Whether you want to create a bird-friendly setting in your yardscape or want a simple, fun, and inexpensive craft project, this one-board birdhouse is for you! It’s a great craft project for kids and camps too!
#birdhouses #birdhouseplan #bestbirdhouse #campcrafts
This birdhouse is constructed from a single 6’ cedar fence slat. The actual dimensions of the birdhouse are directly proportional to the width and thickness of the fence picket. We use a Forstner bit to drill the entrance hole. The bottom of the house is removable and vented at the corners to reduce condensation in cooler weather and to facilitate cleaning.
You will find that small to medium-sized birds will be attracted to this house. It is welcoming of personalization through a wide range of finishes and paints. You can leave it “rustic” or spruce it up a bit. You can even put a metal roof on it. If you do, overlay metal on the wood roof substrate, or you risk overheating the little ones in the house when the roof is exposed to sunlight for an extended period of time. An old license plate or some roof flashing overlaid on the wood roof is a good choice and will extend the life of the piece while adding a bit of interest.
Over time, we’ve built over 100 of these birdhouses for events, gifts, craft projects, and around our home. We wish we could take credit for the idea or the plan, but honesty and courtesy demand that credit be given where credit is due. We found this plan on Pinterest®. We can’t locate an author’s or publisher’s name, but you can download it yourself by following this link:
https://www.pinterest.com/pin/573927546270983968/
You will see that in our version, we didn’t install a perch or a chimney, but that is up to you. Be aware that if you do install a perch or ledge outside the entrance hole, this can lead to the raiding of the nest by bigger or more aggressive birds.
As for the size of the entrance hole to your birdhouse, it depends on what bird species you want to attract and give a home to. Here’s an article that lists several hole sizes and the bird species that will be accommodated:
https://www.thespruce.com/bird-house-hole-sizes-386641
To build the basic version of this birdhouse, you’ll need one fence picket, 4 long and 20 short screws, exterior wood glue, and if you are going to hang your birdhouse, some stiff galvanized wire or a metal coat hanger. You’ll also need whatever paints or finish you are going to decorate your house.
The image from Pinterest may be difficult to read the instructions for laying out the pieces, so here they are:
LAYOUT DIRECTIONS
Using a pencil, start at the bottom of the board and mark 5 squares - the width of the board equals height.
Divide the middle square with an “X” - making the 45°angles for the roof.
Mark the roof pieces: the length of these should be the width of the board, plus 6 thicknesses of the picket.
Mark the last piece as a square for the bottom. It will be cut to width after the main house is assembled.
If you want to add a perch (not recommended if this is being used as a “real” birdhouse - as larger birds will use the perch to attack other birds or hatchlings in the nest), chimney, or other decorative pieces, lay these out and cut them out from waste pieces.
Then cut out and assemble the pieces as shown in the video, making sure to cut 45° angles on the long edge of the roof pieces as well as affixing a wire hanger securely.
If you need some more inspiration for ideas for birdhouse and birdhouse-themed yardscape decor, visit:
https://www.pinterest.com/dirtfarmerjay/birdhouses/
Sure, you can go to the craft store and buy a birdhouse, but why? With DFJ’s help and this great plan, you can JUST DO IT YOURSELF!
Follow us on Social Media to know when we’re building projects or releasing new episodes!
Instagram: https://www.instagram.com/dirtfarmerj
Facebook: https://www.facebook.com/dirtfarmerjay
You can help support this channel by buying our merchandise or supporting us on Throne or Patreon
Merch: COMING SOON!
Patreon: https://www.patreon.com/dirtfarmerjay
Hey Dirt Farmer Jay here from DirtFarmerJay.com. There is a great little plan out and about that
shows you how to build a functional birdhouse from one single picket. Stay tuned and I'll walk
you through it. It's a great plan. My wife and I have built this birdhouse many times for Around
Our Place but it's also a great craft project when the grandkids are coming over or you're
a youth organization. This is a great craft project and it is actually a functional birdhouse
that we find gets occupied year round. Now this plan has shown up many times in Pinterest
and I can't find who authored it, who owns it. If you know who did I'd sure love to give them
credit for it or if you're the author hey get in contact with me and let me know. But this is a
great little plan and it's an image so if you blow it up the type gets really plugged up. So as
a courtesy to you if you look in the description below you'll find this whole section right here
of the key measurements all typed out for you so you can walk through and get the main idea.
