Milling Rough Lumber Without a Jointer Using a Few Simple Jigs

D&P
34 followers
14 Video Views·Oct 24, 2022
In my shop tour video,
I mentioned that I don't have a jointer.
So then I got a ton of requests to make a video
to show how I mill rough lumber without one.
So here it is.
When you buy rough lumber like this,
there are no straight or square edges.
The board might also be twisted, cupped, or bowed,
not good for building.
And just like there are four sides to a board,
the milling process is going to be done in four steps.
So the first step in the milling process,
after rough cutting to length,
is to make one face of the board flat.
The ideal tool to do this is a jointer,
but we could get around not having the right tools
with just using a few simple jigs.
For this first step,
I used a super simple jointer jig at the planer.
And you might be wondering, if I have a planer,
why can't I just send the board through it just like this?
That's because a planer simply makes one face
parallel to another face.
So if you have a board that has a twist in it
and you send it through the planer,
the cutters are going to follow
whatever is on the bottom of the board.
So your board is gonna come out smooth on top,
but it will still have a twist in it.
Same thing for a cup or a bow.
This happens because inside the planer,
there are these rollers that put so much pressure
on the wood to help feed the wood through.
And since there's so much pressure,
it flattens out the boards,
if there's a cup or a twist or a bow,
as it's cutting the top.
But when it comes back out the other side,
it's going to spring back to shape
and it's going to have that same twist that it had
when you sent it in.
So that's where this jointer jig comes in handy.
And it could not be any simpler.
It's just a piece of scrap
that's attached to a long flat piece of MDF.
I got this idea from Colin at Woodwork Web.
So I'm going to link down to his video below.
He has a ton of information on this.
So here's how it works.
You take the board that you want flattening
and you find all of the high spots.
You could do that by seeing
that the board is rocking back and forth.
You could clearly see a visible gap there.
Just take a shim and put it underneath it.
And now when you try to rock it,
it's no longer rocking and it's stable.
So this board just has a twist in it,
but it would be different for something
that has a cup or a bow.
Like a board like this, you could see over here,
this board is cupped as well.
So I like to leave these thin little scraps around here
and I just would put them underneath in the middle
and get the appropriate thickness
for the piece of wood that I'm using.
So that way it won't flatten out
as the rollers are pushing it through.
The same thing for a bow,
you would do it in that direction.
But for now I'll just use this board,
make sure that it's not rocking.
And this one only needs one shim,
but normally when I'm doing this on like longer boards
or rougher boards,
there's like a lot of shims in different locations.
And to secure it in place,
I'll just put a dab of hot glue on either side of it
and then press it down.
This way the hot glue is securing the shim to the board
and it's also securing the board to the shim.
Because this board doesn't have so many shims,
I'll just add some hot glue to these edges
just to keep it a little bit more secure.
Now the piece is secure and the cutter heads
are going to cut the top of this board
parallel to this flat MDF piece
instead of the twisted bottom of this board.
But before sending it through the planer,
I just wanna talk about grain direction for a second.
If you look at the side of the board here,
you can see that the grain is running one way or the other.
So this is the direction that I want to feed my work piece
into the machine because it will cause a less tear out
because it's going with the grain.
If I would try to send it through going this way,
the cutter heads would then be going against the grain
causing tear out.
This might be hard on pieces where grain is running
in all different directions like this board over here.
Just try to find the direction
that most of the grain is going.
To set the cutter head, I raise it well above the work piece
and put the whole thing into the planer.
Then I lower the cutter head until I see
that the indicator has hit some material.
Then I do two full turns backwards to raise the cutter head.
I pull the jig and the work piece out.
Then I go back those full two rotations
to get back to that depth.
And then just to be safe from any high points,
I'll roll it back a quarter turn.
I don't do this every time that I use the planer
because I think it's easy to see the difference
between the rough wood and the freshly cut wood.
But for video's sake, I'll just scribble some marks
onto the wood here so you can see the progress
of how it gets cleaned up.
Now it's ready to go through.
You can see that the planer has started
to clean up all the high points.
And I'll just continue to lower the cutter head
with every pass until I see
all those scribble lines disappear.
So now the top of this board is parallel
with this MDF board.
And just a note, if you don't have a planer
and you have a router, you can do basically
the same thing with a router sled.
You just shim the board until it stops rocking
and then you can use the router to flatten the top face.
