Trimming Pottery Tricks — A Beginner's Guide

Art Galleries Worldwide
11 followers
39 Video Views·Mar 1, 2026
Trimming pots can be a tricky process. There are lots of subtleties and timings you need to get
right for the procedure to go as smoothly as possible. So in this video I want to discuss
the process in real depth. I'm going to be talking about the pot and the tools together with some
tips and tricks and small things I do along the way to make this process easier. When learning
to trim it can feel as if you're ruining lots of well-thrown pots but it's worth knowing that
Usually trimming comes at a point when your throwing skills are already developed,
yet trimming itself is a totally new skill and it needs a different approach and a different mindset.
The first thing you have to get right is the clay's condition. It needs to be leather hard
and on the firmer side if possible. You should be able to pick up, prod and move around the pot
without the walls distorting, nor should the clay be sticky or should you be able to leave
fingerprints in it when you touch it. And if when you're trimming the turning stick
immediately back onto the pot then that's just another sign that the clay is too soft to be
working with. Trimming is one of those processes where if you attempt to do it when the clay is too
soft or too firm you actually make the process more difficult than it has to be. So catching it
at this perfect moment when it's leather hard, not turning bone dry and definitely not too soft
is absolutely critical. So here we are with the pot on the wheel and the first thing I do is pick
it up to feel the weight and then I run my fingers over the walls to feel the cross section. I can
feel that there's more clay in the base and then the walls get thinner as they move upwards.
Essentially all I'm doing here is gathering data which will inform me when I trim the pot as I
know where to focus my trimming such as where I shouldn't remove too much or where more needs to
be removed such as the foot on this piece. Before I begin though let's weigh this piece as it's
always interesting to see just how much material is removed throughout this process. At this point
it's 829 grams which is about 1 pound and 13 ounces. Now the first thing I have to do is
arguably the most difficult part and that's centering this pot on the wheel head. When I first
learned how to trim pots I was told to use these rings on the wheel head to help. You can see that
if I place the pot down and spin the wheel the gap between the pot's rim and the white ring undulates
and this is because the pot is slightly off center. So what I do is find this point where the pot is
furthest off center and I push it inwards just a little bit and then I repeat the process again.
I identify the spot where the bowl is closest to that line and then I push it just by a few
millimeters away from it and essentially I just keep doing this until the pot spins perfectly
in the middle and that gap between the lip of the pot and the white ring on the wheel head is even
all the way around. At which point the pot as long as it's been thrown evenly and was properly
centered at that stage should spin without any undulations in the walls which I can see both
visually and by running a finger up and down the walls. Equally instead of using the rings on the
wheel head you can just hold your finger steady like this. You can then identify the part that
spins around closest to your finger and push it away from that until the piece becomes more and
more centered. Once again it's worth stating that if you don't properly center your pots you're
actually making the process more difficult than it has to be. As if the walls are undulating really
badly it'll be much more difficult to hold your trimming tools steady as the wavering walls will
mean you constantly have to change the pressure you're trimming with and the walls of the pot
themselves will end up dictating how you trim. Whereas in actuality you need to be the one in
control. The way I actually center fundamentally takes a lot of what I just spoke about into
consideration but applies it in a slightly different way. I still look for that uneven spot
between the rim and the white line but instead of stopping the wheel and pushing it gently with my
hands I give it a sharp tap and I keep tapping until the pot spins in the center and I can feel
when it's on center by letting my hand run over the pot or by looking at the rim and watching how
it spins in relation to the other rings on the wheel head but essentially I'm just hitting the
pot wherever it spins the most off center. Tap centering can be quite difficult to learn you
just have to remember the basic principles of where and when you strike it and very quickly
it will become intuitive and you simply won't think as you're doing it. One thing you can do
to make this process easier and safer is to apply light pressure downward with your left hand this
pins the pot down and prevents you from over tapping it which is when you strike it past the
central point and so with just a tiny amount of pressure pushing down I can make sure the pot
stays in the right place as I tap center it. Tap centering can also be done the other way around
