean them all
so the way we clean them is we just use
really light
sandpaper and just get the grime off of
it other people have other ways of doing
it
do your favorite way people don't listen
to how i say to do it
do it the way that you think is best
okay i've been working and working and
working
now some people have mentioned that you
don't really want to get the tin off of
it so i try not to go too far but
some of the tin is off of it people deal
with
it it'll be all right
so we got it nice and shiny everything's
cool
all of the crap is off of it now the
actual female part of the socket you can
do the same thing
if you have like a you can get a gun
brush actually
that you that you use to clean the
barrel of a gun you can get them at just
the right size or it'll go
down in there i can't remember the size
though i would tell you but then you'd
go by the exact size that i said and it
would be wrong if i just guess at it so
but there is a if you get an assorted
kit you ought to be able to do it
it's that size right there okay
i would say
barely bigger than a bb so i don't know
what kind of gun would be that small but
a little teeny tiny bullet that's
smaller than a 22 or a 25 shell for
for show and now this video will get
demonetized because i'm saying the g
word too much you get my point that's
it's about the size of
if you take an ink pen and take
the uh the cartridge out of the inside
of it it's about
about the size of that okay
so we got those we'll plug them in i'll
have to turn it off first we actually
have it on
because i like how the lights blink
all right so if you're you should be
following along at home if you're trying
to fix one of your own you know i'm
telling you how to do it people we're
trying to save
all of the pinball machines so if you've
got one that's broke
all you have to do is watch these videos
and yours will get working too
so if you're following along at home
this is the next thing we're doing
we're going to plug those in and then uh
with the game off i'm going to replace
all of the light bulbs
so i'm going to throw all of them away
now people have asked me why do you
replace all of them well because we sell
them so it's like a reliability thing
you know the bulb that's in it's
probably 30 years old
they might keep working or some of them
might die so we're going to put brand
new ones in them
just so that we don't have to worry
about it now
if it's yours at the house you might not
care if all the bulbs are new i mean it
doesn't really make them burn any
brighter or anything
so if you don't mind replacing them when
they burn out
go ahead just replace the few that are
burned out
but we're going to replace all of them
you can also put leds in yours if you
want if you want
people ask us about leds all the time
because they run
cooler and all that that's true
everything people say about leds
is true i just don't like them because
they don't look original
i just like the original look that's
just my personal preference
but if you want to put leds in yours go
right on ahead
and if i ever get it i'll pull them out
and throw them in the damn trash
but uh it's not a it's not an
irreversible mod or anything like that
i don't really like modding them at all
if i can help it so if it was up to me i
would have them pretty much how they
were originally
i do a couple little things that are
different than how they were originally
but not much
we get that too with people where they
want us to put dc flippers
on them so the a lot of the original ems
had
ac powered flippers that are weaker than
if they're dc powered flippers i don't
even know why that is
i guess maybe since the ac you lose half
of the wave or something i don't know
i'm sure i'm sure you engineers know
better than i do but the dc ones are
stronger
this is a 1975 williams and if you look
that's a bridge rectifier it does
actually have dc powered flippers in it
they made some of the later ems have dc
powered flippers
this thing the flippers are probably
strong as well we're probably still
going to
replace the plungers but i'll bet these
things will freaking slap
and that's what you want okay so i'm
going to plug those back in i'm just
going to go through i'm going to replace
all of the light bulbs
and as i do that you kind of examine
each socket as you're going just to see
if any of them look like they have a
problem
sometimes they're loose and so what i'll
do nothing's plugged in right now by the
way
what i'll do is i'll spin them a little
bit so if you spin them and they're real
loose
you might need a new socket but usually
you can spin them and they kind of get
to a spot where they
there's a little more resistance what
that means is in that spot
you've got a really good connection
between this pressed on base and this
metal bracket that it's on
that's how it gets its its power so one
of the wires