Let's test to see how flat this board is.
Easily comes up off of the hot glue.
If any of it gets stuck on the MDF,
you just chisel it right off.
Now flip it over onto that freshly planed side.
All right, no more rocking.
Awesome, I've just done exactly what a jointer would do
without using a jointer.
So the next step in the milling process,
if you have all the right tools,
would actually be to use a planer.
So you take the freshly jointed face
and you put that on the bed of the planer
and then the second face becomes parallel
to that first face.
So there's going to be nothing different in this step
if you have a planer.
So all you need to do is send the board through
using that freshly flattened surface on the bed.
The cutter heads are going to make this second face
parallel to the first one
just as a planer is supposed to do.
And boom, I have a board
that used to be all twisted and wonky
and now there are two faces
that are parallel to each other.
One thing to note here is that my jointer jig
is 48 inches long.
And this has been working for me
because I usually rough cut to length
before I start this milling process.
One time I needed a super long one
so I have actually this super long one here
that I only used once for a specific project
but this has been working for me
so just make yours the same size
as the typical projects that you work with.
Before moving on to step three of the milling process,
just a quick break to talk about
this week's sponsor, Policy Genius.
So tools like planers and jointers
help you turn rough lumber into square stock.
Without them, you'll either need to spend extra money
at the lumber yard buying surface lumber
or spend hours upon hours with a hand plane
making them flat and square.
No offense to anybody who enjoys doing that
but I personally like to take advantage
of modern tools that save me both time and money.
Which brings me to this week's sponsor, Policy Genius.
Another tool to help you save time and money.
So how can you do that?
Policy Genius compares America's top home
and auto insurance companies
so you can find the right plan to fit your needs.
Even if you already have insurance,
it might be worth it just to take a few quick moments
out of your day to see if you have the right plan for you.
Because Policy Genius has saved
its home and auto insurance customers
an average of about $1,000 a year.
All you have to do is answer a few quick questions
about yourself and your property
and Policy Genius will compare your current policy
with some others to make sure you're getting
the best coverage at the rate that works for you.
Besides for home and auto insurance,
Policy Genius also offers tools
to get you set up with life insurance
that fits your needs as well.
So if the experts at Policy Genius
find you a better deal than you currently have,
the best part is that they will do all the work
to get you switched for free.
So I think that that's a pretty cool tool
to help you save both time and money.
So head on over to policygenius.com
slash 3x3custom to shop the market and compare quotes.
All right, onto step three now.
The board now has two faces
that are flat and parallel to each other.
The next step would be to make one of the edges
square to those faces.
Right now, this is not even close to square.
You can see a big gap in there.
This maybe is easier this way.
There we go.
All right, so the right tool to do this
would be to use a jointer on the edge like this.
Pretend for a second that this is a jointer.
Like here would be the blade.
So if you have the face that was already flat
against a fence on the back
and then you run it along the jointer,
the blades over here are going to cut this edge
square to the face that's against the fence on the jointer.
So there are a few ways to do this
without having a jointer,
but you might be wondering why you can't just
rip the board like this through the table saw
and that will create straight edges.
Well, it's because the boards that you get rough
at the lumber yard, they don't have straight edges.
So you see the straight edge is rocking back and forth.
So if you would just run that
along the fence and your table saw,
the cut that the blade is going to make
is going to follow that curve.
So you're not going to create straight cuts
unless you have a straight reference against the fence.
One of the ways that I like to do this
is with a tapering jig because it has a straight edge
that gets referenced along the fence as you make a cut.
Or if it has a miter bar in it,
it just slides in the miter slot,
always creating one square edge.
So this is one of the most common questions that I get.
How do you know where to align your board
onto the tapering jig in order to make that square cut
since there's no square references on the board?
So the answer to that is that it doesn't matter at all
where you put the board.
You can set it up so that it cuts this board
into like some weird shape.
And this step is only making one edge square
to the two faces.
You're not making the whole board square just yet.
That's going to happen in step four.
So this board is a great example to show this to you guys
because of this weird corner over here
that needs to be cut away.
So I'm going to put this onto the tapering jig
just along where that like wonky edge is.
And it's going to make like a cut into this board
where the result is going to be a really weird
not square shape.
So what I'm looking for here is just an even amount
of overhang along the edge.
Has nothing to do with the squareness
on either side of the board.
