815. Hand Build a Roller Texture Mug with Hsin-Chuen Lin~ a Class Demo at Palo Alto Art Center

Hsinchuen Lin
205 followers
55 Video Views·Jul 28, 2024
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more information, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
so after to roll that slab this is about
this stickle it's about4 of an inch and
I'm going to apply the texture to the
surface
first and then I you want to make sure
that the clay is sticking on to this
template so what I do
is brush some water
right make it wet and then you don't
reserve a powerful
base stick apply a bit
pressure Reserve that power for
all right so this will be for the
bottom right again slightly overlapping
here right overl
in and you can open up uh this part here
open up a
bit and this part here you open up
have something smaller to
support right support it on the joint
could be overlapping or it could be like
we did 45° and with a little bit support
on the inside
so if you were going to do 45° do you
leave a bit extra yeah yeah if you want
to do 45° and then you when you cut it
you you want to have a little bit extra
here so you have more room to do that
okay cut don't cut but you're going to
do the 40 yeah leave a tail so this one
is uh it's
overlapping so I will I just have about4
in additional overlapping and then when
you when you use a roll to rad it little
bit support there
um so that you don't have too much Clay
on the overlapping
part here you could and this's
one supped
it looking for the all right and then p
on the table so that the base will
be okay that's
good and then if you want to disguise it
usually um you can put the handle here
right so handle will disgu your same
line so you yeah you don't need to worry
about too much um if you want to do that
if going to put the texture back on it
make sure you do put a support right you
put a support there and then you do that
to roll it just a little bit put some uh
texture there right
so yep it's fine right yeah but here you
might want to about make sure this part
here you don't have line but if you want
have a line there that's fine because
it's hand built so sometimes leave some
trees some uh working process yeah so I
would have about too much having the
line
there can you can open up this
here basically just for four minute like
when you you picking it up make sure
that it's nice especially the base
before you attach make sure you have a
nice Perfect Circle here and to make
sure this part here is
flat so just lightly P it on the
table and
then just like we did our project right
and then attach it and make show
you you don't leave this a little bigger
like the
uh you could yeah if you wanted to you
can leave it slly bigger but I'm just
going
to no where is
our P slip not and the pressure SSP
right okay I didn't cut it all the way
through you can cut it all the way
through later you don't have to do it
now but you want to know where is the
joint right so you just use that to
trace it
make sure this perfect
circle before you press
fmer and slightly pick it up and drop it
on the table use the gravity
to moment the
pressure right
that's how to form your cup and then for
the handle right handle you can use you
attach the handle later but let me show
you how to do the handle
um if your hand is not quite even or you
want be able to roll it evenly there's
the
technique
okay and then you make it flat sliding
okay um if you don't want to put any
texture can just do
this okay for one side and you dra the
other side SM the edges smooth the edges
also I push it so it's not a thick yeah
my personal preference is that the edge
is slightly smaller than the middle
section so when I'm out rot it you see
that I'm rolling it this way more
pressure down so that Ed is is
thinner make your hand well usually the
rule of thumb is for this size of MTH
two fingers to go through
easily complete three fingers you don't
need have all your fingers unless your
your cup is very big then you need these
are four fingers but two fingers should
be strong enough to
hold
the right so you can put the texture on
hand just let it
sit it sit that is sit until you FM up a
bit and then you attach it
and can you demonstrate theing M yeah I
will do the demonstration the attaching
later okay
okay all right so the the handle is
sitting there for more than 30 actually
45 minutes and it's firming up now I'm
going to attach to it let find the ugly
side of maybe the simar here is good
place for you handle
right and you cut a slightly curved to
follow the curve of your
mug so it was a complete
circle it's work but Clay is soft so
doesn't need to be exact just let the
curved and uh again
score score here too right this is where
you are going to attach
it and
actually for making the mug I personally
prefer using my fingernail to kind of
knock it tap it to make it open little
bit wider it open
up and the reason I'm doing so is when
you open up you have more surface area
attaching together so it will be
stronger and also additional clay see
that the little additional clay it's
good for you to blend them
together so
make it slightly
bigger and slip if you don't slip use
toothbrush just make the slip right on
the
spot
okay put your hand behind it inside
little bit support and then and slightly
squeeze squeeze the handle
off and remember pressure is important
so you want to squeeze it make sure it
is attaching
it okay so that is attached and now you
need to decide
how big for the opening and normally I
personally prefer two fingers right two
fingers to be able to go inside more
freely so that is a good space for two
fingers and that is probably good okay
and then this will be the spot that I'm
joined again
yeah Ed little
SL right and then put your hand behind
it make sure this is straight right so
this is little bit off move it to the
right before you compress the firmer do
the adjustment and see if that is
good that look looks good and then you
just cut the accessive clay of the
bottom before you compress it firmer get
get a drip of water there right by the
corner
okay put your hand behind it both hand
compressed
it okay so that is how we attach
handle get everything right you see that
I cleaned up all my rim and get it level
and then you attach you handle the LA
right good
[Music]
[Music]
