867. Throwing Mugs for Beginners with Hsin-Chuen Lin~ a Class Demo at Palo Alto Art Center

Hsinchuen Lin
205 followers
538 Video Views·Aug 7, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
I will do two shapes, round shape and
the angular shape. And I also like to
show you how to lift up from your back
after you done with it. Uh it's very
simple, but people don't know how to do
that. There's a way to do it. Uh it's
much much easier. Okay, so let's start
our first shape of the mug. There are
several ways to do the handle of the
mugs. At least I know it's three to four
way of prepare your handles.
I'll do the round shape of a mug first.
Um
again
you see that watch my right hand is
always bracing somewhere that is very
steady. just used my
fingertip to kind of a control instead
of my right fingertip is moving up and
down actually while I'm compressing
using my left hand. So this hand is kind
of put it push this ankle and this hand
is helping my right fingertips. So when
I'm pushing down, this handax actually
helping my right hand.
And uh if your right hand is not moving
at all, the glaz is nowhere to go.
Right? So this is this is my left hand,
right? I'm pushing that angle, right?
This angle toward the center, right? And
pushing it down. Okay, this is the hand,
right? But you can always brace
somewhere. So this is the right hand and
left hand pushing down and then brace it
here and just hold your clay and your
right hand is actually guiding the clay.
So the clay is where to go. So the key
is laps here brace here on your splash
pan. Okay. Right. So that is centering
and then once you're done with it I will
you can either flat the top or you don't
that's fine. But I will use my thumb to
drill a initial hole here. Right? This
is my right hand and use my right thumb
and left thumb is helping it.
So this way of a drilling is you see
that the clay is under my control.
Right? I'm drilling it but the right
hand is always holding on here. Okay? So
the clay is nowhere to go. If you have
your hand like hanging up here or
somewhere like this,
it's unstable, right? So you see that
always my right hand. And then after my
initial drill in it, I going to go
deeper. Going to use my left hand to do
that. So drill from the center. In the
meantime,
kind of brace on my right hand. And then
my right hand is bracing on the splash
pen. So it's all connecting together
while I'm drilling it. See that?
Right. Three. And the both hand is also
compressing the wall. And my thumb, the
right thumb can hold it on the very top
to control the rim. So the ring doesn't
get it doesn't get thinner. It's just my
left hand is drilling it down
until I reach the right thickness. I
told you that depending on how thick you
want to leave your foot, I always leave
it about at least half of inch. Okay. I
I like my very tall foot so that when
I'm glazing, I can have my finger to
grab on the foot by half of inch. If you
are not sure, get the needle to poke it
and then measure it.
Push that
to my right hand, right? Push the
button.
uh depending on what you are making if
you're making like I told you that I am
making a round curve of a mug then you
open a curve on the inner part if you
want to do the angle then you open it
flat okay depending on what you making
so I am making the wrong mark so I am
open the base slightly curve
okay you can see that slightly curve
and then constantly
recycle your slip and you don't need to
spin your wheel super fast is that my
wheel is not a super fast if you spin
your wheel super fast you going to toss
out all the water all the slip in here
but my wheel is not super fast so it
stays here so my splash pen stay clean
right and now this part here is open I'm
going to just pinch just like we um
doing our bowl last week pinch
And right hand breathe in here. Breathe
in here. Right hand, the thumb and
fingertips. Pinch the clay. And slowly
but steady goes up
and slowly let go. Right.
And brush the slip over again. Or you
can remove from your fingertip.
Right. This is your friend. Don't wipe
it off. Put it back. Right. Put it back.
Especially on the inside. If you use a
water, water go get a puddle of water
inside. But that slip is actually
sticking to the wall. Right. So, it's
very good. And then for the outside, you
just dip your hand in the water and just
brush it over. That's all you need,
right? And then now I'm going to keep on
pulling it up. But my thumb is too
short, right? So, I'm extending my right
thumb so that my thumb is longer. Right?
Extend it this way. Right. This way. Go
in there. And then just pinch
and slowly up up up up.
And slowly let go.
And compress the rim. the compressing.
Let me put this back here.
For compressing the rim,
this is called H compress. It looks like
a H, right? H. So, you pinch here,
right? Pinch. And then this hand squeeze
alongside of your finger
and push it down. You see that? You can
make it thicker, right? If you wanted
to. You see that the rim is thicker. You
level it. If you don't compress it after
every time after you lift it up, it
might get wobbly more and more, right? U
even more and more. So every time after
you do something on to your wall when
you lift it or you collar compress it so
it to keep your your rim level. Of
course you can trim it. I will show you
how to trim it. If in case your rim is
not level, you can trim it.
