Hey folks, welcome to Nomad Boat Building. We're picking up where we left off on the Poulsbo Boat Project.
In the last episode, I fitted and steam bent the longitudinal members that will become the inwales and thwart risers. This time, it's time to glue everything up.
I'm using epoxy to laminate the inwales and thwart risers into strong, rigid structures that will become an important part of the boat. I'll show you how I prepare the surfaces, use two-part bonding, choose between different types of clamps, and use polymer nails to hold the laminations in position while the epoxy cures.
I'm using WEST SYSTEM 105 Resin with 205 Fast Hardener for this glue-up. The two-part bonding technique involves wetting out the wood with unthickened epoxy first, followed by thickened epoxy to create the structural joint.
The Poulsbo Boat is a modern cedar-strip version of a 1950s-era sport fishing boat originally built by Roland Young in the Poulsbo, Washington area. The original was built using traditional carvel plank construction; this version is being built with cedar strip construction and fibreglassed inside and out.
There is one more tricky piece to add before this stage is finished, and I'll tackle that in the next episode.
Follow the complete build as the boat takes shape, from the building jig and backbone through planking, fibreglassing and finishing.
CHAPTERS
0:00 Introduction 0:31 Time to glue up 0:39 Preparing the blocking 1:02 Protecting the moulds 1:27 Why I'm willing to cut the moulds out 2:04 Preparing the epoxy surfaces 2:27 WEST SYSTEM 105/205 epoxy 3:00 Two-part bonding explained 4:18 Epoxy working time 5:06 Fine-tuning the clamps 5:53 Choosing the right clamps 6:41 Green state after the first glue-up 7:06 Starting the inwale lamination 7:22 Using polymer nails 9:00 Fitting the inwale 10:29 Mixing the epoxy 11:36 Wetting out the Douglas-fir 12:01 Preventing epoxy starvation 12:51 Why I like heavily laminated shears 13:24 A design problem I'll reveal later 14:21 Thickening the epoxy 14:48 Planning the four-stage glue-up 16:07 Adding alignment blocks 17:09 Getting the first lamination in place 18:33 Using polymer nails 20:00 Starting the second layer 21:26 Getting systematic with the clamps 22:58 Cleaning up the squeeze-out 23:34 Epoxy on a big boat 25:04 The inwales and thwart risers are glued up 25:13 What's coming next
This video from Nomad Boatbuilding demonstrates the glue-up process for the inwales and thwart risers of a Poulsbo sport fishing boat. It highlights the use of cedar strip construction and specific epoxy bonding techniques to ensure structural integrity, while offering practical advice on clamping, lamination, and workshop management.
Hey folks, welcome to Nomad Boatbuilding. We're picking up where we left off on the
Poulsbo boat project. The Poulsbo boat was a popular sport fishing boat built by Ronald Young
in the Poulsbo, Washington area. Ronald built his using traditional carvel planked construction.
We're building ours using a modern cedar strip construction, fiberglassed inside and out.
In our last episode, we fitted and steam bent all the longitudinal members to make up the inwales
and thwart risers. Today we're going to glue those up.
It's time to do some glue up. So I've done some blocking at the
stem to hold the ends of my laminations and it took a little more time to do some better blocking
back here at the transom to get the angles all correct. I've added some little angle brackets
to hold the thwart riser in so I don't need clamps to hold the primary portion in while
I get the secondary portion on top of that. I just want to go over my mold to make sure I've
got tape on all the spots that might get glued onto. There's a few spots that we've kind of
worked away at as we've been fitting these guys so I'm just going to make sure they're protected
before I start slapping glue everywhere. I know some of you thinking that we can't pull these
molds out because these things are all going to capture it but that's okay because I'm fully
comfortable with the idea of just chopping these molds out of here if I have to. They're temporary
because we won't be building this boat again and I know that because I never get to build the same
boat twice and if I were to build it again I'd probably come up with something I wanted to do
a little bit differently or use a slightly modified set of lines and so I'd probably
start again from scratch. Okay that'd be a terrible idea to just give this guy a little bit of a scuff
unlike some adhesives like PVA glues which like a really smooth surface to bond to, epoxy prefers a
very rough surface to bond to. We like to give it what we call tooth and so a good scuff with 80 grit
sandpaper is always a good idea. That's good. So this glue-up is fairly simple and as such I can
get away with using the West Systems 105 resin and the 205 fast hardener. It's a cool day.
