Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
cool pinball repair video for you this
evening
we have been working on this bali xenon
masterpiece of a pinball machine here
for our buddy
frank and in the last video we worked on
the lights a little bit
we worked on one of the eject holes a
little bit and then we figured out
we figured out
that it's got uh some sound issues
obviously and it has some switch issues
so that's what we're going to be working
on today if you've got a xenon and
you've got switch issue issues
can't talk today what's up with that and
you've got switch issues too many s's
uh then this may be for you
and then also we need to get the sound
sounding better
all right so the switch is the thing is
whenever you play the game whenever you
hit the flippers
it does random scoring
so usually when that happens you've got
a problem with a vibration thing where
there's a switch that's really close
and when you hit the flipper it's a
violent thing and it goes
and it shakes the switch a little bit
somewhere on the play field it makes it
makes it uh close
so it could be that but it looked like
at the end of the video we were figuring
out that there was something going on uh
possibly
with the uh the switch matrix or
something so i don't know
so we're going to go check that out
though so let's go into test mode and
put it in switch test so if you if you
open up a belly on the coin door there
is a test button
you hit it one time and it will do
all of the lights
okay
i believe we still got all them working
so that's good
yeah looks like they're all working
okay and then you hit it again
and it will do a display test
now you'll notice that it's also making
some of the lamps blink that's because
there is an auxiliary lamp board in
xenon
and
it has something to do with the lines
that they run the displays with so it
it'll do stuff like that that doesn't
mean anything's wrong
they also have leds in this particular
machine
so that sometimes will make things do
weird stuff too
that's fine it's not hurting anything
next one is the coil test
might get some sounds here too
nope no sounds on the quarter crystal
this one
okay
now i don't know
i think that may be a sound test
there we go
and so that believe this is a switch
test it's saying number three oh three
so i don't know what 03 would be let's
try hitting a different one to see if we
get anything
we're just getting a 3. let me look in
the let me look in the manual if you
have a problem you run into always a
good idea to read the manual so let's
make sure that i'm on the right uh
test and what it what
03 means
all right you hear it in the background
still complaining
game self-diagnostic tests pressing the
self-test button inside the door
initiates the self-test routine
pressing the self-test uh
all switch layups flash off and on
continuously pressing the self test
button again causes each display on each
display each digital in each display to
cycle from zero through nine and repeat
continuously
pressing the self test button again
causes each solenoid to be energized one
at a time so we did that pressing
self-test button again causes the sound
module to play the game over
tune repeatedly
so it was playing something i don't know
if it's a game over tune but we haven't
we're not doing sound yet we got to do
switches first
pressing the self test button again
causes the mpu to search each switch
assembly
for stuck contacts if any are found
the number of the first set encountered
is flashed on the player score displays
so we're getting a zero three flashing
so that's the the first stuck switch
that it is found the number remains
until the fault is cleared uh-huh
so whenever i pressed another one
it wouldn't tell me the other one
because it's still going to say 03 as
long as that stuck see page 17
for help in stuck switch identification
other numbers may follow if more stuck
contacts are present
if there are no stuck switches
the match ball and play display flashes
zero okay
so we need to go to page 17.
here we go
we're going down
all right
here we are folks we have found the
switch assembly
number three is the upper side target
okay it must be stuck let's go see if
it's stuck
[Music]
so here is the upper side target and
it's hard to see
but wouldn't you know it
went too far folks we went too far we
got to go back out
look at that auto focusing fighting for
it
boom it's stuck
[Music]
should have known
all right let me see if i spread that
apart a little bit uh with a little
screwdriver or this little file
okay so i spread it apart now it's on 21
if i hit the switch again
i get my three back
so that tells you that it's fixed right
so now we need to go find number 21.
okay so number 21 is the number four
drop target as you can see all the drop
targets are down this game has memory
drop targets so uh the the game itself
can drop the drop targets
individually so whenever we did the
solenoid test it was going through and
doing all of that
and so it has dropped all of them at the
beginning of the game it pops them back
up though so uh i'm gonna reach in and
reset all of those and let's see if that
clears up number 21 for us
because
i mean it should be telling us 21 stuck
the drop target's actually down
okay so putting those back up
has cleared us up and now we just have a
zero
all right but i'm going to go through
and test all of them
just to see if all of them are working
too
number four
30
29
36
[Music]
got some stuff
it about bit me
35 but that's dirty so those need to be
cleaned
okay
32
31.
