865. Complete Guide to Throwing a Teapot with Hsin-Chuen Lin

Hsinchuen Lin
205 followers
232 Video Views·Jul 31, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
try to get the corner of a clay. So, my
right fingertip is holding on the corner
and I kind of pinch it in when I'm
pushing the clay down. And then open the
hole, use my right thumb to drill the
initial hole,
and then um my left hand go in there and
maybe my thumb can help it to brace it.
and take it all the way
down to the very bottom.
Usually, um, I leave it about between
half of inch to 3/4 of an inch. And once
I reach that, I'm going to pour toward
my right hand. Use the fingertips. My
right hand is always brain.
And then I just go back there and
compress it.
So that is for the floor opening and
since my um my opening is low so I can
use my thumb to do that too.
And if you have a hard time to do so
I always show you that um using my
compressing stick you will be able to
achieve that easily. Just push down on
the right hand part.
Focus on your right hand side and you
can get the base flat easily.
Slided it t it downward so that the
center is flat.
Okay. So that is using the compressing
stick. And then after that just pull and
lift from the corner and just lift it
up.
Pinch and my right hand is bracing and
all the clay is under my control. Pinch
and then I lift it
and compress the rim.
Bring the corner of clay in so that you
get to use all your clay.
And make sure you lubricate it. Make
sure the corner is sharp. So you can do
use your fingertip to make it sharper
that corner.
And then I'm going to leave it again.
And now my thumb is a little bit short.
So I'm extending my right thumb but
still lift all together.
compress the rim
and make sure it's slippery and slightly
color so that the opening is a little
bit smaller.
Two pound of clay is a very good size of
a teapot.
Make sure everywhere is lubricated. I
just
stick my hand into the water and then
just brush it on the surface. I'm going
to do it again on the same way the thumb
and the fingers and the bracelet all
together.
And this time I'm going to slightly
increase the volume.
And then on the top I squeeze it in. Use
my thumb to squeeze the clay.
So the opening is smaller.
Okay. And now I'm ready to make the
shape. I'm going to make a a slightly
curved belly. So, using the metal rib,
push that wall against my rib outside.
And the opening is slightly too big cuz
um you don't need to have that opening
very big for your teapot. So I'm going
to pour it in from here. Make sure it is
slippery.
Um, just use the finger inside and then
the thumb outside and kind of pull the
clay toward the center.
See that? This is my finger inside to
support it and the thumb outside to
pull. And maybe I can use my metal rip
to help to squeeze the clay too.
and compress the rim.
And you can see that the the key is the
little bit of a fingertip supported on
the inside and the outside hand is
pushing.
So you always have support on the
shoulder
and you can squeeze the clay toward the
middle.
Okay.
There's some residual slip on the inside
before I finish up the rim. get rid of
it while you can have your fingers, your
hand go in there. So that you don't need
to use a stick with a sponge to get them
out while the opening still bit.
Can just use your hand to reach inside
and do that.
Maybe uh do a better job on smooth out
the inner part the base.
I'm going to make it even slightly
smaller on the rim.
Usually I prefer this way of making a
lid teapot like lided jar so that to
keep one part simple. There are a couple
ways to get rid of the skirt of the clay
in the corner. So I have uh this wooden
knife. I'm going to use a wooden knife
to just shave it and then clean it. Or
you can use the wet trimmer. This is my
number 17 wet trimmer to do that. So,
let me use the wooden knife to trim the
skirt clay off the corner.
Just slowly
cut it down until I touch the the back.
And then use my number 10 knife. a
number 10 knife. It's very thin
to go underneath and the more horizontal
the better until you see the tip and let
it go the full circle and then you can
cut it and remove it easily.
Okay, so that's one way to do that
or you can use the um the wet trimmer to
do the triming.
I use this against the back and then can
remove the collar easily. Okay. And then
you can hold it the the tool sideway
too.
So you can trim a little bit off the
corner.
That's why you call wet trimmer.
Well, I'm going to trim the the foot
anyway. So it really doesn't matter that
much. that if you put that little
decoration rim in the corner.
But uh in case you don't want to trim
the base, this is a good way to to set
it like that. So it looks like a
finished piece. That's the body of the
teapot.
Good size teapot.
And then you can choose to wire it up
now or can you can choose to wire it up
later. Usually I wire it up later
because sometimes if your wire is
thicker when you wire it up, you might
alter the rim. Okay? So I let it sit a
little bit while and then let the the
the rim firm up a little bit and then I
wire it off. Okay? And just pop it off
from my bed system and put it aside. So
that's the body of the teapot.
Now let's make the lid. So I told you
that this is about 10 oz.
Okay.
Right. So this is the inner part of the
the rim and I will make a lid this part
here to fit. And my preferred way of
making the lid is I will trim the knot
later. So meaning I would make the
gallery now and then let it dry and then
flip it over and trim my knob. That's my
preferred way of making the lid.
Since I am going to trim the knob, so I
could make my base slightly smaller.
