Edge Trimming Jig for Table Saw

DirtFarmerJay
310 followers
3 Video Views·Jul 19, 2013
Dirt Farmer Jay shows you how to build a simple edge trimming jig that has been used by woodworkers for many years. This jig allows you to trim off a standard amount of wood from your stock no matter how wide the stock is. Stocks of varying widths can be trimmed in succession without any adjustment to the fence position. Excellent way to trim wood with damaged edges or wild grain, without dramatically altering the dimension of the stock, by only removing a single saw blade width.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com with a shop tip today for those of you that
are woodworkers.
We have a little business in which we do a lot of processing of dimensional lumber such
as this.
This is a 2x6 fir piece of wood and it takes a lot of edge trimming.
You put that on a jointer and a jointer will do a great job.
The problem is it takes a lot of time to get it down to a basically straight edge and a
lot of the outside furniture that you may do may have grain changes in it, such as when
it encounters a knot like this right here, the grain coming off both sides of that knot
can cause a problem when you run it through a jointer.
If the grain's going uphill, so to speak, against the knives when you run it across
a jointer, it can lift that grain leading to what's called tearout.
On the other hand, as it goes past the other side, it's smooth and all's fine until you
hit a grain change again later.
A way to eliminate that and to speed up the process is to turn to the table saw.
The table saw's a great tool, put in with a nice rip blade in it.
Rip blade is blades that are meant to cut with the grain.
They have fewer teeth per inch around the rim diameter of the saw blade.
The set in the saw blade is set in such a way to shear off the wood fiber and leave
it smooth along the edge, and you use this to your advantage in removing the edge of
the wood.
Now if I wanted to just use the standard fence right here on the saw and adjust it back and
forth every time I wanted to run a piece of wood through, that'd do a lot of setup to
get it done.
Instead, let's do something easier.
Let's set the amount of wood that's going to be removed each time while supporting the
work piece, and then put the piece of wood on this side of the cut so it doesn't matter
whether it's a little wider or a little narrower.
It's always going to trim off the same amount along the edge.
Now just a disclaimer here, just to be sure, remember woodworking is inherently dangerous.
You can see I have safety goggles or glasses on with my side shields, and I am very careful
about what I do when I'm around the saw, and I recommend that you do the same.
This is at your own risk.
Work safely as Dirt Farmer Jay does.
Now on to the tip here.
To get the blade in the saw to cut dependably where it needs to go each time to remove a
predetermined amount of wood off the edge, you need a little jig.
And I made a jig like this.
This is just an auxiliary fence that gets clamped onto the edge of the saw of the fence
here.
You'll notice that on the back edge right here, there is a stop block that's been affixed.
And what that does is it hooks on the back edge of the fence and pre-positions where
this is going to go.
It doesn't sit back too far, it doesn't come too far forward.
It will always register in the same place and make the jig easier to use.
Now the second thing you need to do is to affix this to the saw fence in some way.
Now you can use speed clamps, you can use woodworker's clamps.
I like these little clamps.
These happen to be sold by Rockler.
You can find them at rockler.com, R-O-C-K-L-E-R dot com.
These have an adjustable distance in here.
And what you simply do is I've pre-drilled a hole in the edge, top edge of the fence
as you can see right there and down here as well.
Oh, by the way, there's also a hole drilled here.
I have an area in my shop where I just hang all these types of things, keep them out of
the way and keep them handy every time I need them.
I just go over and grab it and use it.
So putting this back here, I'm going to use a registration block, put this down on the
table saw.
This is going to fit right into the hole here as you can see just like that.
One up on the front edge as well.
And the last time I used this, I screwed it down a little tight so I need to open it.
You can see they're sitting there like that.
And then you simply go ahead and moderately tighten them.
No need to really wrench them down.
You're simply firmly attaching to the fence.
If you over-tighten them too, they're going to distort slightly.
You don't need to do that.
Now you can see it's firmly affixed here.
Now, I'll show you this in a close-up photo here now, but one of the things that makes
this work is the distance in front or the distance that the fence is set to the side
of the blade is exactly the width of the saw blade itself as seen right here.
Here's the saw blade.
In front of the saw blade in this area here, the fence is riding on the inside edge of
the saw teeth.
On the backside, there is a piece of, in this case, hardwood that's been put right here
that is the same thickness as the saw blade.
Therefore, this part of the fence in the front is equal or in plane with the inside edge
of the saw, and the area in back of the saw blade is as thick or is in plane with the
outside edge.
The reason for that, as we run the wood through the saw, it's going to remove one thickness
of the saw blade.
As it passes the saw blade, it's got to be supported.
Otherwise, the piece of wood is going to dive on the back and dish out the piece of wood.
As this piece of wood passes the saw blade, once it gets under the back part, it's supported
equally.
As long as I keep this block of wood up against here, and this will work with longer pieces
as well with an outfeed support table, which I don't have for the short block installed
for this video, but as long as I keep it flat to this outside fence, it'll remove this very
nicely.
Now, I want you to just see here, we're just going to show you.
Right here, you can see that this has a knot on the edge.
This would be a perfect piece for an outdoor piece of furniture.
We build a lot of bunk beds and we grind out the edges of these to make them nice for the
little hands and feet that climb on them, but I don't want to run that over a jointer
for the reasons I mentioned earlier because simply what I'm going to do is get a lot of
tear out.
So, what are we going to do?
We're going to run it through the saw and I'm going to show you the results.
First thing I need to do after I've installed this is make sure this is adjusted back and
forth.
In this particular case, it looks like it's right there.
The back edge is in plane with the table, or excuse me, with the blade.
The front face of the auxiliary fence is on the outside plane of the saw.
Now, I've raised the blade here, which I've done already to make sure that it clears the
thickness here and again, work safely, you're going to keep your hands away from the edge
here.
Let's go ahead and turn on the saw here.
We'll get the saw up to speed.
We're going to simply butt this up against the block right here and we'll run it through.
Right now, it's removing one width of a saw blade and as it passes, it's being supported
on the back edge.
Now, I'm just going to show you the results on this very quickly to see why this is such
a great way to do this.
Do you see how smooth that is?
Beautifully smooth.
I can grind out that knot.
Let's just look at this one.
I'm going to come close to the camera here, just let you see right there all that furry
wood and everything that's on there.
Let's do a pass on the saw and see what happens.
All right, here we go.
Again, taking on one width of the saw blade, back edge is supported, that passes everything.
Let me bring it over to you.
Same block of wood.
Look at the difference here.
Do you see there?
Just very, very nice.
I hope you found this tip to be very helpful to you.
If you liked it, please like the video on our YouTube channel.
Better yet, subscribe so we can send you these great tips from time to time.
If you have a comment or a question, an insight you'd like to offer to us or to the other
people that subscribe to our channel, feel free to do that in our comment section.
Until the next time, I'm Dirt Farmer Jay from DirtFarmerJay.com.