25.
won't mess with the drop target yet
spinner
that's number five
37
38
39
40
down there
26
also 26.
one's not working
19. these things are real temperamental
these little rollover buttons
it's probably just misadjusted they have
to be really close it's hard to get them
just right
one three and four
34.
33
27
one
ah that's about all of them might be a
couple more that i missed but i think
that's about it
yeah
okay so now we can try to drop targets
24
23
22
and 21.
um there's trough switches but we kind
of know those work already
so it looks like all the switches work
fine uh with the exception of a few of
those rollovers at the top
and the kickers need to be cleaned
let's try a game again to see if we
fixed our vibration thing with the
flippers
all right so we'll start a game
need credits
well
oh there we go
you can hear how bad the sound is
it's coming folks we'll fix it
[Music]
all right it found them we're good
all right so
when it hits that it knows that it's
left the
the out lane
i mean the
shooter lane okay we have a thousand
points
[Music]
so
frank we fixed your scoring problem
buddy it was that switch
is that right there
it was that one frank
alrighty so i think we fixed that um
let's check out those ones on the top
that i was saying a neat adjustment i'll
show you what i'm talking about
okay we're still in gameplay i just
carefully lifted it up
now when you do this
take the balls out or you'll regret it
because i always fall
and then make sure you're pretty steep
because all of this junk on the bottom
of the play field will make that damn
thing fall back and kill you
almost killed me once be careful be
careful folks
okay so here are the little rollovers
these are special little things
that just have a little tiny bit of
movement
you see how that is so i'm gonna push
that one and you can see just how like
it doesn't move very much
so it's not quite touching it
i mean it is a little bit
but if the contact's dirty and it's just
barely touching it that's not gonna work
so you gotta get that thing adjusted
really freaking close or it's not going
to it's not going to score now see the
little bent blade there in the middle
and how it
it's kind of touching you know so that's
kind of trying to do its thing but we
need to get that a little better and get
it get those contacts clean so i'll do
that and then we'll test them again
okay
[Music]
so you get dial tones
so this is the same one we were just
looking at i believe
that's how it needs to be people
okay so i think we've got the switches
doing their thing i'm gonna play it a
little bit just see if anything else
pops out at me
um and then we've got to work on the
sound now i believe the actual
background music
is fine it's all of the synthesized like
the woman's voice and stuff that's not
right
magazine on
very crackly
[Music]
we're getting we're getting we're
getting no extra points
so that's good
[Music]
i i cleaned the uh
the kicker switches too
[Music]
[Music]
uh
[Music]
[Music]
i forgot about the ramp shot
i don't like that the end lanes are a
little bit bent a little weird
we'll have to work on that just a little
bit maybe bend those a little straighter
[Music]
oh
did you see how the drop trucks
they dropped themselves they call those
memory targets they're wonderful stern
was the first one to do those
[Music]
c9
[Music]
[Music]
kickers are much better
[Music]
they're just doing that to tease you at
the end of the game
okay
it's playing pretty good there may still
be a little bit of stuff but we need to
get that sound fixed so
onward to the vocalizer board
all right folks so how are we ever going
to figure out what the sound problem is
now
i'm no expert but we're gonna figure it
out
this is the sounds plus module they
called it
okay
so here's how you figure it out you
start you work backwards okay so
to the loudspeaker so that's literally
where they plug in the speaker
okay and so you if you work back if you
look
it runs through the amp which is a tda
2002
that's the little tiny
amplifier that works on this
and then look right here
you have this
line here
you have this line here
coming to what they're calling the
speech control
and then the the feed for it comes from
what they're calling analog signal
which runs off the sound board so the
the way this thing uh
is made is there is a sound board and
then there is a voice board
the vocalizer board
so this analog signal here is coming
from the vocalizer board going to a
thing called speech control and then
being mixed into the amp
well clearly that's where the speech is
coming from then we have the speech data
and a speech clock line that run over
here
up to a
6820
6821 pia chip
okay
so that's that's basically
that chip is controlling what the sound
board
does
with the eproms on the soundboard but
the analog signal is coming back here
well it sounds like it's playing the
right stuff it just doesn't sound very
good
analog signal
all right if it wasn't playing or it was
playing the wrong stuff it might be
something on that board that has to do
with the
with the uh
the roms or whatever
on this on this particular generation of
stuff if you're missing entire words
like they're they're saying things and
like there's a word missing in the