is soldered to the bracket you can see
it there
and it comes up and this is just press
fitted on so over time they get a little
loose sometimes
if you spin them though it gets it to a
nice a place where it makes a better
connection
and i just do that with it off you know
and then this
line over here is the other one you need
to make sure it's not
shorted out where it's touching the
bracket because then you're shorting
both your lines together and it'll blow
the fuse
[Music]
you can also you can see how it kind of
oxidizes the
surface of the bulb see how nasty that
looks
so you can also take a small brush and
kind of clean the pen in there a little
bit
but usually you don't need to do that if
you get one that's acting up though
that's what it needs
if you get one that that's all loose and
it's just wobbling and stuff you need to
replace the socket but it's kind of a
pain because you have to solder it on
usually you don't have to do too many of
those though all of these look pretty
good so
unless i find one that's damaged or
something i can probably get away with
the original ones
so i'll do the light bulbs and uh we'll
see how that looks
and then move on to the next thing
okay i'm pulling light bulbs whenever
you do these you will find that the uh
there will be all kinds of soot from the
bulb inside
all of the inserts some of them will be
worse than others it kind of depends on
how much the bulb was on
um and so you need to clean that out or
you'll see it
whenever the bulb lights up you'll see
this ring on the play field
so the easiest way to do is just use
like windex and a q-tip or something
like that i don't have any q-tips here
so i'm using like
a little tool with a paper towel on it
you just
want to clean them the bottom of the
inserts
get it all nice and shiny so that
whenever the light comes through
it'll look nice and clean
much better
look at this
somebody has written
20 and 40 and 15 equals 75
plus 2 dollars and 40 cents equals 77
40. now that is a mystery folks
figure out for me why that is on there
20 40 and 15 equals 75 plus 240 equals
77
40. what is the point of all that
i can't figure it out
so i got all the light bulbs replaced so
next thing is we're going to do all the
switches and then we're going to turn it
on
uh we've got so you've got all the
playfield rollover switches
you need to check all of them to see if
it's physically doing what it should so
when it rolls over to switch
it pushes a little leaf switch together
some of them are double stacked like
that just make sure both of them are
moving
and you want to do it just like you did
the relays
on everything else when the long blade
moves when it touches the short blade
it should move the short blade a little
bit if it moves it a little bit
everything is great so i'll do all those
and i'm going to
clean all of these switches on these
relays so these relays are for like all
of the
um like the features of the game so
number one joker relay two three four
setup relay double bonus relay special
relay
ace relay king relay queen relay jack
relay 10 relay
sounds like it's going to be really fun
and then
we finally found
our 100 point relay and our 10 point
relay that i kept saying was in the back
box but they're not
and this is something to ace reset relay
and this is the advanced relay and the
bonus relay so i thought the reset relay
was under here but i guess not
um and then we have this bonus unit
and then we've got one two three four
five six coils to mess with
so i'm going to start cleaning switches
you can use anything to clean them
we use like a really worn out file you
don't want to use anything super
abrasive that's going to cut away the
contact
that would not be good but you can the
the trick that
the old school repair guys used to say
was to use a piece of a business card
because you're just trying to get the
dirt off of the the contacts
but you know they were doing it on
machines that weren't all that old yet
so we use something a little a little
stiffer
so i'm going to clean through all of the
switches
and then we can plug it in and see if
the lights come on i can do it now but i
want to clean the switches first so that
i can trip some of these relays and see
if it turns on the associated play field
lights
all right so cleaned all the switches we
haven't
done the bonus unit yet but it looks
pretty good so far
ah it's not that bad right and we
haven't done anything with the flippers
but they'll probably work how they are
for now so but we're ready to turn it on
so let's turn it on and see if any of
the light bulbs work
and we're finally to the point well
maybe we should rebuild the bonus unit
first but we're about to the point where
we can actually start the game and see
if anything works
okay so we have some lights on
what am i hearing
something's buzzing
oh it's the bonus unit
