Shop tour of a converted 3 bedroom apartment into a woodshop. Follow me on facebook @ facebook.com/jayscustomcreations Project plans: https://jayscustomcreations.com/plans/
Alright, just a quick shop tour here.
If you're not familiar, this shop is a 3 bedroom apartment in an apartment complex.
You know, you work with what you got.
But anyway, come through the front door and directly to the right I've got a dedicated
miter stand.
Just a regular 10 inch miter saw, no compound, no slotting, no nothing.
Just a regular chop saw.
All my stands for chop saws have always had this open area right here, I guess, from the
saw to your support.
I don't like a full table in here because as I'm cutting, as soon as I get done cutting
I'm going to take one piece, set it down, and I can still run the rest of my board through
without this board being in my way.
So I can run multiple pieces without having to put the board somewhere else, cut another
piece, put it somewhere else, cut another piece.
I've got a 10 inch sliding compound I'm trying to make a dedicated stand for so it just sits
in the corner for right now and when I need it I just throw a board across some sawhorses
and use it.
Two trash bins, well three trash bins that always stay two full.
Normally I don't keep any of my sheet goods here but I'm about to use that piece so I'll
just leave it.
Typically when I get my work started I stack all of my lumber into this corner, close proximity
to all my saws basically.
But this is where I load my lumber up for the current project.
A simple cleat system that was way overkill but I just happened to have a 2x8 and ripped
an angle on it and it worked.
Some upper kitchen cabinet salvage.
I'm short, that's tall, barely gets used.
This is my Porter-Habel table saw, a lot of bad reviews about it, a lot of good reviews
about it.
I'm pleased with it, I've had it for a couple months and I'll do a review soon.
I want to give it more time for it to sink in I guess before I put an honest review on
it.
From the back of the saw I've got about 12-14 feet that I can run something through if need
be for that long, actually that's closer to 16 feet.
And then from the blade to the window I've got 7 feet if I'm not mistaken.
So if I'm ripping down a 10 foot 2x10 typically then just open up the window, rip it through
all the way outside, it'll stay up and then it'll stay on my outfeed table slash workbench
or whatever and then get to cutting some more.
Typically this makeshift panel sled is always on my saw, I love this thing.
All my miters, miter gauges and sleds, I like to work from the front of the sled, that way
I'm close to the blade as I start, no need for a lot of unnecessary travel just to get
to the back of the fence.
Now I do have a bigger sled that I like to have the fence on the back side of, but this
is what I typically use right here.
I like the piece to be up front when I'm running.
A little extension I just made, going to make another one for this side, except I'm going
to do it a little bit differently.
This dresser, well it used to be a dresser, what used to be a dresser also used to be
my miter stand until I bought a cheapo table saw off Craigslist and it happened to be the
perfect height with this to be an outfeed table without the platform on top so I used
it as that.
And then I got this porter cable and it was considerably higher.
So a 2x4 standing up, 2x4 laying flat, and 3 quarter plywood makes that height exactly
like a 16th or an 18th of an inch lower than the table saw.
So it's actually just perfect for an outfeed table.
Which also works out great too, having this little I-beam support.
I've got my commonly used items under here like a cheapo brad nailer, a cheap pin nailer.
I don't use this brad nailer a lot, I leave it out here though because I have a dust cap
on the end of it.
I've got a Hitachi with a swivel on the end that I don't have a dust cap for, but this
is the lightest brad nailer I have ever used.
So that's the main one I use.
Little odds and ends storage in this one.
But anyway these little cubbies are absolutely great for just hiding commonly used stuff.
Hex bits, all my writing utensils, an El Cheapo dado blade set, one of the Fruit Advanti
Pro's Chinese model.
A lot of horrible horrible reviews.
Got this one as a gift and I'm lucky I got it.
It cuts absolutely great, absolutely flat bottoms.
Very happy with it.
I know I have not read one good review about it, but I got a good one.
Some odds and ends storage over here, Titebond and a little water bucket for my brush.
Behind the saw I don't really have, I don't think I have anything back there.
Just some coals, a little camera stand for when I'm recording, and got some old black
walnut that I'm trying to salvage, which I hope I can.
But most of it so far I've cut up has been trash in my dust collection, so to say.
I just stick that fan in the window, blow it out, and when I use the air hose, blow
out the shop.
Moving along from the bench, I've got a little stand I made.
This dry erase board is an absolute must for me.
I've got an attention span of a goldfish, so whatever I'm working on, I'll throw the
dimensions up there, and no matter where I'm at in the shop, I can quickly look up and
see what I'm doing.
