SMALL Cross-Cut Sled with ADJUSTABLE Fence, EXTENSION wing and BEVEL Feature!

D&P
34 followers
2 Video Views·Oct 24, 2022
I made a new crosscut sled.
It has an extension fence for repetitive cuts on long stock,
an adjustable fence for angled cuts,
and it also can cut longer bevels like for box parts.
The first step that I'm going to do is to make the fences.
I know that I want them to be about 3 3⁄8 tall,
so I will rip them a little bit wider than that
so that I can trim it after the glue dries.
I got that measurement from the stuff that I'm going to use.
This is the only thing for my old sled
that I'm going to keep, but what's really cool about it
is that it's totally adjustable for different height fences.
So I have two pieces for the front fence
and two pieces for the fence for the extension
and the back fence,
but I'm going to glue them up at the same time
using a level clamp to them to make sure
that they're completely straight and flat.
This is the piece that's left over from cutting the fence,
and I'm going to use that as the base.
So I followed my plans that I have on my website,
and I drew out some lines to cut away at the excess
to just, like, get rid of a little bit of the weight.
Now, the reason why I'm actually making this sled
a lot narrower than my last one
is because I don't plan on using this sled
for cross-cutting wide panels because I just got a new toy.
So I'm going to primarily use a track saw
as a way to cross-cut wide boards,
and since I got a new toy,
that's what I'm actually going to use
to cut off all these excess parts on the base.
Yeah, I'm going to need to get some dust collection for this.
That definitely took a ton of weight out of this base.
Next up, I want to put in the dados for the T-tracks
that are going to hold the hold-downs,
and in my last cross-cut sled video,
I used my table saw and did multiple passes,
totally regretted that decision,
and said in my next cross-cut sled
that I would use a router, so that's what I'm going to do.
I'm going to use my trim router
with this router edge guide that I made,
and the only caveat with this router edge guide
is that you always have to mark the center
of where you want to cut.
So I had to mark out where I wanted all the tracks to go.
Can you see that?
And then I had to mark in the center
of all those places where I want the tracks
so that I can line up the edge guide.
Next up is the runner,
and I've had luck in the past using this HDPE material.
It's like a plastic.
You can use extra cutting board material
and stuff like that.
The reason why I like using this
is because it's super stable,
and it won't expand or contract with the seasons.
I'll just measure the miter slot here
and set the fence to that width.
Now, the key to these holes is to drill the hole
wide enough that the screw totally fits through the hole,
because if the hole is smaller than the screw
and you start screwing it into the base,
the plastic is actually going to expand out this way,
and then these won't fit into your miter slot anymore.
Now I'll just use a countersink bit on all these holes.
Time to attach the guides onto the base.
So when I marked out everything before,
I made sure that the center of this front portion here
is in line with the blade,
and these T-track slots are not going to interfere
with the miter track slot.
So I'm going to align that front portion with the blade
so that it's in the center of over here,
and I'll adjust the fence just to reference
as I'm temporarily attaching the guides.
So I'm going to put some washers into here.
This will lift up the guides
so that it touches the bottom of the sled.
I just noticed that I actually had to cut two of these
because this material wasn't long enough,
but if you get material that's long enough,
you won't have to cut two.
Now I'll use some double-sided tape on here.
Bring that sled back.
I'll butt it up against the fence in front here.
Just pre-drill a little bit into that plywood,
and lock it down with screws.
I'm not going to over-tighten here.
Just cut this flush first.
Now I'll cut the T-track to size.
The T-tracks come with screws,
but they're too long to go into here
because of the depth of the dado.
So I'm just going to cut them down before installing them.
Now the T-tracks are in place,
and I'll use a Vix bit to pre-drill into the holes.
I'm actually also going to put in the T-tracks
with some five-minute epoxy
just to give it some more holding power
because these are kind of really small.
And the screws are really just there to hold down
while the epoxy dries.
While that epoxy sets up, I can unclamp the fences.
I added just a few more clamps
while you guys weren't looking.
All right, I'm going to go trim these up at the table saw.
Using that same 3 1⁄4-inch router bit from before,
I'm going to make the tracks in the top for the T-track,
and I'll just roughly center it.
Now I can install the T-track in the fence.