hmm not good people that should not be
held in like that let me turn it off
[Music]
so the bonus unit is stuck in
which one would that be that would be
it's the step up coil the bonus unit
step up
coil is stuck in so how do we figure out
why it's doing that
well we look on the schematics okay
so here's how you track stuff like this
down
so the bonus step up coil is always on
so if you look so we're following this
double line down there are two ways it
gets power
one way is down here through the
advanced relay i looked at that
the advanced relay these two switches on
the advanced relay were not connected
together
and the advanced relay was not on
okay so the other way that it gets power
coming down is through this
it says bonus unit zero position
so basically the the bonus unit resets
back to zero but you start the game
i guess with a thousand points on the
bonus or a thousand on the bonus or
whatever it is i haven't even looked at
it yet but it's a thousand probably
you start the game with a thousand
points so it resets it back to zero
and then when it gets to zero
those two lines are shorted together and
they're in
a series with a switch on the motor
switch 6a switch or
cam 6 on the on the
switch c so if you go down here we're
back over to the score motor
there's this cam of six
switch a says pulses bonus
step up a
okay so then i started thinking i didn't
hear the score motor turn around
so if this if this uh switch
is stuck on the high part of the cam the
switch will be closed the whole time
it needs to turn around until it falls
down into that valley on the cam
so i didn't hear the score motor uh turn
or anything did you
hmm did you hear the score motor turn
okay so i've still got the game on
the score motor is not doing anything
so uh usually if you turn it a little
bit
by turning it out of one of these
valleys these uh
valleys i don't know which one but on
one of them whenever you turn it
it makes that switch connect see the
grease all over my hand it makes that
switch connect and it holds the motor on
itself
so it will never move just a little bit
if you turn it a little bit it makes
a switch connect and it turns around
until it gets to the next valley and
stops again
because when it gets to that valley that
switch opens okay so this thing is dead
so here's the motor over here is a
service
connection so you can pull this pin
out and put it over here so that it's
turned off
service jack on and off but look
the wires broke off of it so that wire
goes back and it just goes to the motor
so i need to resolder that wire
on that jack there where it broke off
and that'll get our service motor
turning again i was able to get the coil
not to pull in
by just moving the spider up off of the
first uh
rivet but watch what happens when i get
back down to the first rivet
well i must have moved the cam enough
that it doesn't do it there we go
see it's locked on it's trying to pull
it in and move it forward
but it it when the when it pulls it in
let me move it off of it you see how
when i moved it off it made it actually
move
when when the trying to explain all this
stuff when i think of it
in case it'll help you with something
it's not this coil moving in that moves
the gear
see watch the stuff there okay so i'm
all the way in so
if i stay like this the gear will never
move
because it's letting go of it that that
moves the gear
so if you get something locked on a lot
of times it'll just be sticking where it
is and you
it makes it harder to even tell what's
locking on
but it's all working fine my whole
problem is
i just need to get that wire back on it
so that the score motor turns around to
its home position
okay got our wire soldered back on there
let's try it out
voila
that's stuck on coil
we got our general illumination on the
playfield up and running
we got our five ones in the middle lit
up
none of these are lit up though
and none of those so let's see if uh
if i hit these relays let's see if it
makes other stuff light up
what you think
what what was that one yeah there we go
so it's turning these off
trying to not get my hand uh
broke by the
that's a pretty hefty coil there people
if it decides to reset
it might reset me
alright so those do those but they
didn't light up the other ones
let's see what this does
well that load up that is the special
relay
oh and the couple
the bulb there damn i don't think i
changed that bulb all right so it lit up
both of those
let's see what this wants to do
it's the double bonus relay okay how's
that one
working right through it people
that was the number four joker relay oh
no that was the
setup relay
it's a trap that's the number four joker
relay
or
i don't know i'm just hitting relays
people got all four of those lights back
there all the ones on the bottom
now remember we haven't done anything on
the top of the playfield yet
