How to Make a Scroll Base Console Table | Part 1

D&P
34 followers
8 Video Views·Oct 24, 2022
In this video, I'm gonna teach you guys
how to do my signature scroll-based console table.
I'll have links in the description box
for the templates and any of the tools
and products I used in this video.
Let's begin with making the template.
First step is I'm gonna go to my site
and print off my scroll-based design.
After you print the template out,
you're gonna wanna use this quick-drying spray adhesive.
I'm just gonna glue this on in the same pattern
that I printed it out on a quarter-inch sheet of plywood.
It's pretty simple.
Just line up the lines, spray the glue,
and stick it on the board.
After that's all done,
I'm gonna take it to the bandsaw here,
and I'm just gonna cut it all out
and then sand the edges to make them smooth.
This will now be my hard copy for the scroll-based template.
I will drill a hole in it
and hang it on my wall in the shop.
The good thing about making a hard copy
is now you'll have this template
for every future build that you make using this scroll-based.
I pride myself on coming up
with a lot of different templates and designs.
As you can see, this is just a few.
But moving on, we're gonna also do the base foot
for this scroll-based console table.
So same steps apply.
I'm just gonna spray the adhesive,
stick it on this board,
and take it to the bandsaw and cut it out.
And then I'll have the base foot and the scroll.
Now that we're finishing up with making our templates,
it's time to go to the lumber area and choose the lumber.
I'm choosing reclaimed poplar for this project.
Go ahead and start with the miter station,
turn on the dust collection,
and we're gonna start cutting the boards
for the base feet for this table first.
Now that the base feet lumber
have all been cut to rough dimensions,
each one of these planks
basically takes up two parts of the foot.
It's easier to run through the joiner and the planer
if you have a little bit longer board.
So here we go.
When doing the milling process,
I always start with the face grain
and then go over to the end grain.
After that is done on two sides,
I will then take the boards to the planer
and plane the parallel edges.
Now let's make our final cuts for those base feet
before we get ready to glue them up.
I'm using Titebond II for the glue-up of these table feet.
The lamination process can be slightly therapeutic.
I kind of enjoy it.
Just line up all the planks,
take two away, and glue it all up.
Be sure to cover all the edges.
You don't wanna leave any open voids in these boards.
Now let's simply clamp them up.
This is part of the glue-up process,
and we'll be done with this step.
When you're working on multiple projects at once
and doing a glue-up,
always make sure you time stamp your lumber
after the glue-up.
That way you can have sufficient time on the glue-up
before you remove the clamps.
Moving on, we're now cutting the boards
for the scroll column of the base.
Time to cut these to rough dimensions
and do the same milling process.
We're moving right along now.
We're already on the glue-up stage of the scroll base.
We're gonna let this sit for about two and a half hours,
remove the clamps,
and then we're moving on to the next step.
The scroll base is only two-dimensional,
unlike most of my table bases that I do
that are four-dimensional.
This, we only need to square up one side,
use my handy-dandy square
to get the dimensions of the length cut,
and we'll run it through the bandsaw
and make sure we get a nice square cut.
We've now cut the ends of the blocks.
I'm just gonna put my square on there now
and check for proper squareness.
This is pretty close to accurate.
I was just a little bit off in the center area.
I'm doing a little markings,
and I'm just gonna take my finger plane
and plane those areas off.
Now we're all square.
We're gonna run it through the table saw
and get the parallel edge on the other side.
Now that we got that done,
I'm just gonna take my card scraper
and make a few little adjustments as I'm squaring it up
and just making sure it's perfect.
This is the fun part.
Let's just trace out the outline
of the template we made onto this block.
Just be sure to take your square
and line up the back and the bottom to the block,
so that way the base will be accurate.
Just a side note, I love using this pencil.
This is an architectural drafting pencil
with nine millimeter lead,
so it doesn't break often like typical mechanical pencils.
Really awesome.
I hate going to the pencil sharpener over and over.
Just thought I would add that in there.
But let's go on over to the bandsaw
and start scrolling this out.
Now it is important at some point
to make a few relief cuts,
and you'll see that here in this process.
It just keeps the blade from snagging
and keeps you moving along much more fast.
All right, so that wasn't so bad, was it?
We got that scroll cut out.
Now it's time to move on to the second block.
And then we're gonna go to the feet.
All right, moving on to the blocks for the feet.
They're already been glued up and milled,
and they're ready to be traced on.
So I'm taking my template
and repeating the process just like the scroll.
We're gonna do it to both of these blocks,
take it to the bandsaw, and carve them out.
I consider the scroll base and this base foot
to be some of the simplest I do,
considering they're two-dimensional.
Anytime it's a two-dimensional base, it's easy peasy.
All right, so we got the base feet cut out,
and we got the scrolls cut out.
Now we're gonna take them over to the shaper,
and we're just gonna use a quarter-inch roundover bit.
And we're just gonna round out all the edges here
just to make them soft and subtle to the touch.
All right, guys, as this video's getting ready
to come to a close, I hope you enjoyed it.
The second video in this series will come out next week,
and that'll be about attaching these bases
and moving on to the second stage in this table build.
As always, thanks for coming back,
and I hope you enjoyed it.
Peace.