All these are going to pop right into place and once they're in place I've got plenty of time to
get them clamped without worrying about the epoxy kicking off. So I'm going to use two-part bonding
as is my usual practice. Two-part bonding means you prime both surfaces with an unthickened epoxy
and then use a thickened epoxy to create a structural joint. So I'm going to wet out both
sides of the boat at the same time because I think I'm going to have plenty of time here
to get these glue-ups done. One way to think about two-part bonding is because I'm putting
on this thin layer of epoxy to essentially prime the surfaces I don't have to worry too much about
them kicking off because they don't really have any volume to them and especially because my
secondary part that I can that I have to put on here is not going to have any trouble getting
it to fit. So there's very little time constraint on getting this all in place and clamped up.
The main reason for that is I'm going to be coming back with a thickened epoxy to
fill in between the joints. These saturation coats are there to absorb into the surface of the wood
and so if they've got a little extra time to do that before pressure is put on them that's great.
Under normal room temperature conditions we have a good solid 20 minutes of working time
and by that I mean we've got easily 20 minutes before we have to worry about it getting to a
starting to kick off so no trouble getting all this together in time. It'll probably be closer
to half an hour 40 minutes before we should generally not be messing around with the joint
that is trying to manipulate it. If I mix a fresh batch of thickened epoxy it's the time that that
batch is mixed that is going to govern how much time I have to work. This is one reason that I
prefer to mix my epoxy in smaller batches just enough for one task and then mix another batch
for the next task and that just gives me more working time overall and more peace of mind.
Now I'm going to come back and do a little more fine work on the clamping here
after I've gotten this sort of tacked in place. A few spots that need some more robust clamps like
right here. Okay there we go pressure is off. Now I'll just kind of go over this
more clamps clamp pads and just get it all kind of dialed in. Quick grip clamps are really useful
in the workshop but they really can't replace the amount of power and dexterity that you get
from a c-clamp or an f-body clamp. Quick grip clamps are just a little bit mushy like it's
hard to get a lot of pressure from them but it's also a little bit difficult to get them to sit
just perfectly so whereas with the clamps that have screws that engage you can have a little
more finesse shall we say. These are still pretty gooey. It's been about three hours
since I did this but that's like we call this the green state where it's rubbery kicking off
but not definitely not cured but that's probably sticky enough I could get away with
removing quite a few of the clamps. I need to now glue up the end wale.
Most of that comes together pretty easily but I will need to add clamps near the end of it so
I'll start with just like spring clamps to get myself started.
We're going to use the pin nailer on here with the with the plastic nails and then after that's
all tacked together then we'll come back and we'll grab a handful of these guys to sort of
solidify it in a few spots and I might just swap out these for some other clamps that I have on
hand. These four inch c clamps I particularly like for doing lamination jobs because they've got a
really nice big broad foot on them a really good quality screw on them like it's really smooth
and they just they hang on beautifully. I wish I'd bought more of these when I had the chance way
back in the day. I got them pretty cheap back then. I should have should have doubled my purchase but
oh well. Okay, let's get on to it. Okay, so let's see. First step, let's get these off of here.
Clear a little space.
Uh, you know what?
There's the last two. Ouch. Don't do that.
Train wreck. I don't want the orientation of these to get all buggered up. There we go.
And now these two. I can tell you right now I probably should have done a little shear
correction on this. Shear correction is where we take the fact that it's a fat
bluff bad boat and we add a little more shear to it in order to make it look like the bow isn't
drooping but this has got a ton of shear to start with so well maybe I don't need it. Hard to judge.
All right, everything here is looking good
and it is. A little bit of tape needed on there. Tape on there and there.
I shouldn't have taped all these up before I did all the fitting work. Buggered up my whole tape
job. Okay, that's out of the way. All right, let's mix up some goop.
Let me think. What did I need before? One. Two. I need at least three
shots to get it wetted out. Then I think a fourth to thicken it up. Get the first layer on.
Do four. We'll do four.
Okay, I've got to turn on the compressor. I'll unplug this thing at night because when I don't
it goes off in the middle of the night. My bedroom's right above that feast and I'm running
down here with my ghoulies hanging out to turn that thing off. No one needs that picture in their
head. Once again, I'm using a two-part bonding process and I'm making a point of applying epoxy
to the more absorbent surface first so it has more time to soak in before we bring the joint
together. In this case, that's the Douglas fir layer of the inwales. Gluey, gluey, gluey.
