We built a fence! Well, mostly. It took us five days, but we got the largest chunk of work done before the rain ended our drought. We never built a fence before, but I think we did alright.
PPO3 is supported by Timber King sawmills. For more information on my 1220 CRZ mill,
or one of many Foley hydraulic options, go to TimberKing.com.
Today we are building a fence. Well, starting building a fence. Neither one of us have ever
built a fence before, but we've got this thing called YouTube and we've seen it done before,
so that's what we're going to do is we're going to do what we've seen done before, right?
Yeah, sounds good, huh? So we're going to do some boards on a 45 over here to get our
string line nice and good, measure out the distances in between for all of our posts,
then move, mark the holes rather, then move the string, drill the holes for the posts,
put the posts in the hole, put the string back up and then wiggle the posts in the hole to get
or position the posts in the hole to get them to just barely kiss the string line. Sounds easy,
huh? Sounds easy. We're about to get fried in the sun though. Sound good? Like that too. All right,
let's go. So what I did is I set these down so that I could look through our posts and see that,
yes, it is going to hit this. And yes, it is going to hit this. And then I know from this
intersection right here that the drill bit needs to be mostly on this side because the post needs
to be here so that the side of the post is on this line and the side of the post is on this
line. Make sense? So right here is basically my drill point. If my drill point's right here,
it's not going to interfere with this. I think I made these too short. It would have been easier
to make these longer. That way it stays a little bit further away, but it is what it is. It's
pointing enough this direction, enough that direction. Measure the thickness of the board.
I need that side to be right at 90, which means this board is seven-eighths of an inch thick.
So my guide, my edge needs to be at 90 and seven-eighths. And now I can put the posts in
the ground, or the stakes in the ground on this side. And we'll be at 90 when I attach this to
the stakes. All right, we're jumping ahead a little bit. So the initial posts that I've had
in the ground for many months to say, hey, we're going to put a garden here, they weren't really
accurate posts. They were just a guideline. We just stretched a tape measure and just put a post
here and there, actually every 50 foot in the long direction, 30 foot in the short direction.
We never squared anything up. And I wanted to reference off of one of the initial straight
lines, the long lines of those initial posts. And I chose the wrong one. I chose the north side
line to reference off of. I should have chose the south side because we were nowhere near square
and had to re-square ourselves with the 3, 4, 5 method. You know, 3, 4, and 5 are your
measurements of a right triangle to make sure that you're nice and square. That multiplied out
so that our short measurement is not three feet, it is 31 and a half feet. Anyway, I just put the
done off camera. Let me show you how bad off our initial posts were that we put in the ground
many months ago. I got our string line set and we use this as a reference point. This was the
original post when we did a rough layout, well, rough measurements, and then now from our layout.
So we're accurate here. Obviously, it's our starting point. Look how far off we were over here.
So that's the initial post and that's where it actually needs to be. So it's nice and square
according to our string line. So we went through here and got all of our posts, our entire rectangle
nice and square with a layout line and using the 3, 4, 5 method stretched out, like I said,
to make sure that we are nice and square on this. And from there I used my long tape, which this is
a vinyl tape so there's a little bit of a stretch to it. It's kind of predictable though. And from
there I measured and marked out the location of all of my post holes so that way tomorrow we can
come back and take the string down and drill all of our holes for our posts, put the string back in
place, and then we can, you know, of course put the posts to where they just kiss the string line and
they'll all be nice and straight. Yeah, I've never done this before but like I said I watched a YouTube
video. So we're nice and straight here. Now the tape measure that I have is only a hundred
foot long, that vinyl or whatever it is, material tape. So what we had to do is come back to a number
that we can easily achieve repeatedly. Easy 10, 10, multiple of 10. My goodness I'll get it right
eventually. So that's what this is. This is 90 feet. Our next post is at like 93 feet so it's
right there. But that way after, you know, the tape measure ends right there we can continue on
further by connecting the tape measure right there and going all the way to I think the entire
distance ended up being 155 and a half, something like that. When we initially laid out the
the beginning posts, so that spray painted one that's been ran into several times and that one
over there, when we initially laid it out we were in multiples of 10, right? So it's 50, 50 and 50
for 150 feet, multiples of 10. But we decided to go with cattle panels for our fencing which is in
16 foot lengths. So then we had to, I threw it all in Sketchup and and made sure that there was just
a few inches, like three inches of overlap where each one of these is going to connect to a post.