i wonder what makes these come on hmm
must be one of these
let's try it shall we
i don't do nothing oh that's the that's
the 100 and the 10 point relay
i don't know
there we go
huh okay so all of our lights appear to
be working people
what do you think about that the ones in
the middle i guess turn themselves off
because of these relays
but if this were to do this
all right all right all right
and then our bonus would be this bonus
wheel we haven't rebuilt the bonus yet
so see how the light is kind of iffy
that's because i haven't cleaned these
rivets yet
when i clean those that will make it
less iffy
three two and when i get to one
i know one will be fine but when i go
past one it should step it back up
oh no it won't without the score motor
turning
so that's the home position
one two three four five
six seven eight nine ten
all right yeah so that definitely needs
cleaned up a little bit but
i think we got all of our lights working
and
uh i cleaned all the switches so we're
going to work on this bonus
unit to get that more reliable then
we're going to work on the flippers and
we'll be done with the underside of the
playfield
so we're going to rebuild the stepper
unit to make sure all those lights light
like they should now
it's worth noting too that you know it's
not just the the lights
the stepper unit doesn't just make the
lights move it also is used whenever the
machine is counting down your bonus so
at the end
of the ball it counts back and uses some
of these rivets
in sequence with the scoring
relays to give you the actual scores so
if this isn't clean you also won't score
it won't just be that the lights don't
work
so i've removed the uh little uh
spider off of it and what i always do is
i just lay it down
exactly how i removed it off make it
real easy for me to pop it back on there
and i'm going to clean these rivets just
like we did in some of the other videos
you've seen us do we're going to
sand these slightly with very mild
sandpaper you don't want to go crazy on
it
because you don't actually want to take
any of the
um the brass i guess that's brass
the brass you don't want to take any of
the surface of the rivet
off if you i've seen them before where
it's almost always all worn away
which is bad if you look you can
actually see that they
protrude above the bakelite board and
you can see the little hole next to it
is actually a lot smaller so the rivets
are
are much larger than the actual holes
they go through
so we're going to just sand it just to
scuff it up and get it nice and shiny
again
and that usually gets it where it makes
good electrical
contact whenever the the disc is
touching it
so as you saw in the earlier video the
uh uh the thing was already working it
just
it wasn't making good connection on the
rivet so i put a little bit of oil on
the shaft because it's a it was a
metal shaft going through a metal
bearing if it's metal on metal you
definitely want to use a little bit of
oil
and then on the actual bake
light board bakelite bake a light board
i always use this stuff
so you might want to buy you some of
that if you do use our amazon link
um and uh thank you by the way to
everybody that's been using our amazon
links that's pretty cool
we appreciate it the ones from
international are starting to work too
i've noticed that there's a bunch of
stuff
somebody just bought something in canada
like it was a
some kind of huge vacuum set or
something and we get a little commission
because he clicked our link before he
bought it so we appreciate that up there
in canada whoever did that so thank you
to everybody that's been doing that
but uh anyway back to our regularly
scheduled program
so we put a little bit of it on there
you see you don't want to go crazy with
it it just helps it uh rotate around now
you don't want to use just anything on
this vaseline might not be a good idea
the reason that stuff works is because
it's dielectric
and uh somehow dielectric stuff
will insulate so that the two rivets
don't electrically connect to each other
that are next to each other and
but it also conducts so i don't know how
that works but
uh the rivets on the actual spider it
helps them conduct and then it also
keeps it from
if you put just a regular oil on it
it'll actually short out the ones next
to each other because it will
conduct don't ask me folks i don't know
why it does that but
all i know is that super lube stuff is
fantastic on these this is what i use
okay so we are at the home position and
when it gets to the home position
it should open up that little switch so
let's come off of it one
and now it's closed
so that's how you want it just perfect
perfect okay so uh
one other thing to mention there is this
one wire here
i guess those were originally white
wires
and they have taped them to this other
wire that is fastened down here on this
screw
and so i've done extensive research
