Geometric Design Table | Woodworking

D&P
34 followers
19 Video ViewsยทOct 24, 2022
Whoo
Hey you what if I told you out of all the dining tables that I've built. This is the one that gave me the hardest time
crazy
Thank you to grizzly industrial for sponsoring this video and I'll discuss more on that later on
Well, are you ready to see how I built this table? What are you waiting for? Let's get this started. Let's go
We're gonna begin with the dining table top I start every project with the top and then I do the base
I've laid out six planks. This wood is cypress. It's uneven it teeters
I need to square it up mill it and get everything nice and flat and that's what we're about to do right now
Just finished milling these boards
Laid them out on the table. It turns out. I made a rookie mistake
I didn't check my joiner to make sure it was square all machinery gets out of square and you have to tweak it
Consistently on a daily basis. You can't rely on something to stay uniform to stay square too many things go
Nuts in a workshop and now I've noticed that I have all these open seams
Because my joiner was off by about a half a degree
rookie mistake
Now I got to spend some time fixing it
Look at the gaps between these planks. That is huge. And that is actually something I'm not used to
Before I move on to correcting my mistakes with these planks being uneven
I'm gonna mark this end grain. The reason I do this is
so that way I can I will be aware of
Which way the grain is oriented and
This will help dictate how each plank will go in reference to seasonal wood movement
I moved the planks around to where the green grain will be up down
Down
Kind of like a smile and a frown
This helps offset seasonal wood movement and helps prevent and minimize any warpage
Now I'm gonna correct my mistakes where the joiner was off square
I'm first gonna label the boards 1 2 3 so I can keep the proper orientation
Then I'm gonna make a couple of reference marks to know where they join
This is gonna be critical that I match these seams up
To get this nice and square
Yes
Just dance it out when you fix all your mistakes, it's the best way to go
All right. Let's glue this thing up
the younger version of myself just wants to grab all this lumber hump it on my shoulders and take it across the shop and
the older version of myself says
yo
Younger version. You're an idiot. Grab the shop cart and
Roll it across the shop
I'm gluing this table up into two sections
Basically two 20-inch panels that I can glue up run through the planer
Once they're cured and they're the right thickness
I will glue them completely up together and it will save time on sanding and milling
After you've glued up your planks
Get a rag wring it out get it damp not soaking wet and just clean up your glue mess
This will make life much easier on you whether you run this through a planer or whether you plan on sanding it
It just makes life much easier. So clean it up now
As you go abracadabra
Alakazoo make these boards appear for you
What?
Yeah
All right, let's do this again
boom
Now that these boards have all been laminated together cleaned up and ready to move on
I'm trying to decide how I'm gonna join them to make the table base
basically, I have two ways to go one mortise and tenon or
45s and dominoes
Still trying to decide let's figure it out together
Here's the block from the bandsaw and this is the tenon just toss this over your shoulder for good luck
I decided to go with a bridal joint
Instead of a mortise and tenon. I kind of lean toward bridal joints as being a stronger joint
Although mortise and tenon is incredibly strong. I like how a bridal joint goes all the way through
So now that I've got the tenons cut on these pieces
I need to go ahead and cut the opposite on these longer members so I can join the two together
Just finished on the bandsaw making a bunch of cuts or kerfs so I can chisel out
For the bridal joint on these two long members. It was pretty tricky, but I got it done
I figured it would be the easiest way to do it
The bad news is I actually cut one too many with the tenons
two of these sets
We're supposed to be like this
so once again
Another screw up on this build. I'm just messing everything up and having to redo so much work
Let's keep charging forward
It's always good before you do any chisel work to put another block here for a reference
It helps keep this nice and square if you didn't have this you could get at an angle
When you're chiseling, but this keeps it nice and flat and straight down
All right, so we have our two long members cut one here and one behind me
We have the short pieces with the tenons. We're gonna glue them up and
Clamp these bridal joints down. Let's get going
now it's time to
Put in the opposite piece
Let's take a moment to discuss today's sponsor grizzly industrial tools
They're a family-based company operating since 1983. They provide high quality woodworking and metalworking machinery