middle a lot of times it's because
there's an eprom screwed up
okay but if you go farther back
before
that speech gets mixed in look it keeps
going this is now we're working
backwards right
and this says volume
there's a lm 3900 that's a preamp
and back before this
we have a signal coming from
an ay3
8910 which is an old school
audio chip that's used in a lot of
arcade games donkey kong i think uses
the same chip
ay3-8910 now the way this thing works is
it's controlled by solenoids
from the mpu it uses the solenoid lines
it just tells this what to do there's a
data line here that connects up to the
eeproms and all of that stuff
where it's it's software controlled
basically but here's the outputs
there are three channels that can output
on this chip but if you look they've got
them all three tied together
okay
all three of them tie together
and lead into what we were just looking
at so that's the source of all of the
digital music like
doing all that stuff we're hearing
that's this chip doing all that
all of the speech which seems to be the
problem is coming from the other board
through here now whenever you're getting
garbled stuff
it's usually a capacitor
it looks like that board's been capped
before though we're about to pull it out
and see but if you look the speech runs
right through a capacitor right before
it's mixed
i mean right before it goes into the amp
that's highly suspect right there folks
that's the one right there that's highly
that one there
that one's highly
come on come on people
come on if if the sec
if all this works and this
if if the sound it
come on now if all of this
if all the speech goes through
we're only having a problem with the
speech if all of the speech goes through
there it's probably there
come on now come on come on people we
can figure this out come on now
all right so there is the sounds plus
module
look how it's had all the caps replaced
but it hasn't had all of the caps
replaced
what is this
uh what c25
what it huh that one hasn't been
replaced you say
we'll look into that
uh
and here is the
vocalizer
module
so this does all the voices now it you
know has to create that analog section
that it was showing which is going to be
this down here
and it's been reworked as well
so it could be something down there too
right but we're going to start with the
actual sound sound board first now joe
said that he already looked at this a
little bit and he left us a note
inside of it
uh he already diagnosed it so
come on joe
joe
okay
pete this got to stop people come on
come on now
come on joe
okay so i have pulled out the sounds
plus like i said someone has already
recapped most of it so the
uh speech
comes in
through this capacitor now you would
you'll notice that on the
schematics it was marked as polarized
and it's even marked on the board as
polarized but it's a non-polar ceramic
cap
so the thing with ceramic caps is they
don't usually go bad
so it goes through that
hits a little resistor
and then turns it goes into the
potentiometer now that potentiometer
that could be our problem ah yeah
since that one's a ceramic i have
changed my guess too it's the freaking
pot look at it
look how ugly
now you probably uh if you don't work on
these a lot you probably don't realize
that that's a really bad potentiometer
these things suck
they're just
crap that thing's gotta go
oh
it's just made really cheaply and while
i'm at it that one's gotta go too
so i think what i'll do now this is just
for testing purposes people
they've already replaced the capacitors
a ceramic disk capacitor i'm gonna roll
the dice on
um
so i think all i'll do for now is
replace those two and pop it back in and
let's see what happens now what is this
oh that's cool too i thought it was a
mylar that's a ceramic as well
so yeah if i had this just sitting here
and was trying to decide what the issues
were the first thing i would look at
would be those two now
this also has the dreaded lm 3900
preamp here
these things are known for going bad but
it only does the music you saw in the
schematics it doesn't have anything to
do with speech and the music sounds fun
so you might say if you're a logical
person you might say okay ron well if
you're going to replace that speech one
why are you replacing that on the
schematics that one doesn't have
anything to do with the speech either
that's a good point i'm glad you brought
it up it's because that's the exact same
thing as that so we're saying that
that's bad but then we're going to leave
one that's just like it on the board
uh-uh
not on my watch
if that one's died you know that one's
right behind it
these are just really cheap
potentiometers uh and they don't have 50
years in them you know so
they're at 42 years
it's it's about done
about time to put a new one in it so
it's a 1k potentiometer i'm just going
to swap those two and we'll try it back
in the game with just that improvement
and see if that changes anything
okay so i swapped them out with new ones
now these are not much better than the
other ones they are sealed off though
where they don't get as much dust and
dirt in them but same situation in 42
years whoever's watching this video
on serial number
11985 time to swap them buddy i did it
in 2022 now it's your turn mr 2064.
