621. Trim a Thin-necked Twist Bottle on Stacked Chucks with Hsin-Chuen Lin 林新春 細頸瓶修坯示範

Hsinchuen Lin
205 followers
7 Video Views·Oct 8, 2021
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/potterysquare
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
Put three pieces of clay here to put a cushion in between if you have already trimmed this part
here. In my case I haven't trimmed it yet but just to show you that if you don't want to
chuck. This chuck has been base fired and it's very hard so put the clay in between to
prevent the chuck bumping into the body. And then the easy way to center this piece is that
you level it first. Level your piece and there are several ways to level it. You could use a needle
too and then spin the wheel and try to test it. The higher point you will draw a line and then
you just kind of move it. So that when you do this several times you should be able to
find your level. But I have an easier way that without doing trial and error is that
if you have this marble leveler just place it right in the center. But again this is very
important that when you cut your bottom you have to cut it very flat. Put it in the center and then
squeeze the clay so the bubble is in the middle. So that's pretty good and the whole piece is
leveled. Now you can center it. Put it on the chuck. I haven't centered it yet but now you can
just tap on your chuck or move your chuck to center your piece.
Right so that's how I usually center something like that with the thin bottle. Put it upside
down on the chuck and then level it first and then tap the chuck to center. And once you find
your center it's easy to just by using clay to hold it. You can hold the chuck a little bit.
I throw the chuck a little bit thicker so it's kind of heavy so it's not going
flying away. And also the chuck has been bisque so I soak the chuck in the water
for like 15-20 minutes depending on how thick the chuck is. Until you don't see the bubble coming
out. Because once you soak it in the water you can see that the chuck is absorbing a lot of water
and you can see the bubble is bubble coming.
And the chuck is soaked in the water so it's easy for your clay to stick on the chuck.
And I kind of stack up two chucks because the neck is very tall and the bottom chuck is not
tall enough so I stack two of them. And I put a little groove there so that the chuck is sitting
right inside of the chuck. So that's another way that you're gonna stick your chuck together.
Before you place fire you can trim it. Okay trim it so it's fitting nicely inside the chuck,
inside the groove. Okay so that piece is very good. All right and then I can start to trim.
I'm going to use my new tool, the looping tool. People call this pear shape or teardrop shape.
The new trimming tool to do most of the outer part trimming or larger area trimming.
And you hardly see me using the looping tool to trim. The reason why I didn't use it is because
at the beginning those are made of stainless steel and that the stainless gets dull and then
you have to resharpen it. And when you resharpen it the blade is very not very wide so after a
couple resharpening and the whole piece is gone. So that's why I don't use them a lot because I
always like to keep my tool sharp, very sharp. So I like to sharpen the tool before I trim.
With this tool that is made of tungsten carbide you don't need to resharpen it very often. Maybe
you could do it six months or one year depending on how heavy you use it.
And the carbide stays sharp for quite a long time. This tool versus my other carbide tool
basically they are the same. It's personal preference that if you worry about you know
you don't want to have a chattering mark. This is easy to get the chattering mark.
It depends on how you hold the tool. I don't get a chattering mark
but some people do see that they have a chattering mark.
So they prefer using the looping tool instead of the L-shaped tool.
Both are made of tungsten carbide so they stay very sharp for a long time.
This is also good for a corner making the foot ring here because you have 90 degrees.
Versus the looping tool, the looping tool they only have curve. So it's hard to
make a very good 90 degrees. So you will have a little curve
where it joins the foot and the body especially on the inner part. You could never get a very nice
perfect 90 degrees. So this is the carbide looping tool. You can use it for most of the outer part
trimming. So that's the carbide trimming. For the footing, this is my prototype.
It's still in stainless steel but later on I'm going to turn it into a carbide tool.
So it's the same design as this one. It's just the handle is smaller so that you could hold it for
more detailed trimming. It's a similar shape except for this part here is smaller and it's
an oval shape instead of a circular shape. So with the square that you could get a nice
turn it upside down and then trim a little bit here so that the curve follows through a bit
better. The camera can see that the clay is kind of like this. It's not like a tape so meaning the
clay is kind of dry. For dry clay, using the carbide tool is much easier. So I turn it upside
down and just trim a little bit here so that the whole curve follows through.
All right so people ask me what are you going to do with this tool. This is my number nine
stainless steel trimming tool and you could put the little circular
ridges here using this tool. Let me show you how to do that.
Okay so a little bit of ridges here for surface decoration, surface texture.
I can put it upside down and then maybe do a little bit of chattering so the whole piece is
it's a lot of texture instead of a plain surface. Or you do a sculpito carving
a little lines there too. So a lot of choices for putting the surface decoration.
All right so I hope this demonstration helped.
All right hope this demonstration helped and see you next time.