But by doing so is that you always
control your rim so it's level and
little bit of a water outside little bit
water inside.
Right.
Okay. And slightly
color
compressed it.
Right. And then I'm going to do it again
right here.
thumb. And this time I am kind of a bar
it out. The inside is pushing out
a little bit.
Move up
and compress it again. Now if you want
to get a nice curve,
just get your finger there. And I don't
have anything outside. Just want to show
you how your inside hand can do. Right.
So go there and brace my wings together.
Right? So everything is very steady or
even you can put your thumb here. Right?
Try to stabilize it and inside hand is
slowly
barely out.
Right. Slowly belly out. And when you're
shaping okay so you want to look further
out further out to see how the the curve
is growing. Okay. Look for the profile.
Not focus on here. Look further out. So
you know, see here, I want this part
here to come out more. Right? So I go
and kind of bend my head here and
barely out.
Right? I see the curve, right? And I go
up and then
stop right here. So that's how you shape
it. Okay?
But if you want the outside to be nice
and smooth, you can actually use a rib
to do that. I grab the rib on your hand
and hold it and bend it. Okay. Some
people do to hold up the the rib this
way. That's too too sharp. It's like
scraping it. You want to actually let
the rib the clay follow the rib. So
you're holding the rib this way. Not
this way. This way. And then just push
push your wall against your rib and you
slightly bend your rib.
And you can see that now the rib after
ripping the surface is nice nicely
curved because I'm pushing the wall onto
my rib. So you see that this part here
is nice and smooth.
And then take care of the rim. Hold the
rib
this way
and slightly
push that wall against my rib.
Okay. And then inside if you have
something I have little bit of a slip
that I put put it in. Use a finger to
wipe it up
at the very final stage. And if you know
put the little bit of a swirl
the the mark there's a little slip and
then you do that and you will see that
little bit the curve swirl inside that
that looks also beautiful too cuz it's
like handmade. Okay. For the slip cast,
you won't be able to get that, but
handmade, you will be able to put that
that swirl in there. Okay. All right.
And then
the shimmy. Okay. People ask me what is
this? This is same material that you put
it underneath of your bed. Okay. Uh I
bought a big sheet of it's called
absorber. Okay. Big sheet. And then I
trim part of it for put it underneath my
back and some smaller piece I turn it
into a shammy. And this is good. Okay.
Good shammy.
And for the shammy you can go root make
a loop here. See that little curve
there. So I'm going to use the curve and
you are not holding your your shami like
this. You actually want to use a
fingertip. Okay. This two fingertip you
hold. You grab here two fingertip and
slightly squeeze.
So you are using the little curve to get
your rim into a curve shape. Okay. So
slightly go there, right? Go there and
then you squeeze it right. Squeeze with
your fingertips. Okay. If you do that,
it's little bit wobbly. Um it's very
hot. But if you have fingertip there,
you can control. Actually, you can push
it too. You can squeeze it, right? See
that? You squeeze it. See that?
Now the rim is getting thinner, right?
Thinner.
Okay. So, that is how you use your
shammy. And also last week I uh I didn't
cuz most of my work is quite level. So,
I don't need to trim it up. But I want
to show you how to trim off if your rim
is getting wobbly. Okay. So that
you can use a needle tool. Actually the
the uh the knife is better but you don't
have this can use the needle. I'm going
to use a needle to show you. So when you
are using the needle you want to go grab
and make sure you brace your wrist
somewhere that is very steady. And all
you need to do is go there and there and
there and go until it go through. You
are not going to go through right away.
So you have to let it go slowly. Okay?
Go in slowly. But when you pushing that
this needle pushing that it's little bit
wobbly. So what do you do? Get something
to support on the inside. Right? So put
your finger behind it inside. And you
see that now my wrist is connected to
here. And right hand is holding the
needle and this hand is supporting there
and the thumb is supporting here. So you
see that everywhere is connecting
together. So my hand is super steady.
That's that's the key. Okay. Steady
and then slowly go go. You see that? I
don't I take my time
until my inside hand feels it. I slow
down my wheel right and
lift it.
Okay, so that's how you do it, right?