But anyway, there's that. This looks like it just got, there we go. This is an accurate corner I put
in and that one's an accurate corner I put in. I had to take out the two initial posts. There's
one on the ground right there. Anyway, everything is laid out and spray painted on the ground
exactly where we need to put a post tomorrow and I'm kind of kind of excited about this. This is a
pretty cool thing. I think it's going to be pretty easy also tomorrow to knock out as many of these
posts as fast as we can with the auger on the mini skid and both me and Jamie getting this done.
Again, on this side we stopped at 90. That way I can hook on 90 and use my tape to go the rest
of the way. But I did put a nail right in the middle right there so I can have a reference
point to get on and get off of when I pull the string off tomorrow. So here's the materials we
went with. Did a lot of cost analysis and also trying to make this a relatively easy process to
put together initially but also easily modified down the road. If we need to add a section here
or there, if we want to, you know, extend the chicken side a little bit on this side or whatever
we need to do, this method of just using a post every 16 feet and a t-post right in the middle of
the panel at 8 feet, I think that's going to be pretty darn easy to manipulate, add, subtract,
whatever we got to do going down the road. These are six inch round, six inch by eight foot and
they're called, I think they're called ag posts, agriculture posts. And then these cattle panels
and we also got enough clips, two wire clips, to do the t-posts right in the middle. Also,
this corner over here is going to be the chicken run on this side of the garden
and these plum trees will be inside the chicken run. We didn't lay out for them just yet because
I'm not entirely sure if we want to go two panels for the length, which will be around 31 feet with
overlap, 31 and a half, or if we want to go three panels for the length, which will be 46, 47 feet,
something like that with the overlap. So we'll figure that out, I guess, as we go, but we still
need to do a little bit more layout, adding the chicken part. Well, today's theme is drill, baby,
drill. We've got a lot of holes to drill. I do mean drill, not dig. We're not using a post hole
digger. We're using a hydraulically powered auger that will go on the front of the mini skid steer.
This particular one is the RC-586. It's the bottom left right there. It's one of their
contractor series augers and these augers have a few different attachment methods, but this is,
let me get the thing open, this is from Bomalite. Bomalite's made in Canada, by the way. It's
manufactured in Canada. They don't import it and slap their name on it. It's all
manufactured in Canada and this is a big shaft. I wanted to show you this. Look at the size of
this drive shaft. That's not gonna, I don't see that breaking anytime soon. Two inch flat to flat
on the hex and if you go point to point, we're at two and a quarter inch. That is a big drive shaft
and the connection here, well that's, that's substantial too. This came with a bolt in it,
a bolt pin for attaching, but the auger itself or the hydraulic motor itself has a top link pin
in here. So I think because they included this, we're safe to use this pin. Just thinking out
loud here. So we'll get this bolt out, get this pinned into place and get it installed on the
machine. The only problem is, that's a lot of steel. A lot of steel and steel isn't light.