and it looks like originally those two
wires had a little eyelet
which may or may not still be in there
and it was attached to that screw
it attaches to the ground which is
basically the or not maybe not the
ground but it attaches to the
the metal of the bonus unit
which attaches to
some of the fingers on the spider
and so um it's supposed to be like that
on that other screw i believe
but it looks like at some point
uh it stopped making good contact the
the two brackets there weren't connected
to the metal
as well as i should because that hole is
a little wallowed out
there's a word you haven't heard in a
while wallowed
so what they did was they attached the
wire and they ran it down and connected
it to the other foot
the other bracket so that it would make
better contact and
it's working they did a pretty good job
i know a lot of people don't like
electrical tape but
you know hell if you're wrapping up
something big like that electrical
tape's the way to do it
it's working i'm gonna leave it like
that okay so let's see if we're any
better on our lights
one position two position three
four five six seven
eight nine ten
and it turned on all these too
well we got a lot of lights on right now
people
now watch what happens whenever you hit
this one
oh if i can hit it it only goes back one
step
at a time so why is that why doesn't it
just reset back to the beginning
it's because it has to count it each
time so it goes back one step
score motor turns it makes the
relay fire off give you a thousand
points and it goes back one more step
score motor turns it makes the relay
fire and give you another thousand
that's how it uses the uh that unit to
actually give you the bonus instead of
just
displaying it on the light bulbs
okay so you know what we are up to the
flippers
let's mess with the flippas a little bit
what do you think oh by the way i should
mention
i screwed up earlier i said that these
have dc flippers they do not
they do not have dc flippers i looked on
the uh
schematics and they have dc pop bumpers
so the two pop bumpers and the kicker
here
there's only one because remember the
pop bumpers are down low are what is dc
the flippers are not dc they are the
old-school ac flippers so i was wrong
about all of that but we'll see how it
plays there in a little bit
okay so on the flippers what i'm going
to do is i'm going i don't even know if
i've got these links i think i might
this is a william so i probably do i'll
see if i've got new links
plungers here
usually
oh we're gonna get a good video out of
this one uh usually
you don't have to replace everything you
just have to replace some of it a lot of
people will replace the coils you don't
usually have to replace the coil
now since i said that i'll have to
replace all three of them but usually
you don't have to replace the coil you
have to replace the nylon sleeve in
between
that the plunger runs in and out of
usually you have to replace the plunger
if you look
see that wobble right there where it
where the link hits the plunger how it
can move a little bit
you don't want much play there that
there's kind of borderline it would
probably be all right
uh but often that's where your your uh
your wear is in the
in the flippers and you need to replace
that for sure sometimes you have to
replace the coil stop down under here
we'll look at it whenever we get it out
and then on this particular one
lookie here
the bushing is broke got to replace that
bushing
so if you need just parts you can get
those from
a lot of places but our favorite place
is the pinball resource we don't know
those guys they don't pay us to tell you
that but we
we uh we really like them they do they
kind of specialize in ems although they
do do
they do do solid state stuff too
but they're they're the the kings of
electromechanical pinball machine parts
they've got everything and they've had
stuff reproduced over the years
they also have the got lib license so
they have a lot of licensed parts
that they've made over the years but
anyway they sell just parts
so you can get just that bushing and
just that plunger
and just the nylon sleeve and just the
coil stop if you want or they sell the
whole freaking thing so that's
they'll sell you all this stuff if you
need to oh sometimes the end of stroke
switch needs to be replaced too
if it's badly pitted that one there it
looks like it's going to be all right
but check out the pinball research and
get all your parts there or you can just
get a flipper rebuild kit there too
they're usually not even that much money
thirty forty fifty dollars something
like that
but what do you do on one like this
where there's three flippers
huh i'd have to get a flipper rebuild
kit and a half
i bet they have a provision for that
that probably run into that problem all
the time they're pretty smart guys and
gals over there