simply by striking the base in much the same way as I was striking the rim earlier I identify the
side where it's projecting out the most and then tap it into the middle I'm pushing down with the
fingers of my left hand to keep the pot in place but it can be slightly trickier centering this
way up as often the rims of pots will be slightly uneven and even when perfectly centered there
could be a very subtle undulation in the rim but instead of focusing on that you sort of have to
observe the whole vessel and get the entire piece spinning on its most central axis I will be
trimming the inside of this pot just to neaten it up slightly and the way I attach the pot down to
the wheel is by brushing some slip around the circumference of the base I then place it down
as centrally as I can and then tap center the vessel so it spins in the very middle of the
wheel the friction from the tapping combined with the slip holds the pot down firmly and finally I
use the corner of one of these rubber kidneys which you'll see me using quite a lot throughout
this video just to squash some of the excess clay around the base into the metal helping to stick it
down even more securely I can give the pot a really good shake and try to move it off center but it
just won't and if you are trying this just remember to not use too much slip as if there is too much
the piece will just hydroplane off the wheel head so use it sparingly for this initial bit of
really as my aim isn't to remove much material I'm going to be using these cheap stainless steel
trimming tools they cost a few pounds each and the metal wears away as the abrasive clay grinds
against them but they leave lovely smooth and burnished surfaces when used and they can really
take a beating which makes them wonderful tools to learn with as you don't have to be so precious
with them compared to some I'll use later now the first and most important thing to discuss
about turning tools is how you hold them you definitely don't want to hold them by the end
like this with a very loose grip as it will be really difficult to apply enough pressure
horizontally into the pot to remove any meaningful amount of clay you also have very little control
when holding it like this so instead you want to grip the tool very close to the blade you
also want to tuck your elbow into your torso and rest your forearm on the plastic wheel tray all
as ultimately the blade itself is floating in the air with very little support so you need to hold
the tool and brace yourself in such a way that it's anchored really well and you aren't holding
it limply like this again trying to turn pots like this will just make the process more difficult so
you need to really grip your tools lean your upper body weight onto your forearm to keep your hand
steady and stable as you trim for the inside of my pot I don't want to remove much clay rather
I just want to smooth the surfaces somewhat and refine the rim so it comes to a sharper point
which visually will make the piece appear as if it's lighter and thinner which is one of my goals
with this piece essentially when turning pots the aim is to make the cross section of the walls
as even as possible from top to bottom inevitably when you throw pots there's always going to be
some amount of excess clay in the lowest section of the wall and the base and via the trimming
process clay is removed from those thickest heaviest parts so the piece feels lighter but
perhaps more importantly balanced a pot can be quite thickly walled and heavy almost as long
as the weight is distributed evenly from top to bottom so the pot is balanced what you don't want
is for all that weight to be focused in the bottom of your piece so it feels bottom heavy
once I've lightly trimmed over some areas I often use a sharp piece of straight metal
like this to scrape over those trimmed sections to ensure they're perfectly straight and flat
so they're in keeping with my style of work I also use the curved portions of these plastic kidneys
to sure up the curves in the base of my bowls it can also be used in the same way the metal tool
was to scrape over the walls and to remove any remnants left from the throwing process
and lastly for the inside I just define this angle here as a sharp ledge should cause the
that's eventually coated over it to react more interestingly and yes in this case I am holding
the turning tool in the way I told you not to previously but as I'm only removing a very thin
skim of clay it works perfectly when there are specks of clay or trimmings left inside the bowl
which I want to remove I run a piece of soft sticky clay over the surface to pick up those
last few tiny burrs of clay I also want to just bevel the rim ever so slightly so it comes to a
which again will cause the glaze that's coated over it to break in a more dramatic way revealing
a band of color that encircles the top in reality how you trim your pots has so much to do with how
you're going to glaze them and there are things that I do specifically with my work as I know it
causes the glazes I use to act in certain ways to remove the pot from the wheel I use the sharp tip
of this metal potter's knife by sliding it underneath the base first I use the flat end
