868. Throwing a 10 Lb Sodium Silicate Texture Lidded Jar with Hsin-Chuen Lin

Hsinchuen Lin
205 followers
698 Video Views·Aug 13, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
So, as you can see that I usually
center my clay, especially the large
amount of clay, I just uh center the
skin of a clay.
And don't bother to try to color the sky
high and and uh
push it down. So I will have less uh
less effort to center my clay because
I'm just moving up and down the skin of
the clay. So now clay is centered.
Okay, so that looks good
and then
drill my hole.
And by the way, this wheel is from BTH
and I've been using this wheel for more
than a year. I started uh I start to use
it last April last year
and I still feel very good and very
quiet.
Um powerful enough.
This is 10 pound of a clay.
I'm sure that the evenly I center 20
pound of clay should be fine to
work with it.
And also I'm not spinning my wheel super
fast. So at the lower speed it's super
quiet.
little bit little bit more uh noisy
maybe when you spin your wheel faster
but
I'm throwing at the lower speed so it's
fairly quiet.
So I tend to open my
larger amount of clay
a bit below so I could take care of the
flow.
My hand can reach inside and compress
the flow.
That's my usual way to open it.
Everybody does it differently.
And then after that I just gather my
clay together color
recycle my slips.
peel it up from my fingertips and toss
it in. And the for outside just put
little bit water on my hand and then
brush it over. So you can see that every
time after my throwing my wheel is super
dry,
my splash pan is clean.
That's because I use a lot of slip
instead of a water. And also because I
spin my wheels slow, so
the centrifug focal force is not toing
the slip of water to the splash pen
and try to use all the clay from the
corner. So
what I'm doing now with my right hand is
my fingertip, my right fingertip is
pinching the clay and move the clay
toward the center.
Squeeze the clay toward the center
and this hand is stabilizing while I'm
doing so.
Right? So this work as two uh two way.
One is using my right hand to squeeze
the clay and my left hand is stabilize
the cylinder
and then try to get the clay from the
bottom and
car to squeeze it up
and compress the rim.
My thumb is compressing while I'm doing
so. Sometimes I do this way, sometimes I
do this way. So, always get your rim
level and then remove the slip of your
fingertips and then toss it in.
And just a little bit of water to brush
it on the outer part. And since my clay
is fairly thick, so I'm going to just
squeeze it.
My left finger is pulling.
My outside hand is
just pulling.
And make sure before I
pour the clay, make sure it is slippery.
So you see that I'm taking my time to
get the surface slippery.
[Music]
Okay, I think I that uh
cuz I'm going to
push the uh uh brush the sodium silicate
over
and uh to do the stretch. So I'm not
going to pour it too thin.
So just smooth the uh the outer part of
the surface
and keep the rim smaller
just wide enough for my arm to go in
there.
Clean up the corner of the cray.
Before I brush the so stick, I like to
make sure my bed is clean.
Maybe I can pour it slightly thinner
here and slightly making a neck here.
but still keeping the rim thicker.
You can see that my splash pan is fairly
dry even I throw a large amount of a
clay because I use a lot of slip instead
of a water. Also, I don't speed up my
wheel. So the sensor freal force is not
touching the slip or the water in my
splash pan. So I could keep it fairly
dry.
So this is the uh sodium silicate.
[Music]
A little bit of sodium silic in your
clay or in your water is fine.
Let me use the torch. You can use a heat
gun or you can use a hair dryer. But the
torch is very powerful. So make sure you
don't overheat it.
All
right. So, I use a torch or heat gun to
heat it, heat the sodium silicate until
I see that the reflection, the shiny
surface goes away and then I stop. If
you do uh get looks too dull, it might
be too dry already. So, still a little
bit of a shiny but not too shiny.
Okay. So this is good. And then um I
will uh start to stretch it. And you can
use of uh your hand or you can use a
sponge or you can use a rip to help you
too. So I'm going to use my number two
small rip. Grab it on my hand and then
do the stretching.
[Music]
Oh, I'm using my number two rip
to stretch from inside. And here is the
shoulder. The clay is getting thin. So
if in case you don't want it to collapse
if you stretch it too thin, you can use
a heat gun to kind of focus on here to
dry a bit.
[Music]
All right. So, I'm taking my time to
making sure that uh the shape looks
nice. Nice view shape, the munja shape.
And then if you keep on, you want to
keep on working on here, you can
actually get a um torch to drive
further. So this part here is stronger.
So while you're working on here, it's a
lot easier. Okay.
[Music]
making lid for that uh bun jar.
I make the opening small so the lid this
lid will be very small.
Maybe my arm cannot get into the jar.
But it's for
for decoration.
Make sure the uh I reserve enough clay
for
trimming the knob.
So, I need quite a bit of clay, maybe a
couple
inches
for that. All right. So pretty quick I
make the leg and I will do the fitting
and terminate fitting later on.
[Music]
behind.
[Music]