okay so uh i'll take one of these
flippers apart and we'll start
swapping some of the parts on it
so here's the old coil stop we took off
sometimes if your plunger isn't hitting
the pis and hitting it
nice and square you'll get annoyed
you'll get a lot of buzzing and stuff
like that
and sometimes the end of it will get
mushroomed up around the edge there so
i've hit it with a file and cleaned it
up a little bit made it a little better
you can get a new one too like i said
use it for five dollars sometimes you'll
get these and this entire stud will
break off see how it's riveted in
that whole thing will be broken off and
inside the coil sleeve
so of course then you need to replace it
for sure
um and the old metal sleeve that was in
it i took out and replaced with a nylon
one the metal one was
stuck to the the uh coil stop that i was
just messing with
this plunger i'm going to show you again
the play in it
it's got a little bit of play i just
compared that to a brand new one though
and a brand new one has about half that
play
so i think we're going to see if these
are strong or not if they're strong
we're just going to leave them if
they're not strong we're going to
order new uh new plungers for it i've
got some but i don't have they're not
the right
ones for a williams i've got some valley
ones so the new ones have just a little
bit of play in them
um but we're on the borderline with if
that's too much play or not
um and then sometimes too you're the end
of your plunger there
we'll have the end of it mushroomed up
so that it doesn't
smoothly travel in your
coil by the way you should never oil
those if you put oil on that stuff
you're
kind of asking for a fire don't do that
don't put oil
on the plungers on any of this crap
people
okay so uh oh and the end of stroke
switch
you got to get that just right to where
it stays closed almost the whole time
and then opens right at the end
so that's probably pretty good
you want to open maybe
a little less than an eighth of an inch
something like that
so i'm going to uh replace the you know
check out all three of them replace the
sleeves check out the uh
check the plungers for wear and check
the
end of the plunger to see if they're
mushroomed out clean the end of stroke
switches
and then you know what time it will be
it'll be time to test it out and see if
it'll start up a game or something
so i replaced the sleeves and all three
of them worked on them and one thing i
noticed is
this bottom one the third flipper
it's had something done to it so
if you look it's out of line
see that screw holder
it was originally farther over that way
so they must have done that for some
reason somebody moved it at some point
and i'm sure they had a great reason for
it
but uh it's not quite lined up exactly
like it should be but
it'll still work the only thing that it
does is it makes this uh
paul be slightly i mean the link be
slightly different
um the flipper can still be rotated
where it's actually at the same angle on
the play field and all that
so for some reason though they took it
from that and then moved it slightly
i don't know i don't know why they would
do that but i'm going to leave it
because it might have been fixing some
problem maybe there was a hole in the
play field that was wallowed out or
something
didn't i already used the word wallowed
in this series of videos i think i did
okay so i've done everything i can think
of to do on the
cabinet i mean on the the coffin
i've done everything i can think of to
do in the back box and i've done
everything i can think of to do on the
bottom of the play field so the only
thing left to do is to see if it does
anything
and then we still got to do the top of
the play field we still got to
fix whatever's wrong with it whenever we
try to play it
and we've still got to do some cosmetic
stuff so i'll lay the play field down
and then we'll try to turn it on and see
if this thing will start
so we haven't done the play field yet
usually you wouldn't test these
uh with the old rubber rings on it
because of things like
this see how the ring is dried out and
it's made it where the
it's unplayable like this but it's made
it where the
switches don't touch right sometimes it
goes the other way it'll make it where a
switch is stuck or something
but on this particular game there's
hardly anything to hit that's not a
stand-up
switch there's hardly any rubber rings
just interesting um and we're not we're
not really going to play it
we're just going to see if it starts
yeah even back here
there's some rollovers but i messed with
them when i did the underside of the
playfield
um all right so let's turn it on and see
if it does anything
all right we already had the lights
so remember when i did the back box
score reels and i said to leave them all
off of zero
so that you can see if they reset
