We're an artist community (wire and metals) for everyone to share their ideas, post their art, tutorials/events & workshops or ask questions. We are a great buch of artists and have a lot of fun being creative together with challenges and fun projects to create every month.
To see what workshops I am currently running or to get full kits and or loose gemstones, frames for some of my tutorials, square/half round wire & more tutorials visit the shop section of my website:
Materials: - 150 cm of 0.8 mm square wire - 60 cm of 0.8 m half round wire - 30 cm of 0.4 mm wire - 1 x 5 & 6 mm copper beads - 1 x pear cabochon (mine is 30 mm x 30 mm) - 1 x 5 mm faceted - 1 x diamond cut gemstone
For exclusive content and more tutorials follow one of the following.
All right, so we're going to cut our lengths of 0.8 millimeter wires and our length of 0.8
millimeter half round, so just make it nice and neat, take your time, and I then trim off the
ends and just make sure that the ends are trimmed off pointing towards the stone, so that will
prevent any possible snagging in future when you're wearing the pieces. So next we're going to
take this and shape it around the stone, just take your time with it and use the stone to help you
shape the wire, and then simply press, take the stone out and then I bend the section at the top
and this is where we're going to bind the wires together, like so. So take another strip of 0.8
millimeter half round and wind a small section around the base, this is to secure it, and wrap
the tail around the one side just to anchor it in place, like so, and then just trim off the end,
make sure you maybe put your finger over the wire so it doesn't ping. All right, so next we're going
to separate out the wires at the top, so two on each side and then two towards the front, which
we're going to be using to create the bail, like so. Next take the remaining half round wire and
wrap it around the front two square wires and just take your time and keep wrapping, like so,
until it's about two, three centimeters, the length depends on the size, the length of the bail that
you want, so if you want it bigger you wind more, shorter you wind less. So flatten it out a little
bit to give it more strength and then simply bend around the bail, you can use bail making
pliers or you can use your fingers, bend it down and then bring the two tail ends of the wire
through the loop of the the pair and wrap the two legs, tails, around the bases, like I'm showing
here, and this will anchor the bail in place, so one or two wraps is just sufficient and all you
need to do is to anchor, so you don't need to go too much, so trim them off, you don't need those
anymore, you can use them later if you want to, if you have longer wires to create accents as well,
but in this case we're just cutting them off. So the next step is to set your stone, so what we're
going to put the bend in, so I'm going to separate out the wires first, so I've got a bit of a space
to put my pliers in, so do that on both sides, it's easier when you have some nails, there you go,
so next take your pair of pliers and quite close to the base, bend the wire in gently and that will
create a little cradle for your stone to sit in, like so, and then place your stone to see if it
fits and we're going to do exactly the same at the front, so again separate out your wires
and then just bend the wire over the stone, it will be slightly lifted as obviously the stone has
a dome, so just slide it over and this is what is going to keep the stone in place, so next we're
going to take the central two wires and pinch them at the top to keep the stone in place as well, so
this acts like a cradle basically, so next we're going to shape the accent wires at the top, so I'm
just twirling the two, so this is pretty much an organic design quite often, you know, go with the
flow, see what looks nice, so we are going to take the two tails on the side and I'm going to loop
them around and slightly wrap them around the frame once, but don't attach them just yet, like so,
then you can start having a look to see where you want these wires to sit, so we're going to do the
same on the other side, so just bend the wires on one side like so and see what looks nice,
so we're going to take them through the front to anchor these in place, sometimes
it takes a little bit of fiddling to get the wires in place, but it's quite satisfying when
it starts sitting in place, so pull the wire through and the trick is not to fight the wire,
just go with the flow and it will all fall into place, just choose a pair of pliers to wiggle it
and it will tighten up on its own, put your finger over the accent you've just created so you don't
accidentally pull it out of shape as well as you tighten the wire, so next we need to create a
little cradle, so I've made a swirl and this is going to act as a basket for our little gem, so
next I'm taking a five mil gemstone, now this you can use, you can use any type of gemstone obviously,
but with certain gauges of wire you need to use certain gemstones, so the 0.8 is perfect for the
size, you can go one mil as well, but I wouldn't recommend going any smaller than this, otherwise
it won't be strong enough to hold the shape, so just swirl it around the gemstone and just take
your time with this, the more time you spend on it the neater it will look, and just press it down
and then you can use your pair of pliers to adjust the shape very gently, and next we need to
create a little accent with the remaining wire, sometimes you can create more swirls like I've
done in my vine setting that is somewhere on the channel as well, or you can just have a single
one like in this piece and then use the round nose pliers to curl the ends like that, just
shape it to your liking, next take a piece of 0.4 millimeter wire and a, I think this is a six mil
bead, you can add anything, this is just an accent so it doesn't really matter what sort of size of
beads you use, you can use gemstones as well, this is just to create interest in the piece,
and then obviously secure it with your 0.4 millimeter wire, just kind of try and place
the wire in sections where it's not as visible, and anchor it quite securely so that it doesn't
fall out, do the same, I tend to use the same wire throughout, weaving wire or even my base
wires throughout my pieces, I prefer not to add in, so I just keep the wires that I have,
sometimes looks like an octopus, all right so now we're going to attach the accent wires that
we first shaped in the beginning, and I'm going to attach these to the frame on the side,
so where you put these again is preference, I've roughly shaped them around the top
to give it like a sort of hugging effect to the bead, right so now I'm using a needle here to
separate the wires out, it can be quite handy if you don't have any nails, so it's much easier to
get in between wires like that, and then I'm just shaping the wires here, and you can do that
at the end as well, I just like to do a little bit as I go along, next I'm going to trim off that
one wire that was left over, you could use it as well, I just, in this design I didn't really see
use for it, so I trimmed it off, obviously you can do something with it if you like,
next I'm going to reuse the same wire, 0.4 wire, and I'm going through the center to add another
accent bead, so I'm going to feed that through to get it in place, ready to add another bead,
so this time this is a slightly smaller bead, I think this is a five mil,
adding it to there, so again as I said you can use anything to place if you don't have any of
those copper beads, you can use the gemstone bead, microfacets is something that I really
like to use in my wire pieces because there's so much sparkle in them, and obviously secure it,
so then the wire that's left, once again we're going to reuse that, and I'm going to use it
this time to tie the tendril in place, now this is quite important because when you wear jewelry,
quite often, you know, you have it under a jumper or a shawl or something like that,
and tendrils like that tend to get caught, so I find it quite important to either tie
closed tendrils that have a bead in place to prevent things from hugging, snagging rather
than hugging, or tie them down like I'm doing in this case, it's especially important when you have
previously created a coil, a coil setting or vine settings, because if you snag and the wire gets
pulled and the coil gets bent out of shape, obviously the stone will fall out, so I anchor
these in place as securely as possible whenever I can, when I use it, so 0.4 wire you can use for
that, or you can use your half round which structurally is stronger, next is trim off the
remaining wires and look at once over and see if you finished, and that's it!