Everything connecting together right
here, right here. Right. And connecting
together and slowly go go go until the
tip feels it. And then you don't know no
rush because you need to go the full
revolution until it cut through and then
you pick it up and you can slow down
your wheel. At the beginning you could
go but once you get closer right and you
slow down right and then you can lift it
up easily as long as you hold your hand
very steady. Okay that's how you do it.
Okay
that's that technique of uh how you
remove the uneven rim and then you're
going to compress it again.
And if you want a rim to be a bit
thinner,
see that I'm compressing the very far
end of the ri. The rim.
All right. So, that is a mug. And then
the clay from the corner, you can chop
it up. There are a couple ways to do it.
I don't have that uh the wooden knife.
You can use a wooden knife or you can
use this one of my tool that I design
it.
Scrap
push against your back. All right. And
keep on pushing your tool. And remember,
remove it. Okay. Remove it. Otherwise,
your clay might stick it back on to the
side of the wall. So, keep on going
until
you are satisfied with that.
Like that's the side cone that the side
on the back. And then you can hold your
tool sideway.
Right.
Slightly remove the clay from the
corner.
And you can put your foot
right there. Nicely. Okay. Nicely.
Because
some people don't like to trim. They can
leave a little bit of a style there. So,
it looks like you do it intentionally.
But if you are going to trim, it doesn't
matter. Okay? You don't need to do that.
But if you you can just uh remove the
clay from the corner. And I told you
that how you lift it. Okay? How do you
lift it after you're done with it? The
important part is make sure your
finger is all dry. Okay, dry. It's the
key. Okay, so make sure it is dry.
And then this part here is also dry. So
what I did is using the rip. So when I
was ripping, this part here is all dry.
So it's good. And then your fingertip
dry,
right? and then wire it.
Okay. Push your wire against your back.
Stretch it. Push it against your back.
And then you go and lift from the base
right here. Right. So, it's fairly easy.
You see that the rim stays right? The
rim is not wobbly because it's not slip
up my fingers. Usually when you pick it
up the the the rim
get torn is because it's slip of your
fingers. So it gets uneven, right? But
you see that like a scissors hand and
then you go there and then grab it.
Okay? And then you pick it up. Okay?
Thank you. Okay? So that's how you lift
it up from the wheel head. And now let's
do another shape. Make the angleish.
>> How much clay are you using?
>> Uh
this this it's about I would say 3/4 of
a pound.
>> Yeah.
>> So when when do you lift the piece up
versus leave it on the thing to dry? Uh
well uh for the studio if you are making
a smaller pieces we prefer that you
remove it from your wheelhead because
the bed is taking room and it's very
wide and sitting.
>> Yeah. Yeah.
>> Where on the
it's taking a lot of storage space on
the shelf. So remove it and we have
smaller tray or wooden board then just
lift it and leave it there. Okay. But if
you're mixing something very wide like a
a platter, then there's no way you can
leave it right away. Then you have to
try it on right on the pad. Okay? And
again, for you, if you want to get a
nice start, make sure your clay you slap
on it so it's get it into the center.
The more center, the better. Okay? If
you don't have a guide, you can use a
pencil to draw
several circles on your plastic bag.
This one already have the guideline. If
you are wood use a wooden one, use a
sponge to make some circles. So that the
the center the more center the better.
Okay? And of course if you are still
learning, make sure your clay is softer.
Softer clay is much easier for you to
squeeze it. Okay?
And I show you how to uh get your clay
softer last week. Right.
Right. You see that? I always do is
here, right? Put my right hand here and
use my left hand to go squeeze the clay
up and squeeze the clay down. Right?
This is the way, right? And my right
hand is not moving. Right? Even the clay
now is wobble a lot. Right? See that my
right hand get it back. Right? Hold it
and push it toward the center. Get it
back. Right? and use my left hand to go
up. Go down. You see that one?
Okay. This is This is off, right? So, my
right hand here, bring the clay right
this pinch. Get it back. And then the
left hand go push down. Right. Push
down. Right. This is my left hand.
Usually, you want to brace together, but
I'm going to just going to show you when
I'm pushing down. This is how I right
here. Right. How I did? Push from this
angle. You don't want to push from the
top, right? You don't want to make it
flat. Push from the side to the center.
Right. This is my left hand. And then
I'm pinch.
>> Yes.
>> You never watch it on the on the way
like you don't make
>> uh Yeah. A lot of people do that and you
see a lot of people on Instagram,
YouTube, they do.