Little drill station.
This empty spot houses this mobile assembly table, I guess you could say.
Just found this sink-based cabinet, threw some casters on the bottom of it, and put
a scrap piece on the top, and an instant assembly table, mobile, job, whatever.
But anyway, when I'm not working on something, I just slide it in this corner lengthwise,
that way I still have enough room to work in between the two cabinets, and also it still
leaves me about two feet to walk into here.
Like I said, this is an apartment, so obviously I've got a kitchen in here.
A lot of junk storage, whatever.
My day job stuff.
Little drafting kit.
I've got an associate's degree in drafting, which is completely pointless in the city
I live in, but just moved here a couple years ago, so anyway, long story.
DeWalt 735.
That thing is a beast planer.
Got a little in-feed-out-feed table.
I don't use this that much, but when I do, my goodness, isn't that thing awesome?
Just random storage here.
I've got a bucket full of, about two inches on the bottom, full of mineral spirits.
I use that to clean my saw blade, keep just a piece of plexi on the top of it for a lid,
but I actually just let one soak in there all the time, so there's the saw blade down
in there soaking.
A kitchen sink that was destroyed before I even got here, but tell you what, having
this in here, one of these days when I get to make my own shop, that is an absolute must
to have a sink.
Some type of running water basin, something or other.
I use this thing all the time, obviously with finishes and whatnot, but man is it ever handy.
I've got three spray guns.
I've got a little touch-up gun that I typically use for spraying smaller projects with clear
lacquer.
I've also got a larger, this came as a set, as that one, and this larger gun with larger
cup, Campbell Hausfeld, I don't know if I pronounced that right, came with a little
Walmart set for like 60 bucks.
That's what I used to start getting into spraying.
And since then, I've gotten a dedicated Harbor Freight gun specifically for my clear finish,
clear lacquer.
That way there's nothing other than my finish running through that gun.
I mean that was only 14 bucks, that's a Harbor Freight gem, one of the very good finds at
Harbor Freight.
Various old paints, someone told me on Lumberjacks, recommended this Target Coatings EM6000 acrylic
lacquer.
Several people actually recommended it.
Absolutely awesome stuff.
That is a really good finish.
Something I recommend doing, I wrote the price of what I paid and all the projects, I keep
a list of all the projects that I've done with this, that way I know how far my dollar
is going on that stuff.
I've got a dedicated can specifically for, I do a lot of pine projects, so specifically
for amber shellac, mixed denatured alcohol, and just some other Rust-Oleum paint.
I've got all my cheap Minwax stains, spray paints, and then wood filler and paste, all
my harsher to the nose chemicals, a little bit of Thompson's up here.
Random junk, and then my little safety supplies I guess, some gloves, earplugs, dust mask,
lubricants, manuals, my router storage, and one of the worst routers ever made, that is
a plastic skill router, absolute junk, not going to spend much time there.
Cheapo bits, a couple of decent bits, some other junk in here, I've been doing a lot
of cutting boards lately, so I keep this little tray for mineral oil and some other little
experimental junk, a little hardwood pile, just scrap little hardwoods that would otherwise
be junk for a project, but come in handy for little hard pieces that you need for jigs
and whatnot in the shop, a little tool station, way too many circular saws, way too many.
This one was given to me as a gift, it's the only circular saw I really use, I typically
use it with a 12 inch speed square cut off, cross cut, longer 2x10s, 2x12s.
This one, I had this, I forget the brand, this cut off jig for it, and I used to use
it a lot, I still kind of use it for ripping down longer 2x10s and whatnot, but it clicks
best more than anything.
This little circular saw, I found it in the trash, plugged it up, it worked, never used
it, never put a blade on it, maybe I'll find somebody who can use it and give it to them.
A little skill 18 volt combo kit, I traded junk to get this, so one man's junk for another
man's junk, these batteries are not that good, I don't know if a new battery will make these
any better, just a pretty junky setup.
The batteries, I mean they take like 5 minutes to get off, they're so horrible.
Got a little mini drill press scroll saw stand with a bunch of storage underneath, stuff
I typically use a lot, my DeWalt laminate router, and some disc sanding pads, my Hitachi
random orbital sander, this thing is a tank when you put some 80 grit on it or whatever,
that will chew through some wood quick, cheap little palm sander that I haven't plugged
up in years, and something else that will chew through wood quick, a 4x24 Milwaukee
belt sander, I have no clue how old this thing is, it was given to me years ago, and that
thing is, that thing will kick up some dust, put it that way.
