Building a hickory self bow is a great way to get into the world of bow building and primitive archery. Hickory is a great bow wood for beginners because it's easy to find, tough as nails, and you don't have to wait for it to dry before starting to work on the bow. In this video we'll be building a short flat bow in the paddle bow design. It will bend through the handle and draw 45lbs at 26 inches. Even if you never plan on bowhunting, knowing how to build a primitive bow is a valuable and fun survival skill. And hickory is a great wood to use in a primitive survival situation.
Don't forget to subscribe to the channel. We're uploading a new video each week that features one of the following topics: archery, bow hunting, bow building, survival skills, bushcraft, self reliance, primitive skills, primitive bows, hunting, camping, fishing, and a lot more!
Big thanks to our partners who help support these videos!
AI Generated·May contain errors
Video Summary
AI Generated
This video demonstrates the process of crafting a paddle-shaped \"D-Bow\" from a hickory log. The creator guides the viewer through the initial splitting of the wood, shaping the profile, tillering for a 45lb draw weight, and finishing the bow with a protective oil seal.
All right guys, in this video,
we're gonna be making a little paddle-shaped D-Bow
out of hickory.
So stick around.
So today we're gonna be working
on a little hickory flat bow.
Now I've got a quarter of a hickory log here.
This thing's just a little over 60 inches
and about six inches wide.
And so the first thing that I'm gonna do
is just split this thing in half
and then we can start reducing it and making a bow.
All right, so before we get started on this bow,
I wanna go over just the very basic tools
that you're gonna need.
So we're primarily gonna be using a draw knife.
We'll use a farrier's rasp, it's got a rough side on it.
We will use a little compass.
This is not absolutely necessary, but it will come in handy.
And we'll also be using some card scrapers.
Now this stave's a little bit shorter
than the bows that I typically make.
And so what we're gonna do is end up making a D-Bow,
a bow that's bending through the handle.
So this bow that we're gonna make today
is not gonna have a stiff riser
like some of the other bows
that you might've seen me make.
All right, so that's split super clean.
I like that.
That'll make two really nice little bows.
So the first thing that I wanna do
is go ahead and clean up one side.
We're gonna use this clean side to scribe a line
so that we can end up with parallel sides
and then we'll cut the other side to match.
Now, if you look at this stave, the way it's split,
this thing is kind of pie wedge-shaped.
So we've got the back, which is the outside of the tree.
It's gonna be right here.
And then the side kind of comes down like this.
What I wanna create is more of a 90 degree angle here.
And so I'm gonna take my draw knife.
I'm gonna take this ridge off right here
and I'm gonna try to square the side up
with the back of the bow.
So if you're into bow building
or primitive or traditional bow hunting,
go ahead and subscribe to the channel
because we're putting out a new video every Thursday.
And if you're looking for more in-depth
bow building instruction,
you might wanna go check out my Patreon site.
There's loads of videos over there.
And then there's also my book and my DVD set
that's available on my website.
All right, so now we've got our top edge
that we were working on,
about a 90 to the back of the bow,
which is gonna be where the outside of the tree was.
So I wanna take just a minute
to talk about the back of the bow.
This is the part of the bow that faces away from you
when you're holding and shooting the bow.
Now, if you've watched any of my other videos
on building Osage orange bows,
you'll know that I remove the bark, the sapwood,
and then I follow or expose along the back
one unbroken yearly growth ring.
Now, with most of the whitewoods,
that's not really the way that you're gonna do,
that's not the way that you're gonna prepare the back.
For most whitewoods, all you've got to do
is remove the bark and the cambium.
And on this particular piece of wood,
that's exactly what was done.
And this was done before I ever got the wood.
You can actually see these little brown spots,
that's just little remnants of the cambium,
which is the layer between the wood and the bark
that was left on this bow.
And that's not gonna cause any problem at all.
And so with this bow, the back is already prepared.
There's no need to chase a ring or any of that stuff.
So we can just move on, we can skip that step
and move on with the process.
All right, so now that we've got this side squared up,
I'm gonna use my pencil and my compass here
to scribe a line inside the stave here
that parallels this side that we just cleaned up.
And for this bow, I'm gonna make it about two inches wide.
It's a fairly flat stave,
meaning that it doesn't have a lot of crown to it.
If it was a higher crown stave
or came from a smaller diameter tree,
I might make it a little bit narrower.
Now to do this, you don't have to have a compass.
You can do this with just your fingers.
And I show how to do that
on some of my older bow building videos.
But these compasses, they're not very expensive
and they really come in handy
when you use it several times
for several different things during this build.
All right, so this line is gonna be a little bit difficult
to see on this camera because it's so fine,
but you might be able to see it.
Now I'm gonna take my draw knife
and I'm gonna bring this side into this line.
And then we're gonna have, when I get done with that,
we're gonna end up with a stave that's perfectly parallel.
And then once we get that done,
we'll start bringing these tips in
and tapering the tips out.
Again, when I'm doing this,
I'm gonna try as best I can to maintain
about a 90 degree from the back of the bow.
If you're working with a stave that's got some crown to it,
you're just gonna have to average that out a little bit.
So I've got the edges down pretty well parallel.
Now, because this thing's gonna be a D-bow,
a bend through the handle bow,
I don't need all this stuff on the belly side.
And so I'm just gonna go ahead and knock that off
to make this thing a little bit easier
to maneuver and handle.
Big knot there.
There we go.
Not really advisable to use your draw knife in that way,
but proceed at your own risk.