Working with grizzly industrial has been a dream of mine since I started and it's been a pleasure using their machinery ever since
It's high quality and it holds up to high standards if you're interested in any products
I'll have them linked in the description box below
Always want to take your square and double check if you get out of alignment
Obviously that makes the build
Much harder and in this case, I'm perfectly 90 degrees
I am right on the money if I wasn't I would put a couple of 90 degree clamp it
And we would clamp them down almost like building a cabinet carcass
But that's it on this guy. I have a couple of gaps here
That I'm gonna need to fix that. I got a little wonky with on the bandsaw
but super easy repairs, I
Just pulled this centerpiece off the clamps. I still have to clean it up sand it
Put some roundovers on it and put it back, but I'm dry fitting all these pieces now to make sure they're gonna fit well
Now you can see the table base coming together
The final two pieces on the ends that I just did a dry fit test on I'm gonna pull apart and
Glue them up and clamp it down and then we'll move on to the next step
Two bases were glued up and clamped up. I've got one here in front of me and one back there behind me
So I'm gonna D clamp this
Sand it and do any chiseling and adjustments that I need to make and then we'll move on to doing some
One inch roundovers on this. I love my roundovers and I'm looking forward to that part
These blocks were under clamping pressure for about 20 hours
I'm not expecting there to be too much cleanup involved as I pre sanded these box blocks before I glued them up
I've adjusted the depth on the router to the round over and it's a one inch round over
So let's go ahead and put this on now
Let's pre drill some holes and get ready to attach this base together
Putting a little extra clamping pressure so the piece won't shift when we get ready to screw it down
We're gonna be using lag screws, which are just an easy fastener for lag bolts. They work really well
They're amazing. I highly recommend them
All right. Let's repeat that step for the other side
Let's move the base around so it can overhang off the other end of the table
Installing leveling feet. I have a
Forstner bit with a stop collar on it
gonna switch out
to a
516
Switching out
to a wood tap
which is a quarter inch and
this is
Saving myself the step of using threaded inserts
Which is not necessary if you use this
Installing adjustable feet are just a high quality step in making sure your piece
Doesn't teeter when you get to a house. The floors are always on level and this just ensures that nothing will teeter
Now instead of using threaded inserts, I used wood taps to do my thread into the wood
I've actually tested this and it's stronger plus it's saving me money and an extra step
Let's flip the table base over
And then we'll have a little fine sanding to do
From not laying down a blanket rookie move
All right, let's do a final sand of 220 on this tabletop and
move on
All right tabletop is sanded. We're ready to put the stain on it. I'm using this reactive stain. That's gonna keep the wood naturally
With its wood tones with a hint of gray. I'm gonna use this applicator and get started
And this just toss over the shoulder for good luck
Like I said before this is a reactive stain meaning it's gonna change color tone slightly as it cures you can see the drying streaks
now
That's gonna leave behind a more of a natural wood tone with hints of gray
Getting ready to spray the sealer on the dining tabletop and I'm gonna be using the Fuji spray q5 platinum system
This thing is legit. Check this out. I
Just finished with my first coat of poly on the table. I've let it sit for one hour now
I'm gonna use 1500 grit sandpaper just to lightly go over it and get any dust or nips that may have fallen into it
Now using a tack cloth, I'm gonna wipe all the excess dust I just created from sanding
Alright, we just wrapped up the top. I applied six coats. It looks amazing
The finish came out exactly how I wanted it
And now I'm gonna show you how we're gonna attach the top to the base. So let's go on over and do that
Using a biscuit joiner. We're gonna go around and cut little slots that will use fasteners to attach to the top
The fasteners will be these Z clips
These help with seasonal wood movement. They will go into the slot like this
This will attach to the tabletop and it allows for wood movement to go back and forth
The top is just placed on the base. I'm gonna attach it with Z clips from the underneath
the Z clip just glows
directly into the slot and
Then zip a screw straight through
easy
If you guys enjoyed this video
well
don't forget to smash that subscribe button below and check out some of these videos over here or
Over here. And if you want to support what I do
Support the companies that support me
I'll have a link to all the products and tools used in this video in the description box below
All right guys get after it and I'll see you next time. Peace