uh yes we're gonna roll the dice on c25
it
i just it's a ceramic one i think it's
probably gonna be fine but
we'll see
that didn't have nothing to do with it
when he brought it he said that it was
uh that sound was cutting in and out
which is what it's doing right now so um
that's not it
i've got an idea what is it though so uh
we'll pull the board back out
all right so if you looked on the
schematics
everything was kind of controlled by
this 6821 and look at the legs on it
who'd have some hairy legs
and then here's the cpu
that's the ram
that's a new eprom
and then here's the sound chip so what
i'm going to do is simply remove those
chips clean the legs and put them back
on the sockets
i think there's something intermittent
there that's my guess at least
so just so you can see what i'm talking
about look how filthy these legs are
can power get through that i don't know
i don't know folks maybe a little bit
and then it turns itself off
so i'm thinking it's an intermittent
connection either on this or the 6821
this one looks pretty clean that one's
new the sound chip looks pretty clean
but i'll pull all of them now you might
say well why didn't you do that a minute
ago because i'm making a video people
come on now come on i'm trying to make
it interesting
we now know that that was not the
problem when it sounds like it sounds
so let's move on to these
here we go
okay so to quote paula abdul two steps
forward two steps back
okay so we're in the middle of a game
but i figured it out
if you flex it
it comes back
i don't think it's this connector i
think it's the whole board
flexing
so we've got a socket issue
however that's the two steps back let me
show you the two steps forward if i can
get it start again
let's see
if i can get it to start again come on
now
i had to do it about five
times earlier
it may just it may be that
[Music]
okay
that's how it's supposed to sound so it
has something to do with this i may have
to re-solder this connector maybe
it could be let's try that
okay so that ribbon cable let's see if
we can tell if it's the connector or the
actual cable
too far
i won't uh
i won't curse like ave does
[Laughter]
he doesn't like it when things go out of
focus
those don't look that great but i don't
see any of this just jumping out at me
but you know what i'm gonna do
i'm gonna re-solder all of those
and then we're gonna go around to the
actual pins
let's see what these look like right now
i don't know that all looks decent
okay so i'm going to resolder them
we'll do that first okay so our theory
is if the ribbon cable loses one of the
address lines or data lines that it
kills all the sound now why would it
kill all of the sound and not just
the sound from the vocalizer because
it's making the background sound cut out
too it's because of this little jumper
that jumper g right there you're
supposed to put in if you don't have the
vocalizer board
so what that does is it ties one of the
outputs
of the 6821
to the chip select
on the eeprom on the main board
pin 20 there
if you don't have that jumper in then
you need the vocalizer board because
that signal comes from
off the board over on the vocalizer
board
so that line on the vocalizer board
appears to be this memory enable
line which is
created from this chip by a bunch of the
address lines
[Music]
okay folks i think we're tracking it
down i think i about got it
all right
so when i put it back in
no sound
but then i hit the sound test button
got all of the sounds
okay
so
at that moment
basically the mpu wasn't able to turn on
the sounds but the board itself could if
i hit the button so that means it's a
connection problem
between the mpu
and the sound board okay
and then after playing it for a little
bit cut sound cut out again
[Music]
uh this didn't seem to have anything to
do with it now remember whenever you
flex the board you're flexing all kinds
of stuff right
and so then looking on the schematics
the mpu the way it turns on the sound
is through this uh
4049
chip here and then into the sound chip
okay so basically it's in signals
through this chip into this chip so that
wasn't working right works sometimes
sometimes it doesn't
okay if you hit the button
you're bypassing that chip
you're controlling it without that one
right
