This was one of my earlier tutorials where I did not add US wire gauges so here is link to a conversion chart: https://jewelrytutorialhq.com/jewelry-wire-gauges-explainedI hope you enjoy! For updates on new tutorials, promos and discount codes follow me on social media:
We're an artist community (wire and metals) for everyone to share their ideas, post their art, tutorials/events & workshops or ask questions. We are a great buch of artists and have a lot of fun being creative together with challenges and fun projects to create every month.
To see what workshops I am currently running or to get full kits and or loose gemstones, frames for some of my tutorials, square/half round wire & more tutorials visit the shop section of my website:
- 1.25 mm (16ga) copper wire - 0.8 mm (20ga) copper wire - 0.4 mm (26ga) coper wire - 1,2,3,4 mm copper beads (one of each) - 15 mm round cabochon - 2 or 3 small pear shaped gems (1 - 2 cm) - LOS (liver of sulphur optional)
Chapters: 00:00 - Intro 00:11 - Frame 07:35 - Seating round cab 10:29 - Backing wire 13:42 - Seating of teardrop cabs 16:10 - detail Swirls on top
All right so what we need to start with is obviously the base for the heart shape itself.
So what we're going to do now is cut a piece of our 1.25 millimeter wire and we are going to find
the midpoint and create a bend right in the middle. Now bear in mind that this is much thicker wire
than your usual weaving wire your 0.8 or even your one mil will be a little bit more malleable than
this so you'll have to apply a little bit of force but just take your time and it'll be all right.
Now once you've folded the wire kind of lay the two wires parallel on top of each other and press
down slightly like so. Next we're going to separate out the two wires so slightly pull them apart.
Just do that gently you don't really want to put like a right angle in it's
just a very gentle curvature and then we're going to give the bottom a little bit of a
curve. Use your bail making pliers like so and pull them apart so just make sure that the wire
that's on top comes out towards the right. Next obviously we need to create the shape at the top
you can use if you prefer you can use something round I just do it manually and kind of shape
the wire. I find that easier for me but everybody's different I just find it easier to shape it by hand
because I can also control the actual shape so I'm bending it around. It's a bit of a fiddly job
at this stage but you'll get used to it if you work with it for a little while. So next bring
in your chain nose pliers and we're creating another bend so make sure that the wire comes up
towards the top because we're going to make sure they sit on top of each other again like in the
before at the bottom. So bring that in and pinch and then kind of form your heart shape if it's not
perfectly the way you want it right now that's okay because we can adjust it at a later stage
this is just to get the basic shape. Just bring that round and the wire on the right kind of
follows the shape we've just created. Just bring that together and then wind everything
around so this is the basic shape and you can then adjust the shape so I decided that I actually
like the heart to go in the other direction and that's it that's the base shape. Next we need to
attach the wires so what I'm going to do now is take a bit of our 0.4 wire and we are going to
attach this to both of those base wires both of our 1.25s just wrapping it around a couple of
times and then taking it around each of the wires once. So go over then under then wrap it once
around the base wire and so forth this will show you a little bit better so I'm rotating here so
hopefully to get you a better view of the way I'm weaving. So I'm going around the back then
around the first wire once all around both wires bring it in between the two wires and then go
around the other wire and just keep doing this repeat this process until you have done a good
section. So this is what it looks like so roughly about a centimetre or a centimetre and a half is
enough to keep the wires bound together. So trim off your 0.4 because next we're going to create
the basket for our round. So just use the longer wire that we had previously from the back and
we're going to use this to shape again you can use a something round but you don't really have
to as I said I personally prefer to just use my hands to shape and especially as you then
go smaller with the curls so just take your time and it'll look all right. This is basically also
just for the back so it doesn't need to be absolutely perfect. Keep winding until you
have got a good backing and then you're going to just trim off that bit of wire once we've
finished winding. Bring in your flush cutters I find that I prefer the heavier gauge flush cutters
because these wires are quite tough and if you use your fine cutters it ruins them so be sure
to use a pair of cutters that you don't mind to get some kinks and dents in it. So once you're
happy with the way the basket looks we're going to take that little piece of wire that you can
see at the front of the heart and we're going to curl that as well. You may need to trim it down a
little bit to about three centimeters long and this is what it's going to look like once we've
curled it. We are going to hammer this to give it a little bit more of a fatter appearance.