I think this thing is built like a tank and this is in the up direction right there. So I've got
to rotate this more than 90 degrees in order for it to mate up with the, with the universal plate
on this. So I've got to, I've got to move some steel. This is just water. Okay, water. That's
the second time I finally caught it on camera. The second time that this plate is somehow
holding water somewhere, but finally got it on camera. Tilting the front of this plate forward,
it just drained water. And last time I saw water on the floor, I thought, oh my goodness,
where's it coming from? I thought the machine was doing it, but I couldn't find anything on
the machine. So confirmation that it's something just pooling in here. Anyway, that, that was a
cause for concern. I'm glad I got that on camera. Also, this is kind of finicky to get this thing
rolled around and get it attached for the first time. But going forward, I'm going to detach this
in such a way that it's easy to reattach the next time I need to use it. It was just palletized,
of course, to get it here. The auger wasn't as heavy as I thought it was. This was heavier than
I thought it was. Go deeper. Paddles are only 50 inches tall. What a day, what a day. So first
thing this morning we got out here, we took down our string line that we had all the way around
our garden perimeter so that we could use our auger that we got with the bomba light to drill
these holes. We came out here, we got it hooked up. We were able to put 24 holes in the ground
with the posts. Currently, we have all of the posts in those holes leaning inward toward the
garden. We still have some more holes we're going to have to dig for the gate and for where the
compost bins will be in the future and as well as the chicken run. But we just haven't quite got
those mapped out yet, so we didn't drill those holes today. But I think we're out here for
about two hours. So that was us taking down the string line and getting these
holes dug with the posts in there. Overall, just wow, just an awesome machine we were
able to work with here. And so I feel like each hole was dug within two to three minutes,
just depending. And then of course, Dre had to get off, move it each time and then put a post in.
Our goal is to get out here first thing tomorrow. Right now we just kind of had to stop. It just
got really hot. We were out here yesterday and both of us got a little red from the sun,
so we just don't want to overdo it. And it just, it wears you out really quick out here. So we
just don't want to have any complications with that. So we're calling it a day. So for the rest
of the day, we're going to chill out in the AC. We have Kung Fu here in a couple hours.
So give us time to calm down and cool down from that. And then we'll be back out here first thing
tomorrow. We think we're going to get up early tomorrow and be out here just first at first
light so that we can come out here and just get these posts set in the ground and actually
tamp down. So what we'll do, we're going to take our string. We're going to put it back up the way
it was before. And then we're just going to get these posts where they're literally just kind of
touching slash kissing the string. And then that'll help determine and stuff if we got the post
exactly where it needs to be. And then we'll fill the hole back in with all of this dirt here.
Jay has like a post tamp, I think is what it's called. And we're going to really set the post
in there with that and make sure that they're secure. And then hopefully if we get that done,
maybe we'll be able to get some of the panels on and maybe even mark out the locations for where
the posts need to go for the chicken run and for the compost bins here in the future. It's just
been an awesome week here for us. Like we've had this going on. It's been really hot. We're in a
drought actually and stuff. Yesterday, our county got put in a burn ban. So it's been kind of fun
making sure all of the flowers and plants that we have planted have been kept watered here over the
last little few days. But again, we're not complaining overall. Very, very productive.
And then also yesterday, while we were out here with the string, not yesterday, I'm sorry, it was
two days ago. Two days ago, we were doing something in the garden. I can't even remember what. But we
and then the tree service that we're working with brought us two more
piles of wood chips. And that's just one of those like timing could not be better
because we were already pretty much out. We were scraping from the bottom of the last batch we had.
And now that we have this, we are going to, as soon as we get this fence up, we're going to finish
the roadway in there with the wood chips and hopefully have enough to get all of my raised
beds set in there. So a lot of things coming up this week as far as the garden, but a lot of
productivity as well. 6.53 this morning. Birds are always the loudest right at sunrise.
Other than the truck tires in the distance. Sounds lovely out here. All right. Step one,
get the string line put back up. Step two, put poles where they need to be and pound some dirt.
Your flowers have kind of taken off. Are you going to increase the density in this area?
You're going to attempt to? The sweet, what was that? William something? Sweet Williams. They've,
they're starting to cuddle away. This is such an interesting looking flower. I don't know
what the deal was. They're blooming now and then it's kind of going away.
This thing's turning into a jungle. I want to be like, do something. Is it going to flow?
It's supposed to have yellow flowers. It's supposed to have yellow flowers. Okay.
