Segmented Spoilboard, with a side of logs and a flood..

Jay Bates
99 followers
537 Video Views·Aug 11, 2026
The CNC spoilboard is done. Well, the horizontal table. It's a similar but much different design than the last one. Less expensive hardware, more capability. Of course, a few scheduling curveballs. Unexpected events are becoming more expected..
Check out @TimberKingOfficial for more info on my 1220CRZ sawmill, or one of many Made-In-The-USA fully hydraulic mills: https://timberking.com/
Subscribe to my homestead channel @BPo3Homestead
----------
Special thanks to @AvidCNC
AI Generated·May contain errors
Jay's Custom Creations is supported by Timber King Sawmills.
For more information on my 1220CRZ sawmill or many other fully hydraulic sawmills, go
to TimberKing.com.
Well, we had a slight detour yesterday.
I was supposed to get the spoil board done, but I got a phone call that took priority.
We got a load of logs from a local tree service company.
Pretty nice, not chewed up cedar.
That's going to smell good on the mill.
And then a bunch of red oak.
This side is, this one right here is firewood.
That's probably a saw log.
And all three of these are beautiful red oak saw logs with some metal in it.
Because we are expecting some bad storms tonight and I have to unload these out on their lawn,
I guess the detour continues.
But we'll pick back up with the rest of the spoil board in just a second.
Well, the sun is shining.
Sure wasn't a few minutes ago.
Just came a flood and power went out and I haven't rebooted yet.
I don't think I am.
I think this is a good stopping point for today.
The spoil board's done.
It's done.
I say done because it's a spoil board and it's infinitely modifiable.
So my initial plan for the spoil board is done.
I've accomplished everything that I want to accomplish.
I have, it's a segmented spoil board.
I have a four by eight section over here, a sheet good section over here.
This side over here is segmented for beams.
And there's also some extra support in the back for any type of overflow for big tabletop
jobs.
However, it doesn't need to go all the way to the back.
So I'm saving a little bit of material by having a little bit of a gap there.
And I'm also saving a little bit of material by having a gap in between all of these segments
on the beam side over here.
I did go all the way to the back of the capacity.
As a matter of fact, I put a line right here.
That's the furthest travel for the center of the center axis of the spindle.
So I have all of my capacity usable, but we are segmented.
The reason why we are segmented is twofold.
Number one, because this gives me more area, more options to throw clamps on beams over
here.
Obviously, the big open area, I can do that.
But I also put these little cutouts here sized for a big F-style clamp.
So basically, no matter what dimension, no matter what length beam that I have, it should
be pretty darn supported.
If the end ends up being in the middle of this opening, well, I can shift it one way
or the other.
And then both ends will be on material.
So that's pretty cool.
I did not put any of the dog holes over here for alignment as far as where my beam ends
in this direction as it's clamped down.
I will likely put the dog holes in such a way that the reference face of the dog is
in line with this line right here on these pockets.
But I haven't done that yet because I want to put my first beam up here and figure all
that out as I go and simply drill the holes as I need.
All the hard work of figuring out, not really hard, but all the work of figuring out the
exact size of the dog holes for these exact dogs is done.
Speaking of these exact dogs, so that means I could put them anywhere.
Speaking of these dogs, my last setup, I use TSO Precision Bench Dogs, which are a really
nice product, but that precision is largely unnecessary for what I'm using them for.
So it's an unnecessary cost for the way I want to use them.
So I picked up these on Amazon.
They're really cheap and it's like 10 of them for like, I don't even know, I don't even
want to say the price because I forget it's been so long since I bought these.
But they are remarkably consistent in diameter, both the top diameter as well as the shaft
diameter that goes in the dog hole.
And that's really all that matters in this case.
So what I did is I just made one corner right here.
My last machine, I made it look like Swiss cheese with a bajillion holes and cover all of
your bases and you can put anything anywhere.
But I basically just used one corner.
So it was more capable.
My last setup was more capable as far as options.
But if I'm using the same option every single time, yeah, it's unnecessary.
If these get wallered out or whatever, I can plug them and recut them or I can put more
holes wherever as needed because all of this geometry, every bit of this geometry is built
into the machine file so I can add holes basically anywhere.
That's one of the reasons why I'm holding off on the on the beam side over here, because I
can put them in when I need them.
And that's that's fine.
So this section over here, the T-track, just like the bench dogs, the more expensive track
just wasn't necessary in this case.
The track that I used in my last setup was, I think it was armor tool track, and I had a track
on top as well as bottom.
And I used the bottom track to physically bolt it to the spoil board.
That way, as I clamp stuff down, you know, when you're clamping this down, it's putting an
upward force on these tracks.
And I was fearful of these little screws that come with the T-track ripping out of the
surface as this is clamped down.
The more I think about it and the more I mess with this setup right here, the more I think I
think these will be OK, just the screws that came with them.
This is inexpensive track.
So it's the opposite side of the spectrum from my last setup.