See how this piece juts out a little bit,
and it will help with alignment into the fence,
into the main fence.
Next, I'll cut the extension base to size,
and I can use the long part of the main base
to set the fence for that.
Now I need a way to connect the extension
to the main part of the sled,
and I thought of a few ways to do this.
I thought maybe to use dowels or something like that.
If I had a biscuit joiner, I would probably use that,
but instead, I'm going to use this slot cutting bit
on my router to create slots on both parts,
and then I'm going to make my own biscuit sort of things.
Now when I'm making the matching slot,
I just want to make sure that I'm referencing
like the same surface, so the top and the top.
That way, they'll be even.
And I'll do the same thing for the fence pieces.
All right, maybe I'll get lucky in here.
Find some material that fits.
Oh, nice.
Okay, that's a perfect fit.
All right, so I don't have to mill anything up for this.
Ooh, I just have to cut it to size.
Awesome.
And now I'll just glue the splines into place
on the extension part of the fence, not the main part.
Not going to use a lot of glue here
because I really don't want to squeeze out.
The pieces now fit together and align really well,
but I'm going to need a way to lock them into place
when I'm actually using it.
I thought maybe I would use this steel bar stock
as some sort of lock,
but I think that this piece of oak
is going to be strong enough,
so I'm going to go cut this up.
Now I will attach these onto the extension piece.
I'll go use some glue.
Yeah, I'll use some CA glue.
I actually considered making another groove
in the fence pieces so that these would lock into them,
but I'm not really sure if it's necessary.
So I'm just going to use some CA glue and screws.
Now I'll make sure that this is on a flat surface here
to make sure that the front is going to be completely level.
And I'll take my level again.
I'll put it on the bottom to make sure
that that bottom is completely flat and level.
Going to clamp it.
To make the locking mechanism,
I'm going to use these threaded inserts.
I'm going to be using these knobs to lock it in place,
so I'm just going to eyeball where they'll go
to make sure that they're not going
to bump into each other.
And I'll drill straight through these oak boards
and the fence using a stop collar
at the correct depth that I want.
I'll drop some CA glue in place.
Not actually sure if it's necessary.
And I'll use a bolt to get the threaded insert into place.
I'm adding a chamfer to the bottom front of the fences,
and this is going to collect dust
and will keep my cuts more accurate.
And I'll add a round over to all the edges
that I'm going to touch with my hands so it feels nice.
I'll put the back fence on first,
and this doesn't need to be really square or anything.
This is just holding the two halves of the sled together,
just keeping it a bit more stable.
Now I want to attach the front fence,
but I want to attach it while it's connected
to the extension.
That way, when I'm setting it for square,
the whole front fence is going to be set for square.
So I'll lock it into place,
and I'll clamp a level to the front of it
so that it stays completely straight while I'm attaching it.
I'll put the extension base into place.
Since there's only one screw in place,
the fence can pivot so you can square it up
to the cut line that you already made.
Once I'm happy with the position,
I'll clamp it down into place on the other side.
I changed my mind how I want to square up the fence.
So there was just too much deflection in this center area
when I was trying to do a test cut,
and it wouldn't give me an accurate reading
because when I was pushing along here,
there was too much bend
because these points are far away from each other,
and there's also this joint here,
and the level being in the way just was not a good idea.
So I'm going to take off the extension portion,
and I'm just going to square up
the main portion of the sled first,
and then I'll attach the extension piece
using the level clamped to the whole fence,
and then hopefully that will keep it nice and square.
All right, looks like it's square,
so I'll lock it down, avoiding the holes here,
that I don't run into that.
In the past, I've used the five-cut method
to calibrate my fence and make sure that it's square,
but I think I'm actually just going to cut
this long piece of plywood and check it with a square.
If it looks square, I'll just lock it down.
That is square enough for me,
so I'm going to go ahead
and lock down the rest of the fence.
Now I'll put on the extension base
and the extension fence, and I'll lock it down.
How cool is that?
So I'm going to test for square
with this long piece of plywood.
Let's see.
Looks good to me.
I'm so happy about this.
All right, next step is to cut the bevel.
The reason why I only use one miter track
on the bottom of the sled
was so that I can switch it to the other miter slot
and I can cut bevels on this end.