We're waiting on you, buddy. We're waiting on you, buddy. I didn't do anything last year. Like
it's really just shot up. Like last year it was like half this size and then it never got up off
the ground. It was kind of like flat like a pancake. All right. She's telling the flowers
to do something and I feel like I need to be telling that to myself. So I'm about to do something.
Golly.
Seven o'clock in the morning and already racing the roads. Someone's late for work.
It'll work.
Oh,
next hole.
I am gassed. I am, uh, I am at the quitting point for today. My hands have lost grip strength to
hold that post hole tamp. We got 24 holes in the ground and 21 of the posts set perfectly on the
string line. Nice and plum all the way up. Looks wonderful. There's two halfway down here that we
have to go back and do. We skipped those because the sun started baking us and we were chasing
shade. So just two on this line. Otherwise, otherwise that's a nice straight line right
there. Uh, and then we have this one corner post over here, which I have to take that post out and
shave the hole. I had to shave three or four of the holes. I wasn't as accurate with the auger as
I thought I was. Obviously it still saved an insane amount of time versus digging those holes
by hand. Uh, so that's cool, but you know, I have no experience doing this before. I have no concept
of how much time this should take. I don't know if I'm, you know, overdoing it by tamping all these,
these posts all the way around the hole. Really, really good. Uh, I don't know, but mentally I feel
like 21 out of 24, I should've got all 24 done today, but we worked for two or three posts and
then took a water break, two or three posts, took a water break, basically all day today. It's 4.30
in the afternoon right now. And, uh, the part that gets me is, is using this T post, T post,
using this post hole tamp. So this is, excuse me, this is a big steel bar. It's got a flat spade,
you know, on one side, or I guess a chisel edge on one end. And on the other end, it is a,
almost like a palm swell, you know, this part where you can mash the dirt down. It's a T,
it's a post tamp, right? Post hole tamp. Well, this weighs 17 pounds, which isn't incredibly heavy,
but seven, 17 times picking this up and slamming it down, picking it up and slamming it down.
Let me grab my phone real quick. I already did the calculator part of this. So 17 pounds times
approximately 50 pick up and smash down per post, which I counted 50 on one of them. And then I,
then I quit counting because it was a little bit more than that, but let's just say 50 per post.
And we did 21 posts. That means I lifted up 17,850 pounds today, just from that
post hole tamp. I keep wanting to say T post. It's a post hole tamp. So 17,850 pounds.
And that doesn't include the three or four, three or four that we had to take the post
completely out of the ground so I could shave the hole a little bit better.
Wah, wah, wah is me. I am exhausted. We're going to pick up tomorrow morning,
bright and early again, get these last three posts installed and then start putting up fencing. Now,
it's not just those three posts. This is, we're kind of doing this in phases. We still have to do
one, two, three, four more posts for the compost area. We still have to do one, two, three,
possibly four more for the chicken run. And each one of the gates needs an extra post installed as
well. But at that point, all of the major, uh, major structural posts will be in place that way.
It's very easy to just put a string line from post to post. And, uh, we can do those whenever
we're just trying to take, trying to, um, get as much of this done as we can before rain hits.
We've got, uh, on and off rain, rain, no rain, rain, rain, no rain in the extended forecast
for quite a while. So there's no way we could have gotten all the posts done before the rain.
But if we can get the biggest chunk of it done before the rain, that's what I'm looking forward
to. Right now I'm looking forward to an Epsom salt bath. All of the posts are finally tamped
into their resting location. Well, with the asterisk there, this is like the biggest phase.
Of course, like I said, we got to do the compost and we have to do the, uh, chicken run area. And
we have to add another post where each one of the gates are, but we haven't even figured out the
can look right down this line and I don't know if this camera is going to do it justice or not, but
right down this line, all the posts just kind of disappear all at the same time. Same with this
side. Actually that second one's leaning a little bit this way, but you know what,
these are ag posts and what we've realized is they're like this. Some of these have a
rather large snakiness to them. So, uh, we're pretty darn straight. Other than that,
other than that second pole right here, just kind of bending in, but it's the top,
it's not the bottom. Before we can put the cattle panels up, we need to measure out and mark and
install a T post right in the middle of every single one of these holes or posts rather.