All right, so this is a pretty straight stave,
really straight actually.
And so I'm just gonna lay this thing out on a string line.
You could do this with a chalk line, but I don't have one.
So I'm just gonna use some leftover bow string material
and put it on there and make some marks.
A chalk line would be really the best way to do this.
You just put it on there and pop a line.
So I think with this one,
I'm gonna make kind of a paddle shaped bow,
which is kind of an hourglass shape.
So it gets narrow at the handle, mid limb,
it's the widest and it tapers down to pretty fine knocks.
So I've got the handle here laid out
about maybe an inch and an eighth or so wide.
We're gonna come and make a nice slow taper out
or slow flare out to the mid limb.
And then it's gonna narrow back down
to half inch knocks down here.
So from the center of the bow, I'm gonna measure,
let's see, we'll go out about 10 inches or so.
And then same on this side.
So I don't usually like to use a Sharpie on whitewoods
because it soaks into the wood,
but this pencil is kind of hard to show up on the camera.
So I'm gonna go ahead and use it.
I use it on Osage because Osage is so dense
that the Sharpie marks don't really stay.
And so now I'm just gonna take these edges,
pretty close to those lines.
You know what?
I'm gonna cheat a little bit.
Got a power plane over here
that'll make short work of that.
All right, so I've got the rough side profile,
got about 15 millimeters or so deep here,
35 here, and then it just comes from this fade,
which is kind of a fade and just slopes up.
This is just gonna be a rough side profile.
Once we start tillering, all this stuff's gonna change.
So I'm gonna take it right on down to this now.
I'm starting to get somewhere.
I'm gonna round these sharp edges off on the back.
I think that's gonna make a pretty cool looking little bow.
Just gonna throw it up on the tillering rack
and see what it looks like.
It's like the left-hand limb's a little stiffer,
but overall, it looks pretty doggone good.
Right in here, it's a little stiff.
Take a little bit off this, put it back up there,
and then we can probably cut some nocks into it.
All right, pretty stiff.
Looks pretty even, though.
I'm gonna take a little bit more off and restring it.
It's fairly even side to side.
I'm just gonna keep track of the number of scrapes
and make the same number of scrapes on either side,
maybe 30 or 40 per side.
This limb here, a little stiffer.
Left limb is still stiff.
It's just not rounding out like this one.
Need to take a little more off right in here.
Still pretty stiff right out in there.
Starting to even out a little bit.
This handle's not really flexing any at all,
so I'm gonna take a little off that too.
That's 26 inches right there, so that's 45 pounds at 26.
That'll be about right.
I can feel it flexing in my hand just a tiny little bit.
Let's go shoot this thing.
So this little bow turned out really nice.
It's 45 pounds at 26 inches.
I could probably stretch it to 28 inches,
but it's kinda short, and so I'm just gonna leave it
at a short draw like this.
So with this bow, I'm not gonna cut an arrow shelf
into it or anything like that.
I'm just gonna shoot it off my knuckle,
more of a primitive style bow.
So I really like hickory as a beginner's bow wood
for a couple of different reasons.
Number one is it's very readily available.
This stuff grows from Florida to New York State
and everywhere in between.
It's something that most people,
if you have access to some woods,
most people can get their hands on it.
And another reason is that it's a very tough wood.
You can make a lot of mistakes on this
and still end up with a bow.
And then the third reason is you can cut it green
and you can get started on a bow immediately.
And so there's no need to wait a year, two years
for this stuff to dry like you would have to with Osage.
You can cut the tree, strip the bark off,
and get started immediately and get the bow roughed out
and then let it dry.
And once you get the bow roughed out, it'll dry.
And depending on the conditions,
it could be as little as a month or two
before you can continue on with the bow building process.
Now, one of the things that you'll notice about hickory
as opposed to some of the other top tier bow woods
is it does tend to take a little bit of a set.
You can see that this one's got about a half inch a set
or so already, and we haven't even shot the thing.
Now, one way that you can get around that
with hickory and a lot of the other whitewoods
is heat treating the belly of these bows.
I'm not gonna go over that in this video.
It is something that I've covered over on my Patreon site,
and it might be something that I'll cover
in a future video here on YouTube.
So once you get your bow done,
you're gonna wanna seal these things up really, really good.
And you're gonna wanna do it pretty quickly,
especially if you're in an area
where there's a lot of humidity.
I'm down here in Florida right now.
The humidity is probably 80 something percent.
And so I'm gonna sand this bow down,
and I'm gonna get it sealed up as quickly as I can.
One of the things, one of the characteristics of hickory
is it tends to soak up humidity or environmental moisture.
And so right now the moisture content
of this wood is about 10%.
If I were to leave this thing outside overnight,
it would probably raise up to 14, 15%.
And that's just gonna cause it to take more set.
I use true oil, which is like a gunstock oil,
gunstock finish, and basically all it is
is boiled linseed oil with some drying agents in there.
So it dries a lot quicker
than just regular boiled linseed oil.
But that works really well.
I put six or seven coats on there,
and I take my bows out in the rain,
sleet, snow, it doesn't matter
because it's pretty much impervious to the water.
Right now I'm working on a very detailed video
that's gonna cover how to build a bamboo-backed Osage bow.
Hopefully it'll be out next week,
but with all of the shipping stuff
that's going on with COVID,
we're gonna have to wait and see if I get all my materials.
But that video is gonna be out before too long.
All right, guys, that's gonna do it for this week.
Go ahead and subscribe to the channel if you're not already,
and we'll see you next Thursday.