First, I'm going to raise the blade and set it to 45.
Just lower the blade a bit.
Now I'll just cut into the side of the fence.
Now I'll make the jig that's going to go
in these two T-slots over here,
and this is going to be an adjustable fence
so you can cut any angle you want.
So this fence can now be set to any angle that you need.
My most commonly used angles are 45 and 30,
so I'm going to cut a 45 on one end
and a 30 on the other end.
But you can actually cut four corners of this
if you flip it upside down,
and you can use all four corners
for the common angles that you normally use,
or you can just set it as you need it.
So I'm going to set this by using a triangle.
Once it's set, I'll lock it down and cut off the end.
And what's cool about this
is that once you cut the angle one time,
you can use that as a reference
for where to set it for the next time.
So all you would have to do is line up that 45-degree cut
or whatever angle cut that you need against the blade
and then lock it down
and you have the correct angle for your project.
I'll actually use it now to shape the blade guard
that I'm going to put it at the back of the fence.
I just want to make it a nicer shape,
so I'll clamp it down here and make some cuts.
Awesome.
So super excited about this.
The first feature that I'm going to test out
is the extension fence.
So the reason for the extension fence
is to make repetitive cuts on long pieces easier.
And it's pretty cool that this stop block
transitions back and forth from the extension
to the main part of the sled
because of the way that the T-track was installed.
So this stop block actually is a really cool feature
that I want to show you.
So let's say I want to cut this board,
let's say to 34 inches, all right?
So I'll set this 34 inches away from the curve
and what you can actually do is push it out
and then lock it into place.
Double check that that measurement is correct
before making any cuts, obviously.
Adjust it slightly.
Now it's set to cut the piece at 34 inches,
but I first want to square off one end.
So what I'll do is I'll flip the board onto its edge
and slide it underneath the stop block.
After squaring up that end, I can now flip the board over
and put it on its face, push it up against the stop block
and now cut it to the measurement that I want.
So this is really great for making multiple cuts
so you don't have to move the stop.
I really love this thing.
And one of the best features
is that there's zero deflection on it.
I'm sure some of you have experience
with stops like this one.
Not so cool for accuracy.
Speaking of accuracy,
this stop also has a micro adjust feature.
So let's say you cut your piece and it's slightly too long.
So all you have to do is unscrew this little knob
and adjust it ever so slightly
to get the correct measurement.
You can just guess the amount,
use feeler gauges or paper, whatever works for you.
Next, I'm gonna test out the bevel feature.
So I would use this when making boxes,
like wider pieces that need a 45 on the side of them.
So first I'll just cut this up into equal size pieces.
Using the stop block.
Now I'll swap it over to the other miter slot
and set the blade to 45.
I'll line up the piece on the edge of the sled here
and I'll adjust the stop block
so all the pieces are going to be the same
and cut all four pieces.
Now I can adjust the stop block
so that this edge is lined up with the cut line as well.
Oh, I could just do this one.
Yeah, let's do that.
And I'll cut all four parts.
Now the ultimate test.
Not too bad for my first attempt at this.
So this is great for making boxes and things like that.
But if I was cutting like shorter miters or angles,
I would use the adjustable fence feature.
I already showed you guys a little bit how this one works,
but let me just cut up four pieces to test how square it is.
I'll cut just one more piece and I'll use this as a stop.
Now I'll put this on the sled and I'll use this clamp.
Pull down this stop piece.
That way I can butt it up against that angle over there
and they'll all be the same measurement.
That's like perfect.
I am so excited with all the different things
that this sled can do.
Everything that you need to build this
can be found on Woodcraft's website
and I will link to everything that I use.
I'll also link to my website where there's a full article
and plans for you to download.
Oh, before I go, I don't know if you guys know this yet,
but the Builder's Challenge is actually going on right now.
It is a competition where people build furniture
to win prizes and it's a ton of fun.
So I'll drop a link to that down below.
And a huge thank you to Woodcraft
for making this awesome jig hardware kit.
They have a ton of other options for making jigs
and everything that you need in your workshop.
So thank you guys so much for watching
and I will see you on the next project.
The only caveat with this caveat,
caveat, how do you pronounce it?
Caveat.
Yeah, okay.