Then we can put the cattle panels up and I've never done this method before. So I just looked
online and we wanted to have a little bit of an overlap, like six inches of overlap for the
panels just to give yourself some leeway if you messed up on the hole, just a few inches one way
or the other. That was the recommendation online. I think that's just a little bit too much. I think
we're going to have a lot of overlap that looks kind of goofy. Maybe, maybe not. I'm not sure.
But if it is, well, we can start a cattle panel right in the middle of a post and then wherever
the overhang is, we can just cut off one little row of the panels. I don't know. Maybe we should
just leave them full length. That way if we take these down, we can reuse them elsewhere.
But anyway, that's the plan for the panels. But right now I'm physically gassed. So I'm
going to switch over to computer work and start editing hopefully until this evening.
Maybe I can get back out here today.
All right, we've been working on this fence on and off all week. We started
the layout on Monday and today's Friday and we've got to stop because we're about to get soaked.
We got some heavy storms coming through and we're trying to get as much as we can done
prior to that. So every 16 feet ish is a wooden post. And in between each one of these wooden
posts can be a T post, right? So we've got this corner done to just kind of look and see how
things are going to go. And it's all right. I'm not super, super, super pumped about it,
but at the same time, I'm like probably over criticizing it. I've never built a fence before
Anyway, so we still have to top all the posts down to their final height.
And for the most part, we're getting nice straight lines up top visually. Those two are
nice and straight. There's one over here that's just driving me bonkers. We may have to reset it.
We got a little bit of a wave, not too, too much. Eventually down the road, probably next year,
probably not anytime soon, because as soon as this is dog proof, I've got to switch gears to
some other stuff. But eventually we want to add some horizontal wood pieces to kind of tidy up the
look of it, you know. So these first three panels, the top is nice and in line. However, we're
following the contour of the dirt. You know what I'm saying? So up here after the first three panels,
which is the, which is what we decided on for the length of the chicken run. So about 45 ish feet,
46 and some change feet, I think. This one is no cattle panel because we still have to put a
wood post right in the middle. And then one, two, three wood posts out here for the compost area.
And this whole side is not going to get any fencing at all. We're going to use, excuse me,
wood first and then corrugated tin vertically, right there, or maybe just all wood. I'm not
entirely sure. But regardless, this is the compost area. And then right after the compost,
we're going to have a four foot gate. That's a four foot gate. Oh, yesterday. I don't know
if I mentioned it yesterday. We went and got gates. I want to make wooden gates for this,
but again, who knows what I'm going to get around to doing that. So in the meantime,
we've got these metal gates. I believe the four foot gate is less than four feet. It's
sized so that it fits in between a four foot gap. I believe that's how it is. But right here,
the compost wall is going to be right here. And then we'll have another gate on the backside of
the compost wall is actually going to be a like a table, a workbench table, I guess,
for Jamie to do potting and such and also a horizontal shade so she can put pipes underneath
it to put all of our garden tools so that they are out of the weather and out of the sun exposure.
So compost gate right here. So I need to put another post there. That's fine. I can do that
later. And then the fencing picks up right here. Now, this is where the ground starts to do all
that kind of craziness. And we're we're mimicking the ground and I don't like it. So you can see
maybe you can see this post right here. The second wooden post from here is it's too high.
The post isn't too high. The fencing is too high. So it's nice. And this fence is nice and
horizontal and level here. And you can tell because the vertical line of the fence is nice
and vertical with that post. You go to this next one and then we drop off quite a bit from this
post to this post. And you can see that the panel is leaning down to the right. So therefore, these
vertical lines on this right hand panel are not vertical. You see that gap is larger right there
than it is right there. So either bring this side down and then these two tops don't match up
or slightly elevate this. However, we continuously go down in this direction. So I don't know what
the solution is, but that drives me bonkers. This panel goes up and goes down. That panel right
there is high and I don't know. We'll probably just deal with it and live with it and move on.