um you're not basically you're not
turning it on with the same inputs on
the sound chip so i thought hey let me
swap the sound chip
just for giggles
so i swapped one
and it seems to be working really good
now but
watch this
so i think the socket on the sound chip
is tripping
[Music]
but the good news is
the chick sounds awesome
[Music]
so we're getting there i kind of want to
turn the scent the
i want to turn the speech up though
let's see if i turn that up
we want
we want more speech
than background
[Music]
did i go the wrong way
[Music]
[Music]
yeah okay so that's what the xenon sound
basically all the way up compared to the
uh
i think you can turn the background
sounds down with this actually
there we go that's gonna do it
okay so the background sounds are down
[Music]
that's how you want it
okay um
i'm gonna pull the board out again
and put a new socket
in that sound chip
and uh see if that gets it where it's
sturdy
okay folks
so while i was at it i hated that
insulation displacement connector so i
went ahead and replaced it too
and
[Music]
it does not like when you touch that
not sure what it is but it's some kind
of
a bad solder joint somewhere
i wonder if it's one of those vias
it's in the center of the board flexes i
replace the 4049
[Music]
so it's time to reflow a whole bunch of
the board
and just see if by accident we find
what's making it do it
[Music]
crazy
oh i tried a different ribbon cable too
had nothing to do with it that's the
same exact thing
okay so now i'm going to take it and i'm
going to reflow a lot of these vias that
go in between
the new socket on this didn't fix it so
something strange going on
this freaking soundboard is driving me
crazy i want you to look at this
okay now watch how hardly anything moves
but this little section of the board
[Music]
do you see what i'm doing here i'm
moving it a millimeter
for our uh european friends
[Music]
what in the hell is that
got to be a bad trace it's got to be but
i keep looking i cannot see a bad trace
all right i got to go look at it again
it's got to be something right in this
freaking corner of the board
that's nuts look i can do it over and
over again
it's barely moving this but
i'm trying not to
[Music]
i can almost play it like a theremin
[Music]
[Laughter]
you know all the fun things in life are
free people
i mean i'm getting paid to do this but
every time you find out something really
cool in life it comes to you free
okay so the area i was flexing was this
area right here
so this board this is where it sends the
signal in and then it sends it through
these pins
to these little resistors
i mean um yeah to these resistors which
run to this
uh 4049 that they're using as a hex
inverter buffer
there you go
uh
but i was just looking i didn't solder
that
our buddy frank did now frank i'm not
going to criticize
your soldering skills but i think there
may be a bad connection
on one of those solder joints
so i'm going to remove the solder and
see if the trace is screwed up under
there or something
and then if you look over here see how
just above the resistors there are
little cracks in the
little scrapes on the traces
it could be that too
so i believe the way this thing works
i don't know for sure but it's basically
it's using the solenoid lines and if you
check it with a with a logic probe
there's a little pulse every once in a
while
right so it's sending some kind of
signal
and it may be that it needs a signal on
all four of those lines in the manual it
says there's five lines but there's
there's really only four one of them's
not hooked up to anything
i believe it's on pin 12. one two three
four five six seven eight nine ten
eleven
that might not be right one two three
four five six seven eight nine ten
eleven
that might not be right
but uh one of these doesn't actually do
anything so there's a solenoid line a b
c d
and e but e isn't always used or
something like that i don't know i may
be wrong
but i'm gonna i'm gonna take the solder
off of this and check out this connector
um we may just need to swap the whole
connector
so that's my next guess
well the bottom looked okay but the top
this trace is broke i don't know if i
did it or he did it though
so i'm going to clean this up
put a new connector on it
of course i haven't cleaned that up yet