to remove that seal of clay I created earlier and then I push the knife's edge underneath it
but first I make sure that my left hand is ready to catch the pot as there's a chance it can
dislodge and fling off to one side so my hand is there ready to catch it now the reason I don't
slip the entire base when securing the pot to the wheel is that would mean I'd have to slide the
knife all the way to the center which would make removing it actually quite difficult and so by
just slipping the outside I only need to slide the knife beneath it a tiny amount next I remove
any remnants of clay from the wheel head and this is just good practice really as I don't want any
pieces of clay lodging themselves back into the rim I just so carefully finished I know this is
sort of an exaggerated example and this pot probably wouldn't have run into that issue
anyway but it's just good housekeeping and in other cases with other shapes it might prevent
you from damaging your pot and having to repair it so with the inside trimmed I can now begin work
on the outside which is where most of the trimming occurs the pot is tap centered and in this case I
want to trim right close to the rim of the pot now normally this would be tricky to do as I usually
secure my pots in place with three pieces of soft clay like so but by doing this I obviously block
the area I want to trim so I need to find another solution in this case that's using a spinner this
is a nylon tool with a ball bearing between the two parts which means I can hold onto the black
portion as the white part spins I place the tool on top of the bowl tap center it which just makes
holding it steady a bit easier and then through this tool I push down firmly which pins the pot
onto the wheel head and prevents it from skidding around as I turn the lower section of the rim
now for the majority of the trimming where my goal is to actually remove a considerable amount of
clay I switch to using these tungsten carbide turning tools these are very sharp and they
maintain that edge even after trimming thousands of pots the downsides are that these tools are
quite expensive the blades themselves are really fragile and they are actually quite difficult to
use as they tear away at the clay so aggressively it helps if you're quite a confident trimmer
before you attempt using these I suppose the easy comparison to make is that you would never teach
somebody how to drive in a sports car these tools also don't leave as nice a surface as the steel
turning tools and instead they often leave slightly chattered textured surfaces so really when I use
these tools my focus is to remove material and then I'll do a majority of the cleanup and refinement
with the steel turning tools and my metal scrapers so I hold the tool with a firm grip push down hard
from above and then make contact I move the blade at a slow and steady rate so it's able to trim the
entirety of the walls without skipping over anything another really important thing to
notice throughout this process is how I connect my hands I push the thumb of my left hand against the
thumb of my right hand they're bracing against each other and it's just another thing I do
subconsciously to add stability to my movements and help keep that blade steady
with that part trimmed I can now secure the pot to the wheel which I do by pressing three lumps
of soft clay around it which I suppose are like the jaws you might find on a chuck on a lathe
when I press these down I don't push them towards the bowl itself as that could create a slight
deformity in the walls of the pot instead I push the lump of clay directly down and let the clay
that squeezes out be the clay that holds the bowl in position this way I'm just imparting less
pressure on the rim of the pot which can be one of the most delicate parts of the vessel when you're
learning to trim pots it's very easy to let the blade catch and be drawn around by the rotating
clay this is why I go to so many lengths in order to keep that blade steady as I work with it and a
good way to think about it is like this if a slight bump or undulation is in the wall you want to hold
the tool firmly enough that the blade cuts through it causing the walls of the pot to become more true
as you turn it and what you don't want to allow to happen is for those undulations to influence
your turning as the more you allow that to happen the more exaggerated those undulations become
and the more you lose control now it's time to turn the portion of the pot which needs the most
clay removed and as I'm going to be trimming quite aggressively I really anchor my body grip the tool
firmly and connect my hands and you can see that there is a slight irregularity in the lower section
of this pot but I just trim right through it without letting it influence the movement of
the turning tool as there's so much clay in the foot of this piece I want to trim a nice tall base
as if this bowl sits on a pedestal so I switch to a smaller tool and define where I want that foot
to begin this of course means that the wall beneath it is no longer straight and as a step
I don't want just underneath the foot so I'll use a flat edge turning tool which is reciprocal to
the shape I want to trim this portion and correct it much better I then use my scraper just to clean