I bought an eight pack of these on Amazon, eight pack of 48 inch long T-track, and it was
like fifty two dollars.
So I picked up three packs, three of those eight packs, and I have a handful of these leftover
that I can use for shop stuff.
But the screws that came with them were about three quarters of an inch in length, so they
don't pop through the bottom.
I recessed the or I put the bottom of the track as close to the level of the first layer of
MDF. So if the screws rip through as I'm using this, the solution is to simply put a two by
four under here and use a longer screw.
And that'll do the same thing as that double sided T-track at a much, much, much less of a
cost. So this spoil board is is a fraction of the price of the spoil board of my last setup for
the hold down clamps.
One of the things that I really liked about that last T-track is it had a break every 12
inches to where you can insert a bolt from the middle of the track rather than being forced to
enter from the outside.
And that was really, really handy.
And I didn't want to lose that feature.
So I found these these bolts are where you can see them.
They're not quite a full circle.
So they've got a flat on either side.
And then you see this camera can't focus up near the top left corner is rounded at the top
right corner is pointed.
The bottom right corner is rounded.
The bottom left corner is pointed.
And that geometry allows that bolt head to go into the track no matter where you are.
And then you just twist it slightly and now you're locked under the track.
And there you go.
You start clamping down and to remove them, you just twist them the other direction and
remove them. Yeah, it just makes sense.
You know what I'm saying? It just makes sense.
So this whole setup is the spoil board is is way less of an expense than my last setup.
Another reason for segmenting all this stuff is this is a lot of surface area.
MDF, I have to drive 40 minutes one way just to to be able to purchase MDF, so it's not
convenient for me to get.
So I wanted to keep this whole setup to be two sheets of MDF or less.
OK, that way I only have to go with two sheets.
I don't want to do like two and two and a quarter of a sheet that's necessary to get all
this done or whatever it is.
So being segmented like this, I can fit an entire resurface on everything here in less
than two sheets of MDF.
That for me is a big win.
And of course, the the these segments here, it's unnecessary to fill up all the space.
If I was to fill this entire table with a huge five by 12 conference table to flatten,
well, these these missing spaces are pretty much irrelevant because there's enough
supporting material all the way around to accomplish that job.
So the spoil board is done.
It's done and it's going to be continually modified as necessary going forward.
I do have a little bit of planning still to do on this vertical table.
I am going to do a vertical table here.
However, I've been measuring pretty darn carefully.
And these rails are not coplanar on this front edge.
And I do have a little bit of a twist this way on these rails.
Not much at all, but enough to where I don't trust it for like, you know, doing some long
joinery on it or something.
It probably will be fine.
But I want to make it a little bit more precise.
That way it's in this is a CNC machine and and you have the precision built into the
machine. So let's make everything as precise as we possibly can.
So for that reason, I'm going to I've I've got it in my head.
I just have to put it in SketchUp and figure out how it all works.
But I need to be able to locate the table this way to make sure the top edge is nice
and parallel with the X axis.
I need to make sure that it's flat this way.
I'm sorry, not flat, but perpendicular, exactly perpendicular to the horizontal surface.
And then also in this direction as well.
So there's three different directions I need adjustments to.
And I think the simple solution is to use T-nuts on the backside of the spoil board with
set screws going into the rails to be able to manipulate it, really dial it in and then
some other screws into those tracks to lock it in place.
We've got an idea. I just haven't implemented it yet.
And I'm probably going to kick that can down the road just a little bit until I get
closer to actually using the vertical, needing to use the vertical table for joinery
because I've got to get going on some other stuff on here to actually put this thing to
use and get done with that blanket chest.
So that's, I guess, coming up soon.
I need to carve on the bottom side of the lid and maybe actually make some stuff to go on
the inside with the machine.
This cart, by the way, is just chest kiss.
This is the ticket right here.
This has been really handy to have.
Really, really nice being able to see this bigger screen right up next to me rather than
standing over here and trying to see it over there.
But anyway, of course, the dedicated cart is going to be better than a jointer for a
computer stand.
Another thing that is really awesome you saw me use in the video is this.
This feature just makes sense.
I was even pausing the job so I can clean up as I went and then putting it back on and
hitting resume. This is just, oh, I love this thing.
This is so cool.
Being able to take that off and sweep up as you go or when the job's done or whatever,
it's right there.
Use it. You know what I'm saying?
Good job, Avid. This week has been kind of crazy, like just about every week around
here. A lot of progress outside on the homestead.
Almost tripped over my dog.
A lot of progress outside on the homestead.
Of course, I'm behind on editing those videos, and I think this video is actually
coming out a day or two later than I initially wanted to.
But you know what?
Staying busy is fun.
Getting stuff done is fun.
If you're interested in checking out what's going on around the property, you can check
out my homestead channel.
I try to post on there more frequently than here, but things got really crazy lately.
So and a couple of things popped up in the middle of this job.
That's it for this video. You guys take care.
Have a great day and I will talk to you soon.