But we got it all the way down to the corner, which is nice, nice, nice, nice, nice, nice.
And this is what we're stopping for today. Like I said, everything's going to get
soaked here in a few minutes. And I've made the mistake once before of kind of pushing my timeline
in front of weather and getting all my camera gear soaking wet. And I'm not doing that again.
So we're going to come around here. This is another gate. This is a six foot gate. So
we have a six foot gate on this side. All right. On the left hand side or the north half
is where the six foot gate is. Same with up there. We have a six foot gate. My tractor
is was right there yesterday. Where is it today? Oh, tractors over there.
Tractor was is five feet wide, essentially. So a six foot gate should be fine. Hopefully it'll be
it'll be tight. But then again, I don't really plan on getting the tractor in here.
Hardly at all. Six foot gate should be plenty sufficient for Jamie's four wheeler and trailer.
That was the main concern. The fact that the tractor can get in here is just a bonus. I,
like I said, do not want to get the tractor in here. It's too big and cumbersome. You can't
make any turns. At that point, you're just dumping material. Well, if that's the case,
just dump it over the side. So plenty wide enough for the four wheeler. This whole half,
this south half, starting at this point is uninterrupted. It's going to be fencing the
entire way. So one panel this way and then however many panels all the way along. No gates or
anything on this side at all. This is the side that the ground floods and drains off in this
direction. So we're going to get to a point where we can barely walk over here. It's going to be so
muddy. But it's coming along. I'm proud that we put all these wooden fence, wooden posts in
nice and straight and on the string line. And yeah, it makes you feel like I'm a real fence
person who's never done this before. But all this will be covered up all the way,
connecting into our corner piece over here that we've already got. And then the fence
will be completed. Yay. Eventually. Yay. And then again, another six foot gate over here
on the center post on the north side of it. And it's going to be a straight shot
walkway all the way through. Jamie's already got a bunch of stuff already planted. As a matter of
everything you've got planted so far. So the first row of plants is up against the fence. Then we
have a walkway and then row and then walkway and then plant row walkway and so on. So what do we
have up here on the front? That first row is tomatoes. And then the second row is tomatoes.
And then these next three are tomatoes and basil. Tomatoes and basil. How many tomato
plants do you have in here? I planted 52 and I think I've lost two. So 50 tomato plants. Each
one of them is going to give out what, 6,000 tomatoes? We're going to be overflowing with
tomatoes, huh? Maybe. But that's okay because somebody is going to can all this stuff, right?
I'm going to try. You're going to try. That's what's up. All right. What's next?
Those are carnations in the bucket. Carnations in the bucket. Yeah. Put those in here.
Going to find out they're toxic. So I'm going to move them in here. Out of the way, dogs.
And then, so yeah, just jump tomato, tomatoes. Different species. They're all mixed up.
My labels got messed up. Half of them got washed away. It was a permanent marker. Not sure how
that happened, but it did. And then these larger tomatoes are better boys, I believe is what Nathan
said they were. And he gave me those. They were planted from, you know, a cedary and bought at
the store. So they're bigger than what I have, but hopefully they all catch up soon. And then
we skip over here. Skip over this orange dogs. You better stay out or you're going to get a yelling
at. Yeah. Line. So these two rows are corn and some of them have sprouted. The ones that have
sprouted like these two and the one down at the end, I have planted bush beans around. And then
I've also, I'm going back and putting squash. So the goal is for the corn to shoot up, for the
beans to trellis on the corn and then the squash to kind of provide, um. Ground cover? Well, ground
cover and stuff for weeds and stuff, ideally. And stuff because, um, this is just an old technique
that's been done. I'm just trying it out. I've only done it on two rows. And so, so we'll see.
Now this is corn, but it's planted thicker. So this is going to come out really close together.