up that surface and then one thing you should never be afraid of is to remove your pot midway
through the trimming process in order to judge how much clay you've removed and just to gather
some more information especially if it's a shape you're unfamiliar with or haven't thrown many of
the walls feel pretty good but there's still just a touch more weight I can remove from this lower
section but the foot itself and the proportions overall feel about right so back onto the wheel
it goes and I tap center much more gently at this point as not only are the walls thinner
but when trimming you also expose damper clay underneath which doesn't have as much strength
and with that done it's time to finish the foot which I think is the hardest part of
the trimming process apart from the centering I begin by just flattening the top just to clear
the grounds so I can see what I have to work with and the first thing I'll do is bevel this outside
edge here's the bowl without the bevel on a tabletop and you can see how the pot seems to
just blend with that surface as if it's melting into it visually this makes the pot appear to be
heavier and to change that I just bevel this outer edge and then burnish this outside portion and the
with the smooth side of one of these plastic kidneys and the difference this makes is rather
striking albeit just a subtle change the bowl appears to float ever so slightly as the pot
casts a more intense band of shadow underneath it this also creates a point of contact that's
much less likely to chip with use as it isn't just a sharp right angle the next step is to begin
hollowing out the foot and for this process I'm going to be using the rounded corner of this
particular turning tool but first if this helps you you can score a line around the base to
measure the outermost part of your foot well now for my first one or two passes my aim isn't to
remove a ton of clay rather it's just to set the foundations and turn up till that guide I set
myself so I know where not to trim beyond it's so easy to make a mistake at this part and if you
accidentally gouge away too much horizontally or vertically you can damage the pot irreparably by
making a hole in the bottom of the bowl or by shredding past the foot and making it completely
uneven when trimming like this I hold the turning tool with a fist really tightly and keep my
movements very even and consistent when you begin removing so much clay at once all it takes is one
wrong movement and for the tool to catch and the entire pot to fling itself out of its restraints
and off the wheel trimming with confidence like this can take years of practice and you certainly
shouldn't push yourself to imitate turning like this when you can just take it bit by bit removing
clay layer by layer and ultimately ending up with the same result even if it did take a slightly
longer time speed comes with practice I felt like the foot ring at this point was a bit thick for my
liking so I began to remove clay horizontally thinning out this portion of the pot so the vessel
sits on a more delicate foot ring as I approach a point where I feel like the foot might be deep
I periodically check the thickness by pressing down gently with my thumb and if I feel like
there's any movement or the clay gives in ever so slightly I know I can't go any deeper
once I'm happy with the finesse of the foot I burnish all the edges around the bottom
so they're nice and smooth and any coarse particles of sand which this clay body does contain
are pushed back into the stoneware I then stamp the pot with my maker's mark and rock it gently
from corner to corner so it leaves a clear impression I then do a touch more burnishing
especially on the top as by stamping my maker's mark some clay was displaced
upwards creating a tiny bump so I push that back down I blast the foot with a heat gun for a few
seconds just to take the soft edge off the clay so whatever material I place this pot on doesn't
embed itself into the foot for instance with my wooden wear boards if I place a freshly trimmed
pot onto one of those the grain of wood can stamp itself ever so slightly into the soft clay
I run this kidney over the rim just to soften it with that the pot is finally complete and let's
weigh it to see just how much clay was removed so at 508 grams that means I've removed 321 grams
in total which is just over 11 ounces this means that roughly a third of the initial thrown weight
was removed during this process and the pot went from feeling rather heavy to light and balanced
trimming is my favorite part of the process it's the process of refinement and it tends to be a
more mechanical careful process as compared to throwing which is probably why I prefer it more
you also don't get anywhere near as messy which as a potter makes for a welcome change I'll now let
this bowl sit under plastic to dry out slowly for a couple of days and then it will be bisque fired
waxed glazed and reduction fired to 1290 degrees celsius I hope you found this more informative
video helpful and if you did happen to make it to the end do let me know as it's always
interesting to see just how many people do anyhow thank you so much for taking the time to watch
and I'll see you next week