So I usually tell you who have watched
my video previously,
you center your clay into a doll n
shape, make the shape like a do and then
make it slightly taller because you need
to have a bit of a room for your nub
so that your nub will be taller. Okay,
you don't leave it too short. Okay. Slip
quite a bit of clay here and then work
on this part here to make a shallow dish
first and then squeeze out to your
gallery.
So now I am making a shallow dish.
And remember you are making a gallery
here. So you want to make sure this part
here is slightly thicker. You have more
clay to work with.
So you keep on pulling it outward
and let's double check to see how far I
can go. So it's pretty pretty much very
close. Now
this part here will be the in the Gary
will be drop it inside the body. So
that's pretty good size. So I am going
to just make sure that inner curve is
nicely down before I take care of the
gallery.
And for the gallery I'm pinching here
using thumb do fingers inside. And then
this index finger just draw and squeeze
it. So you can see there's a gallery
shape forming in here already.
and continue clean up the inner part.
Right.
And now you want to use a nice 90°
corner. So this is my number one wooden
rib. This corner that shock corner is
very good. So, I'm going to use the
shock corner to just push it down with
one of my finger inside to support it
and one of the thumb outside to support
it and just
squeeze it down.
Okay. So, that's how you how I form the
gallery using this shot corner.
And let's double check it. See that is
slightly too wide. Okay. So I'm going to
push down also squeeze that using the
the rip to squeeze it in a bit
down and squeeze it in a little bit.
Let me double check it again.
Right. So this looks good to me. So I
will stop right here. I tend to make
this part slightly wider than necessary.
So later on I could trim it so that the
lid and body is fit in perfectly tight.
And also I slightly taper here so it's
easier for this part here to drop into
the body. So slightly angled. And if you
some people do make this part here
slightly higher. So when you pull your
tea out it's stuck right there. So
that's one other way that if you want to
you don't want your a little too far off
you can make this part here slightly
taller.
And here the gallery is hanging out too
much. And you can use a
knife to just cut it off.
Okay. So it will be smaller and better
looking. That's good. And then smooth
out here.
Then just chop up the clay
from the corner.
Okay. Again I will w it up later. Okay.
So that is the lid for the teapot.
Now the spout
3 oz.
So this piece of clay is small. So I'm
just using my fingertip to center.
Right after that, u drill the hole all
the way down to the bed.
and lift it up.
Brush the rim until I'm lifting.
Make the spouse smaller coloring in
fingertips work.
Making this part just lightly it run
and then squeeze it smaller to get the
spout.
And before throwing a small thing you
could increase the speed of the wheel.
Right.
Then down this B here
in it.
Pull it up.
And then put a stick of uh any kind of
stick even your uh needle tool to
support on the inside.
Okay. and support inside and then use my
thumb. Okay, this thumb
push that against
that stick
to thin it down. So this part here
is not too thick.
Okay.
And compare the the size of the spout to
the body. Slightly too big. So I'm going
to make smaller.
So that looks good. And it doesn't
matter that the rim is not even guess
later on we are going to cut it off. So,
it really doesn't matter. All you need
to do is make sure the surface is nice
and smooth.
I'm using my shammy to smooth down.
Okay.
And chop the clay at the corner.
It really doesn't matter to have that
little ramen cuz later you're going to
cut it off anyway. So, it really doesn't
matter
the bad. And then u I usually dry this
bow uh the surface a little bit and then
uh do a little bit of shaping. I like to
have slightly curve so it's easier or
it's more beautiful to look at when it
attached to the body. So little curve
looks better. It's my personal
preference. So So I used my torch.
Right. So now I cut the wire it off and
then do a little bit of a sculpting.
pick it up from my bed and then I
slightly
check to see which part is it slightly
higher. So this will be the bottom part
of the spout. So I'm going to bend it
from here. Bend it this way.
Like I say that you don't want to get
this part here too dry. If you you do it
too dry,
you it will start to crack from there.
So make sure you don't dry over dry it.
And here you see that the hole and a
little bit of that it really
not necessar not necessary to have that.
And here is the center point. Okay.
Center point. So I will cut
cut it off here. Cut it off here. So
that is where I'm going to cut it. Okay.
Just draw use it my needle to draw a
line
and then just shape just cut it off from
here.
That's how it look like on the inside.
And then here
you see that even I'm bending here this
part here slightly dent. Okay. I don't
know if you can see it from that angle.
This part here slightly dent. Okay. So,
what I'm going to do is my hand goes in
there. Okay. Go in there and then
slightly push. So, it follow the way
through.
So, it follows
here. So, this part here is
all the way through smoothly. Okay. The
curve
Okay. Uh you can slightly pinch um here
before the clay dry. You can do pretty
much everything to it to form the shape
you like.
Okay. So, this part here is uneven.
That's okay. We are going to shave it up
when you're ready to assemble it. So all
you want to do is make sure that this
part here you pinch it so that thickness
is even.
And you can let it uh dry this way. Um I
will show the assemble.
Right. Just let it sit over here
and then when I'm ready to assemble I
will show you the whole process.
So this is the three parts of the
teapot. The body, the lid and the spout.
Okay. Body,
lid, and spout.
I will do the trimming and then assemble
to show you the whole process. Okay. So,
thanks for watching and see you next
time.
[Music]