that's just
taking the solder off
but i don't see any broken traces
leading up to here
so
but i'll clean that up real good and
test it with a multimeter and all that
i'll show you what it looks like with
the new trace on it for this one
sorry where it's broke
here what you can do is if you've got
enough room and usually you do to get
the pin through the hole you can put an
extra like a cap leg or something up
solder it to the trace
and then through the hole and whenever
you solder it on the back it'll make
sure that
solder flows up to the top and also that
you got a good solid connection to that
trace you could also run a jumper wire
if you needed to
all right it's been making this
suspenseful music
for 30 minutes with no problems
[Music]
see he said it was intermittent so i
gotta i gotta watch it for a while right
let's see
if it does this thing again
hold on come on people come on now
now you might wonder why do i care if
you have to push on it just don't do
that right
but
he's going to pick it up and take it to
his house and what if it breaks again at
his house
[Music]
i'm almost afraid to touch it
that's it joe
we fixed it joe
hey we fixed it
all right so now we got to test play a
game to make sure that it doesn't cut
out in the middle of a game
i'ma turn it way up
okay we're going to test it a little bit
didn't hit that switch
[Music]
wow
[Music]
missed it
[Music]
[Music]
oh missed it again oh almost got the
bounce
[Music]
missed it
i think we might be sitting a little
i'ma blame the level
frank doesn't have it level enough
try tube shot
i'll try
[Music]
i gotta
i gotta mess with that in lane
missed the tube shot
i need to get the spinner
[Music]
boy the lights are going now you ought
to see the backlash you'll just have to
trust me
it's going nuts
[Music]
lock that one
hey i like the ball joe
joe gets excited whenever we uh we we
finished one
still needs a little work dude then we
get the money yeah joey's all about the
money the cheddar
[Music]
needs a few little little playability
adjustments that need to tweak
i saw that
but all in all it's doing pretty good
[Music]
did i like the other one what happened
i was distracted
it went down people
all right that's four
ball four
[Music]
all right folks so we're gonna do
another video where we play through it
and show off the art and all of that
but for now
i think we've got it repaired so
for most of it repaired we'll do some
little minor tweaks
but that sound board issue took forever
so leave your comments down below
[Music]
well they were happy
with the video
oh well we had the quartet come in yeah
and they weren't even taking a cool
phone
they could have gave us a little bit of
mr speedo or something but no no
they needed it
they needed more
all right so leave your comments
it didn't hit the switch it doesn't it
doesn't like it when it doesn't hit that
switch
[Music]
so leave your comments down below let us
know what you think so far
i'm happy to hear the sounds back
[Music]
it's the end lane joe it's that right
there it's messing me all up i was doing
great till that
that messed me up so it bounced
you don't want it to bounce you want it
to flow smoothly it wasn't so bent there
i don't know
he's been messing with it when he
dropped it off you didn't mention that
to him no you should have said hey frank
let me point out something to you buddy
uh come on now
come on now frank what are you doing
here but i don't even ask him what's
wrong with it anymore it's broke
[Laughter]
all right so
thank you for everybody that's been
supporting our channel too by using our
amazon links if you don't know about
that down below there is a link to
amazon if you click that it'll take you
to amazon so whenever you go buy your
porsche
if you buy it on amazon it gives us
three percent or something like that so
we appreciate everybody that's been
doing that and
last but not least try xenon and check
out my brother donnie my brother has a
channel here on youtube
we work on pinball machines arcade games
and jukeboxes he works on old vehicles
and old buildings things like that a fun
time is had by all so we'll see you over
there but we'll do another video of this
where we play through it and
spend a little more time with it because
it's such a nice game see you then