You can see here I'm curling this in and this is what it looks like so probably about two or three
centimeters long before you curl it in. Next we're going to hammer the heart so for that I'm
going to bring in my steel block and I'm going to use a chasing hammer as well. Just be sure to go
to the edge so that you get the wire flat and be very gentle when you hammer you don't really want
to mark your wires so just take your time and don't use too much force it will also distort
the wire if you hammer too hard. To get the little curl you can twist it open and obviously elevate
your steel block somehow and then hammer it on top. Now there's different types of hammers that
you can use that won't mark your wires. These are sort of rubber mallets that are quite gentle with
the wire so once you flatten it you can actually use the rubber mallet to get the wire flat rather
than the chasing hammer because it will stop the marking on the wire. All right so once you're happy
with that this is what it looks like you can see I haven't gone too heavy on the edges just to give
it a little bit of strength and a wider appearance. Next bring in your round cab and mine's a beautiful
amber cab which I've had for ages I thought it'd look nice in this perfect size. So shape your
little coil around the front of the stone and we are going to now use a bit of 0.4 millimeter wire to
weave around it to keep it in place. So bring that in and we are going to be attaching our wire to
the base just shift it in place and attach your 0.4 somewhere at the back somewhere close to the
the center of the pendant and just wind it around. I've used a shorter piece of wire here you need
about three or four meters of length depending on how much weaving you want to do. I just find it
easier to add in wire rather than you know work with one continuous length just simply because
it keeps kinking and is it's hard just hard to weave and it takes so much longer to weave with
rather than you know to add in wire at a later stage. So I'm just going to go a couple of times
around one of the coil wires that at the back of the gemstone then I'm coming across to the
front of the coil and this way I will sort of encase the gemstone. I'll go a bit up close just
now to show you what I'm doing. So you go around up and down a couple of times just to anchor your
wires in place and then we'll start a different kind of weave which I will show you in a second.
So just attach so here we go so I am going around five times or six times around the backing coil
like so just to create a bit of spacing between because we don't need to crisscross back and
forth quite so much and so if we add in a few coils this will give us a bit of spacing. Next
I'm going to go back to the front of the stone make sure I capture that twice and then I'm going
to go back to the back of the camberchant and start the process again so five weaves and then
you crisscross across the stone and this is what it looks like. Looks quite pretty as well so it
doesn't look like a dog's breakfast which sometimes the back of an other piece does. This is what it
looks like. Right next we're going to trim off that 0.4 I don't really need it anymore so just
cut that off and we're going to bring in our length of our first length of 0.8 millimeter wire
and we're going to create the backing with this so attach it somewhere near the center
to find the midpoint of that and attach it somewhere near the center of the pendant and
when you're working with thicker gauges at that length as well it's always a little bit awkward so
just take your time and attach and if you need to redo redo and I still had to redo as well so
it can be quite awkward to work with at this stage so just pull it tight and then go around
it a second time. I use a pair of pliers sometimes to press it down and you can see how I'm just
holding on to the wire on the left here I just find that easier you can unkink it afterwards
and I just find it gives me a bit more grip when I hold it like that so that I can put more
pressure on it. So next we're going to just twirl one section of the 0.8 around itself and that what
that does is basically create a basket a section where we're going to place our other gemstones
later on this is the backing so every so often once I've created a twirl I will come back and
reattach the wire to the frame this is just so that it's strong and not flimsy if you don't
attach it every now and then it won't it won't be strong so I'm just doing a bit of fast forward
here so you don't have to keep watching me doing this you can see I'm using my tools in between
to just strengthen the attachment and then I just keep winding until the whole heart is covered
and once you've used that one length of the wire you can then use the other side as well
if you have to if you haven't got enough there you go just go and keep attaching it to the frame
and that's it and that's what it looks like obviously you finish up the bottom section as
well I just thought I'd show you and this is the finished piece so far so good next we need to
bend in those wires so that creates like a an opening or a gap so that we can lay the stones
inside that basket so I'm squishing down on the attachments and putting in a sort of 90 degree
bend so that the the whole twisted section kind of drops below the level of the outside wire if
that makes sense next we're just going to trim off the wires we don't need them anymore so kind
of make sure that when you're cutting them off they are in the place where they can't snag once
the piece is worn once you've done that bring in the gemstones that you want and kind of arrange
them in a position that you like and I've decided to go with two pairs that point towards the bottom
and bring in another section of your 0.8 millimeter wire and attach it somewhere near
the bottom next bring in the one pair that you want to attach first and we're just going to
lay it in that little cradle the basket that we've created by pushing the wire wires down
and I'm just going to use that 0.8 to wrap around now this is quite a fiddly stage you'll find that
before the stones are properly attached and they tend to be quite flimsy and it's going to be quite