And there's some sprouting on it too, but not many. And then Nathan thought it was being slow.
So he actually came yesterday when we weren't here and replanted. Nathan's awesome. Um, so I don't
know what all variety this is anymore because, uh, I think it's, I think it's a mixture of three
varieties now. So we'll just see what happens there. And then these rows over here are cucumbers.
All of these, this whole row here is like the longer type cucumber that comes kind of like
your slicing cucumber. And then eventually these will come up. We just put them here
for the purpose of, hey, a visual, hey, they're here. What are you talking about? Oh, the posts.
Oh, the posts will eventually come up. Okay. And then we're going to trellis them over. And then
on this side I have, uh, more cucumbers, but they're different species. They don't get as big.
They kind of are like the pickling, uh, cucumbers, uh, you can get that are kind of like as a whole
in the jar. And so that's what this is as well as that last row. So it would be a trellis here
and then it'll connect over this way as well at some point. Um, and that's where we are so far
here. And then yesterday Nathan brought me two blueberry bushes. So at the very end, I don't
know if you can see down there. We can walk down there. Um, so there's nothing planted in between
these rows right now. Not yet. Not yet. Okay. They're not even sealed. Like they're rocky.
We're not rocky, but comfy, I guess you'd say with the soil. And then Nathan brought these
two blueberry bushes. So we planted them yesterday and hopeful that they come on up and we just put
them at the end. And then I'd probably like to get a couple more, but I don't want to, I don't,
I don't know how big these get. Like I've never done this before. So I'm kind of blueberry bush,
blueberry bush. So we may just stick with two or we may get more. Tyler loves blueberries, so
we make it more. Yeah. And so I imagine that I won't do anything with these as far as canning
or making jams or anything because she's probably going to eat them as soon as they come on.
And that's okay too. All right. So you still have pretty much half of the garden this way
to play around with and add whatever you want to add, which I know you're constantly growing and
buying seeds and growing things and growing things and growing things. And I think that's
awesome. Of course, Nathan turned out to be your little garden buddy here. He brings me stuff all
the time. It's awesome. We need to get a little garden gnome statue and name it Nathan and put
it somewhere. Something like that. Nathan, Nathan loves gardening and Nathan's a good
friend of mine, long friend of mine. And yeah, you got a garden buddy now. Well, he says I can
come to his house and dig up pretty much anything I want. My mom and my sister said the same thing.
So here in a couple of weeks, we're probably going to do that. And it's hard because it's
like, I don't know where some stuff goes. I don't have a visual for it. Like we had a plan,
but uh, things change and then you get in here and you realize like spacing and whatnot. And so
it's a lot of room, but it gets filled up quick is what I'm noticing. Yeah. All right. We have,
we got these storms rolling in. So let's, let's get all the tools up out of the weather,
call it a day early. The rain is finally here. We've been in a drought for quite a while,
actually, uh, pretty early in the season. And this is normally a really big rainy season. I
think last year, anyway, we got a ridiculous amount of rain this year. We've been unusually
dry. So to see this type of rain where it's just, I mean, this isn't the downpour, this isn't the
flood. This is just good, steady, slow rain for many hours. We really needed this. Everybody I
know who has a garden has been looking forward to this rain coming. The rain was trying to start
on and off all day today. We would start to feel some sprinkles. All right. Well, we're expecting
a bunch of rain. So let's go inside. Nothing happens. We go back outside, put a couple of
panels up, get some sprinkles. All right. Well, this is the rain coming for sure. Go inside.
Nothing happens. Then we go back outside and put up a couple more panels. We've got about half of
the panels put up. All of the T posts in between the main wood posts, they're put up finally.
So we're not quite completely done with the auger on that just yet, but we were able to get
like the biggest chunk of it put up. So happy about that. Really wanted to get this all done
before the rain, but I don't know, maybe that was an unrealistic expectation. I feel like this,
you know, probably would have taken a crew of some guys just a few hours to put up and
it's a way more than a few hours for just us. That's for sure.