whenever you start the game so now we're
finally going to see if the score reels
work
so i'll try hitting start see if we get
anything
so everything reset back to zero it says
we're tilted so that might not be good
we're on ball one
and it kicked the ball out but we're
probably tilted
yeah we're tilted also it says ball and
play number two so that's not right
either
so let's see if the ball will hang
itself
up
we also don't have flipper rubbers on it
so we're not going to actually play it
it moved to ball three but we're still
tilted
that buzzing noise who knows what that
is
it may be the uh maybe the
remember i think this is supposed to go
to one or something
all four
ball five didn't light up i haven't done
the lights in the back box yet we're
still tilted
let me see if i can figure out what's
making the buzzing noise
[Music]
what are we hearing
what's so loud down here
oh it's the tilt relay
okay so the noise that we are hearing is
the tilt relay
why is the tilt relay on it's because
yesterday i was showing somebody how the
tilt works
and i adjusted the damn tilt bob all the
way up
loosen that back down
so let's try this again okay so i
adjusted the tilt relay back
that got the buzzing stop i mean i
adjusted the tilt switch
looks like it's trying to score a little
bit
we definitely got some issues that was
it counting down the
bonus it looks like
we got a thousand points
it says ball three
a thousand points okay so we're getting
there people
so we finally got the bottom of the play
field done we got the inside of the
cabinet done we got the back glass the
back box done
so next we need to clean the play field
so yet another video
of cleaning the play field and i've got
a special surprise coming
for these for this horrible wear here if
you didn't see the other videos
this play field someone has put mylar
over the wear and it looks
god awful and i can't take the mylar off
because the condition of the play field
is not good enough to really let you
take it off
i've never successfully done that you
can do it with heat you can do it with
cold but
every time i do it it rips all the paint
off the play field so i'm not even going
to try it this time
but i got to make it look better so i
got something special coming for that
and then we have some some paint work up
here to do and i will be doing that so
that will be on our next video so
hope you enjoyed it so far we're getting
there on it give us a thumbs up for
taking the trouble to film it
we're limping it along we'll have it
playable here pretty soon
i guess we're oh i didn't try the
flippers let me see if the flipper works
flip flip flip flip boy they look strong
don't they
so hopefully you enjoyed it i think
we're getting to the point where it's
limping along now
um so in the next video we'll do the
play field and we'll do a video where we
troubleshoot all of the
scoring and the play field and see if
everything works and
work through the schematics if something
doesn't work but give us a thumbs up for
filming it make sure to check out our
brother's channel my brother donny i'm
over there with him all the time doing
cool stuff
it has nothing to do with arcade games
though so it's usually
working on vehicles or uh houses or
buildings and
crazy things that he gets into he has a
very adventurous life
my brother donnie go check that out and
by the way
thank you to the hundreds of people that
have subscribed to him
um everybody's over there if you're not
over there i guess you're just not cool
enough
but we're having a good time over on his
channel too and then also thank you to
everybody that has been using our amazon
links a lot of people have been doing
that lately and we really appreciate it
if you click our link below to amazon
and your country
amazon gives us a royalty for anything
you decide to buy on amazon
doesn't have to be something that we
sent you there what we tried to do was
send everybody to a uh
a link of their country's flag we
thought that was kind of cool
um so uh but you can go on there and buy
anything and it gives us a little
royalty
since we sent you there we appreciate
everybody that's been doing that it's
been picking up lately actually so thank
you
i guess more and more people have been
doing it thank you thank you
all around the world i think we just
signed up for australia but i don't know
if it works yet but you can try it
but thank you to everybody that's been
doing that and leave your comments below
let us know what you think so far and
let me know what you think should i
leave these flash bulbs in the back
glass i'm kind of thinking i might
what do you think you know i'm not a
modder i usually don't do that
but somebody went through a lot of
trouble to do that and it looks kind of
cute
it looks kind of cool i might leave it
so leave your comments let us know what
you think and i will see you on the next
video