difficult to to kind of attach so just keep keep trying and keep redoing it if it kind of slips
out you'll you'll see just now the stone decides it doesn't want to stay in place and it falls out
so um this is just a fiddly stage no matter how you look at it so just keep keep putting the stone
back in until you're satisfied with the way it looks and then just attach the wires as you go
along it's quite important to anchor the wires sort of underneath the stone around the stone
to make sure it hugs the stone properly just go in and as I said earlier when the wires are quite
long like that they can be quite awkward sorry I'm going out of shot here and we're focusing
on getting that wire through so just feed that through and pull it up and just repeat that a
couple of times until you're happy that the stone is anchored go around the stone each time and
anchoring it below or or beside it and I've gone around it once or twice now and it's sort of
secure still obviously needs more work and now I'm just going to do a couple of decorative swirls
so I'm taking the same wire and I'm just going to go around the bottom and these are decorative
but will also help strengthen the um the attachment of the stone to the frame
right I've done both stones now and then this is what it looks like and all the stones are
anchored to the frame quite securely so just make sure that we've done that so next step is to start
with the um twirls over the top so bring in another section of your 0.8 millimeter wire this
is going to need to be quite long depending on how many swirls you are creating so I've attached it
and then shifted it to the left hand side I'm just always going to start from one side to start
creating the swirls so put these first together so rather than doing um the one wire like we did
at the bottom we are going to use both of them at the same time um to create a sort of thicker
overlay that looks much better than the bottom it just looks pretty I think so take both of the
wires at the same time and start by very slowly the first sort of swirl is always quite difficult
I find so just take time with it and just kind of bend the wire around itself this is quite an
organic design so just take your time and decide where you would like the coil to sit and let your
fingers do the work just very gently use a bit of force to pull the weaves in place just make sure
that you hold on to both of the wires at the same time you can see here I'm placing my fingers over
the wire that will help me to kind of create the shape and I just take my time with it if you try
and rush it it's just going to to be distorted sometimes the wires will kind of slip out of
place so just bring a pair of pliers to flatten them back down again push it in and as we did
with the the base frame we are going to need to attach these wires to the frame as well periodically
to give it a bit more strength otherwise it's just going to be quite floppy so bring it up
and as you go along attach it to the frame keep flattening it here with my pliers and decide on a
spot where I'd like to attach so bring both of the wires round and again because it's quite a long
length and it's going to be unwieldy a little bit but just take your time and it'll be all right
so just feed the wire through and wrap them around the frame pliers to pull them through
and when you pull your wires always put your finger or a pair of pliers over so that you don't
accidentally pull the coils out of shape so always fold something over them there we go and
this is what we're going to do all across the pendant so this is what it looks like so I've
covered the whole area around the stone so now what we need to do is as well attach some more
wire if you haven't got any left and we're going to go around the top right amber stone as well
so I'm just going to repeat the same process it's going to be a little bit more fiddly than
the rest because it's at on a thin edge I found that anyway so you might be different
and I just found it takes a little bit more um more time to complete just because I'm working
much slower you kind of just start and it's a bit flimsy as well because it's attached in an
position so just as I said take your time and it'll all fall into place put your finger over
it and your thumb and use your hands and fingers to help you achieve the shape and also don't
forget to attach the twirls to the frame as you go along and don't be shy to use your pliers if
you put any markings in the wire later on you can polish those off easy with a bit of sandpaper or
polishing paper just use your tools if you need to and then just keep wrapping around until you
have got enough swirls to cover the outside of the stone as I said keep attaching your wires as well
because that will give the whole piece a lot more integrity and it'll definitely be a solid piece
and the twirls won't actually fall apart you just keep twisting until you've reached the other side
so once you've finished we're going to cut off the wires that we don't need anymore so
um make sure as I said earlier to cut them somewhere you can push them in so that they
don't snag on any clothing that you're wearing later on and this is what it looks like so far
so the next step is to add accents you can use some more of your 0.4 millimeter wire
and then what I've used are some two to five millimeter copper beads and I've used two of
each except for the largest one and then just kind of shape them around the stone and attach
them with a piece of wire apologies again I'm going out of shot here and once I have attached
them I'm individually going around the wire and the base frame and attaching the wire in place
because it um that means it just won't it won't break if the pendant gets stuck on something
um and then just keep attaching as you move along and that's it so that's the last step
and we're going to trim off the wires and if you want to you can put this into liver of sulfur
which is oxidizing uh the wire and it makes it look darker so last step is to decide where you
want to add your jump ring and that's it and I hope you enjoyed that thank you for watching