I took my wife's dining table a couple months ago and made a router table for it, out of
it rather, and the whole table sagged right in the middle, as soon as I cut this thing,
it lasted like a week or so, then it developed a significant bow, so I just cut off the ends
and I'll throw my router in there occasionally and use it, but typically I just, the insert
I made is still bolted to the router, I just clamp it to a table or something, that works
just fine.
Got all my quicker clamps right here, bunch of 36s and some 12s, 32s and some 12s I think.
My go-to kind of shelf, you know, little push sticks, which used together are absolutely
great, a lot of people don't like this style because you don't have much forward hold down
pressure, but used in conjunction with one another, these are absolutely great, foldable
by themselves but great together.
Air hose, I've got, let me turn this light on, down this hallway, I've got my air compressor
hose, going all the way to that back bedroom, turns the corner and I put my air compressor
in the closet, in that room, piled up with a bunch of crap around the door, it's relatively
quiet out here.
The most horrible way to wind up a hose, I found out, every time, it's just a board,
two boards screwed together to give it a place to wrap the hose around, every time you unwind
the hose, you have to unkink the hose, it gets all twisted up, so typically I leave
about 12 feet hanging on the floor at all times, couple planes, couple other junk shelves,
all my bar clamps and these cheapo Harbor Freight specials, these are actually, I paid,
what did I pay, $6.50 for these, 48 inch aluminum bar clamps, well, whatever you want to call
them clamps, they clamp really strong but they twist, so for $6.00, 48 inches, you know,
it works really good.
Down this hallway, I've got, down this hallway, I've got all my 2x storage, I typically use
a lot of 2x10s and these are some 16 footers all the way down there, obviously we've got
16 feet over here, I've got 3.25 and 5.8 ply over here and then 1 foot gap and then I've
got a crap load of 1 quarter inch sanded ply, you know, this stuff was here when I
got here, when I made this into a shop, the permacomplex I live in, I'm also maintenance
by the way, that's why I've done this shop set up, they want it gone, so by gosh, I'll
get it gone for them, I'll make something out of it, my little assembly table, like
I said, I'll pull it out of the way, typically when I'm working on something, I like to make
a little sketch up drawing and then a cut list and then a cut layout and then I'll use
that in conjunction with these other platforms to cut everything, anyway, let me move this
out of the way and I've got my jigs on this wall, top one is a 8 foot straight edge for
the circular saw, cuts panels a lot easier, got a very crude quick set tenon jig, I say
quick set, it's quick for me to set, a little 45 degree compound angle sled, I set this
up bolted to my miter slot, my miter gauge for my table saw or just set it into the miter
saw, a couple of little patterns here, push stick pattern, bread box pattern, I like to
make a full size drawing of whatever it is I'm working on if I can, now this is a little
bread box so it's very easy to make one, you can cut your pieces, line them up with this
board and see if it fits, got some various other router patterns behind it, a little
miter saw or a miter sled for the table saw, this is just an MDF back with an MDF triangle
on the bottom of it, two little hand holes, I know this top piece of MDF will wear out,
I kind of built this as a prototype just to see if I'd like it, four little screws here,
pop it out and put plywood or whatever you want on here but this is of course MDF edging,
that's getting a little fuzzy, I don't think it'll last too much longer but does the job now,
when the time comes I'll replace it, I do a lot of benches and this little jig right here is
cut my assembly time down in half, basically that is the, this interior here is the frame
of the legs and you can set your leg in, set your leg in and all your blue cross sections is where
the glue goes, drop the glue on there, put the top horizontal pieces on, screw it together real
quick, good to go, these outside pieces is where you put your back support and then your back
slats will go across them, you screw them in place, very, very efficient use of the, or very efficient
build of the benches that I make and chairs, this is another panel slide I was telling you about,
crosscut sled, it works great, got a little box behind to protect yourself but it works great,
these saw horses are, these are work horses, they're not saw horses, these are awesome,
you know put them anywhere in the shop, do whatever you want to, they stack, they take
up one little footprint, good to go, use them wherever you want to use them. So that's it,
a long 20 minute shop tour I guess, you know mobile base, table saw, miter saws, you know lots
of storage, couple platforms for working on, working on items, there's three bedrooms in this
apartment and those two on this left-hand side are just junk storage for my job, back one is junk
storage, bathroom's blocked off, there's nothing in there anyway, so basically you know living room,
dining room, kitchen, shop, and an apartment complex, one of the benefits of being maintenance
to your day job. But yeah, hope you like it, hope you can you know pick out something in here that
might help you and thanks for watching.