I'm just cutting off all the bad parts that I don't want.
Then I could lock the fence into place
and then use the clamps to lock the board to the jig.
And now I just need to cut off that edge.
And just like that, this board has one square edge
but you can see that it's like a weird shape.
So the squareness of the whole board
doesn't matter at this point.
This tapering jig is 30 inches long.
So it works for most of the applications that I need it to
but sometimes I need to join a longer piece
and there's an even simpler way to do this.
So this piece of walnut is longer than the jig.
So it wouldn't be safe to use this to join that edge.
So what I would do is just take a scrap piece
of some plywood and I'll use that
as the reference against the fence.
And I'll just use some double-sided tape
to temporarily put that board onto that scrap.
Sometimes I'll use hot glue.
Also just depends what kind of mood I'm in.
And once again, this board doesn't have to be straight
or square to anything.
When you're aligning it up, you just want to make sure
that all the parts that you want to be cut off
are hanging off the edge.
Then same as before, just run it through the table saw
and this cut is referencing off of that straight edge
from the plywood.
Now that rough edge is all cut away.
You could just take this off of the plywood
and you have a freshly squared up edge.
And sometimes it might be hard to keep track
of all this stuff.
So I'll just make like a check
or some sort of marker symbol so that I know
that this is the freshly jointed squared edge.
Sometimes if the piece is really long, I use my track saw.
So this would just run along the edge here,
making one edge square to this top face.
This would be the same thing as just using a circular saw
with an edge guide.
And that's actually the way that I used to do it
before I got this.
You can also use a router table as a jointer.
I actually posted a video a really long time ago
on how to do this.
But basically just imagine that the router table
is like a jointer flipped on its edge.
So the fence over here is actually like the bed
of the jointer and you would set the outfeed fence
like offset it a little bit just to make room
for the amount that you're cutting off.
So it's actually a really cool process
and I'll add the link down below
if you're interested in learning more.
Another great way to get around not having a jointer
is to just use a straight edge
and a pattern bit in your router.
So if you take a known straight edge
like something man-made like plywood or MDF
and you double side tape that to a work piece
overhanging just slightly,
then the bearing on this bit is going to ride along
this straight edge creating one straight edge on your board.
Onto the last step here.
So the board has two faces
that are flat and parallel to each other
and it has one edge that is square to both of those faces.
And now the last step in the process
is to make that opposite edge square to the faces
and also parallel to that opposite edge
because if you look at the board here,
at the bottom, it's about four inches wide
and at the top, it's about three inches wide
because of that angled cut we did with the tapering jig.
Normally that difference isn't so drastic.
I just wanted to show you how in that third step
where you're just squaring up that first edge,
it doesn't matter if it's a straight cut at all,
either at the router table as a jointer
or using the pattern bit or any of the other methods
where you're using a straight edge against the fence.
The square edge that was cut in the third step
is now going to be against the fence.
So the cut that I'm doing now is going to do two things.
It's going to make this edge parallel
to the edge that's against the fence
and it's also going to make it square to the faces
because the blade is at 90 degrees.
Boom, square stock.
So that's basically how you get rough lumber
into square usable stock and now it's ready to be used.
Well, sort of.
So everything that I just did,
I milled it slightly oversized.
So like maybe like an eighth or a 16th,
really not important exactly how much,
just slightly oversized.
And the reason for that is because of moisture content.
So there's a ton of moisture still in this wood
and as you remove layers,
you're exposing the inner core of the wood,
which probably has more moisture than the outside.
So as that outside is going to dry off,
it might then kink or twist or bow or cupper
or something like that as you're using it.
So in order to prevent that,
after doing this whole process that I just showed you,
I then bring it inside my house
and I stack and sticker it overnight or for a few days
so that that top layer that I just milled dries out.
And then if it does move on me,
then I could just mill off that tiny little bit
and get it to its final dimension
and then it's ready to be used.
So I hope this was helpful
for all you guys who don't have jointers.
I think it's really cool
that even if you don't have the right tools,
there's always a jig or a workaround to get the same results.
While I hope to get a jointer one day
and I think it's going to make my life
just a little bit easier,
I think that these are great alternatives
if you don't have those tools.
So thank you guys so much for watching.
Thank you to Policy Genius for sponsoring this video
and I'll see you on the next one.
Before, I think I have to sneeze.
This straight edge is rocking.
Who's calling me?