Wow, it's very easy, right?
>> I don't do that because the the theory
of doing that is that you wet your clay
on the wheel.
>> Okay, but you already wed there. Why do
you need to w here? So, it's it's well,
some people like to do it that way, but
uh I don't I just just keep keep on
pushing it down. I don't usually it's
very seldom to see me like push the
squeeze sky high and then push it back
down. I consider that as a waste of
time.
>> What if you're doing a really big piece
like 8 lb 9 lb even that
>> even that I don't I don't do that. I
don't do that. That's even waste more
more of your your energy. Your see that
you want to push that 8 pound of clay
that high and then push it back down.
There's there's a technique that people
do that and then they kind of put put it
leaning that way and then push down. But
not all the people is very strong. So
like 8 pound, 10 pound, 20 pound of
clay. You want to squeeze it that sky
high and then you push back down. That's
you need to be very strong to be able to
do that. All you need to have the
technique to do that. Okay. But I don't
do that. I just for my large piece of
clay, I just kind of doing the skin,
right? Skin and peeling the skin of a
clay.
So it's saving a lot of energy doing so.
Right. has center the skin of a clay.
You don't need to squeeze it and then go
and then just pick down and then do and
even people say that you have to do this
four to five times.
Okay. No,
>> but the key is you want to get your clay
to the center. That's all. Okay.
All right. And now again
my thumb. You can use a both thumb too,
right? But you see that my right arm,
this is this is the key. Think of
yourself as a machine, right? You have
to some steady spot to do all the job,
right? You cut in the the metal or
whatever. There should be a arm to
support so that it's very steady. The
same thing when you throwing this is the
arm, right?
And you just brush. You see that? You
don't need to use a sponge and then
squeeze a lot of water. Okay? The water
go in there. All you need to do is on
your hand and touch up. That's all.
Right.
And until you got to the right
thickness, right? And this time I told
you that I'm going to make a angle. So I
will open up my base slightly
on the flat side instead of the round
one that I open the inside curved.
Slippery. Slippery.
uncompressed the base
and again the same way right you just
open it differently that's all and when
you pick it up the same way
you raise it up
uh you see that my hand is always
controlling the rim and my both hand is
always connecting together my arm is
always finding support Right.
Slippery.
Grab that.
You can open a little wider but usually
I prefer like slightly angle angle.
Okay. Slightly angle and angle. So what
I will do is get the base go in. Use my
right thumb.
Squeeze the base. So the base is
smaller.
Are you squeezing up?
>> Squeezing the base first, right? And
then I will pull this part out. Little
bit fur out, further out. And then lift
this part up. So the mug will be like
this. And this
push further out.
So there's an angle there, right? And
then here,
pinch right this hand. Usually I'll do
that, but I want to show you the finger
tip work. So I'm just using my finger
right here to support my thumb. So you
will see that
right. And slowly let go. on
compress the rim so it stays left
right brush the slip back to work and
now I would do it's already have the
shape so I just do the refining
get here use my finger and pull out
further
right and here
uncompressed.
Okay. So that is the uh the forming of
the mug and then you could do your final
shaping
this
make the shape more angle
right
the side of it make it more angle just
push that against it
hold my rib this way and the inside hand
is doing the up
and here slightly curve.
Okay.
Okay. And the final
cleaning cleaning.
Get my fingertip there and compressed.
And if you want to have a little bit of
a throw mark, you can put a little bit
of a slip on your fingertip. And then
you do that. So there's a throw mark on
the inside of it.
And then
here
compressed it.
Smooth out here. You don't have to if
you are planning to trim, but
just for the presentation.
And then
wipe it off. Top it up from the corner.
Hold it sideway.
Right.
This is my number 17.
Wipe it off. Pick it up. Make sure you
wipe it clean, right? wipe up your hands
clean and you can lift it up easily. So,
next we I will show you how to attach
the handles.
But here,
right? So, that's the inside of uh the
wall.
Okay, that is the mark making ankle mark
and the wrong mark. Basically, it's only
this shape. Either you go out or you go
straight or you go in, right? And then
you just walk around with the angle
angle or curve angle angle. You design
your mouth that way. Okay, it's only two
line, right? One, if you want to keep it
straight, so straight. You want to go
out and go out or go out and go that or
go that and then go that a lot of uh
play to play with that two lines
>> the contour lines. That's all. Okay. So
that is our mark making lesson. Thank
you.
>> All right.
[Music]