Where's Kate when I need her? I have her helping me with this glue up. Now the point of a two-part
glue up is to prevent starvation of the joint and that's a phenomenon where you either haven't put
enough glue into the joint or the surfaces you're applying the glue to are so absorbent that they
suck the bulk of the glue out of the joint and there's not enough left behind to create a good
bond. This is one reason when we're working with epoxy that we try not to over clamp things. We
don't want to squeeze it so tight that we squeeze all the glue out of the joint. While some adhesives
require clamping pressure to achieve full strength, epoxy does not and that's one of its advantages.
Seems like now this is the second or third. Man, I've been doing a lot of... a lot of my boats got
these... I find myself doing these very heavily laminated shears on them, which is not a bad
thing. That's actually a really good thing because then you get a boat that's like very robust
in the area where it's normally least robust. So that's one of the reasons I like putting caps on
them as well. It covers up all the ingrain of the... or all the laminations that you've put into it.
That way I can build boats that don't require like a lot of quarter knees and hanging knees
and things like that because they're already really stiff in their shape. So I realized I did something
dumb when I was designing this transom. I didn't even click on it until I was installing these
in-whales or fitting these in-whales and I realized maybe, you know what, we're going to
save that as a spoiler for later on. When we get to the trimming out stage I'll point out what I screwed
up. This whole series is turning into a one long series of screw-ups on my part. Things I got wrong,
things I overlooked, things that just went sideways on me. I'll thicken up this. So I think I want to
make this slightly stiffer so it doesn't drip off of the in-whales.
There we go. That'll be good. That's kind of gloopy. This colloidal silica is always a little challenging
to get the little lumps worked out of it. Probably not a big deal if you stay whole. They probably
saturate inside the joint once you're starting to clamp it all up and everything.
All right, so the trick here is I got to do this glue up in four stages because each layer has
got two strips, right? So I'm going to staple the first strip on and then the next one above it.
I'm going to put a little goop in between the two. I didn't bother wetting out between the two because
it's just one more operation too many, frankly. Okay, and clean, gun.
Actually, you know what I'm going to do?
Quickly, quickly, I want some little blocking on this thing. I hope I've done with all my...
Oh my god, I've used up all those blocks there. Okay, blocking, blocking. I don't have a ton of
stuff that's taped up. What I want is just a few extra blocks
to help align these things too. This might be a dumb idea. It felt like a good idea when I did it
when I didn't have them before and I was thinking I should have them. We'll see.
First one. Slip it in.
Get it tangled up with everything in the shop that you can find.
So ideally, I just want to get it all kind of pinned into place with some clamps. Get it nice
and flush on the bottom. It's a nice thing about light laminations. You can use stuff like spring
clamps quite effectively. Great. All right, it's all flushed up. This is a perfect application for
polymer nails. Now, these nails are made by a company called Raptor and they do require a
proprietary gun. However, I've tried them in my Porter Cable 18 gauge nailer and they did work.
So you could always try picking up a box and giving it a shot with whatever nailer you have
and see if they function. This isn't sponsored but I'll put a link to Raptor down in the description
and I'll put a link to a Canadian source for Raptor products in the description as well.
Okay, that takes care of the first layer. Now I just need to repeat that whole process and get
the second layer on. Okay, last one. Come on. Get in there. Get in there. Get in there.
There we go. There we go. Good. Good. Good. Excellent. Get it. Get it. You can do it.
Whoo.
Just sort of do this in sections, you know. Clamped.
Could be a little more systematic this time. Not for any good reason other than to be systematic.
Makes you feel like you're working pro. I am getting hot and tired. Too much stuff. Too much
stuff. There. Now, we'll use the clamps and my putty knife. I'll squeeze up all,
scrape up all the goo and then we're going to re-clamp. You know, as great as epoxy is,
you get these people building like 50 foot long all composite boats. I don't know how you can
stand it. I couldn't stand gloving up all the time like that. So now we do a quick mop down and then
throw more clamps on. The final clamp up.
There's going to be more squeeze out to clean up after it's all cured, but that's
for another day. For now, I just want it looking sort of tidy.
All right, our throat risers and our in-whales are glued up,
but there's one more little piece that we need to add. It's going to be a bit tricky though,
and so I'm going to save that for the next episode and I'm going to show you how I use
mock-ups to try and solve problems. So I hope you join me for that. I want to thank you all
for watching. I especially want to thank all my followers on Patreon who make these videos
possible. So if you'd like to support the channel, please consider joining me on Patreon.
Links in the corner or down in the description. All right folks, catch you next time. Ciao for now.