But I think you'll get everything from what I'm going to show you here. Here's what's really cool
about this plan. It doesn't matter where you are as long as you have a board like this. It
doesn't matter if the country you're in uses metric or it uses imperial measurements. You're
really using the board itself as the measure and here's how it works. You're simply going to take
a little cut off off the end of the of the board which I did right here to get a piece of the width
of the board. As you can see that is the width of the board and you're going to use this to create
all the measurements you need. So the first thing you're going to do here is create two squares so
that's the width there's the height right there so there's square one square two and you're going
to do this three more times but when you go to this one here just put a mark go up again put a
mark and now a solid now take a 45 degree square and put an x right there and what you've done is
created the ends of the birdhouse right here this is waste now you're going to do the two roof panels
and the roof panels are width right there plus six thicknesses right here so you're going to take this
one two three four five six mark that whatever that length is make another one then do one more
square and this is going to be modified to become the bottom that's inserted in the birdhouse
with screws so that it can be undone every year and the birdhouse can be clean cleaned or you can
put the interior to the sun and let it sanitize the sun to sanitize it before it is put in use
the following year and this is all extra right here now this board originally was six foot
or 183 centimeters and about five and a half inches wide or 14 centimeters to just give you
an idea of some of the dimensions we're working with in this particular setup i found that i
ended up with about 18 and a half or 47 centimeters of leftover and it may be that one of these
pieces split or i have a miscut and i'm able to use this and recover from this or if you're going
to make this a decorative birdhouse you're going to put on little chimney features or a front porch
or something like that that's where all this can be used from from that one single picket
now to assemble it we're going to use galvanized nails and exterior glue except for the bottom
after we cut the pieces we're going to put a 45 degree edge on both these roof panels so when
they come together the top they're just equidistant down both sides it's very clean
and there'll also be a little slot cut in it where we'll put in this shop made wire hanger
i did this from from some farm wire that i have but you can also use a wire coat hanger and make
a device like this so let's go ahead and get to work what we're going to do is cut out our pieces
right here using our little portable miter saw and we'll square these pieces we go any pair that you
make of something if it's the two ends you want to make sure they're exactly the same length and
height and if it's the two ends the pitched ends you do the same thing so the entire
birdhouse is now square all right let's go ahead and get to work and cut this out
all right now we have all of our pieces here we have the two main ends we'll drill a hole in this
in a few moments here we have two sides we have the bottom which will be cut to width and inserted
from the bottom and then they're the two roof panels which now we need to rip a 45 degree edge
onto these two so they'll match and put a notch for the hanger let's go do that all right so we've set
up the table saw to cut a 45 degree angle along the peak and what's going to happen here is we're
going to make sure we're orienting these boards so that the rough side is out we've chosen the
rough texture to be all around the board around the the birdhouse so don't get mixed up and end
up putting it through like that and then you end up with a mismatched roof outside get the texture
the same so here we go those are going to go just like that on the top of the birdhouse pretty huh
so i've put a mark halfway on one of the roof panels right here just halfway in the lengthwise
and we're going to put a slight notch in that that's going to allow this wire to pass through
and be captured and then this will sit underneath the enclosed birdhouse and make it so this can be
hung by this wire so here we go all we're doing on this is putting a notch on the top edge
all right now that passes through there just fine and we'll let the two joints come together all
right the last thing we need to do before we assemble is go ahead and drill the actual hole
in one of the ends here again we're going to do this as an outside we like to use about a
one and a quarter inch or 32 millimeter drill bit to do that placed about right in here you can do
it by eyesight if you like if you make it bigger than this it makes it easier for predator birds
to attack hatchlings or the eggs or to run off the other birds that find safety in there by using
a smaller opening like this they're safer another thing you can do is not put perches if you're
going to do a decorative birdhouse that's one thing but if you're going to put some kind of
shelf out here that gives a place for a predator bird to sit on and then put its head in and hassle
or kill the hatchlings or spoil eggs or whatever so if you're using this as an operational birdhouse
don't put a perch on the outside whether it's a post or the birds that use it don't need it they
can get in it just fine so let's go ahead and drill that hole all right so now it's time to assemble
it now what i like to do on the edge of my table is just put some push blocks where you can put it
into the corner and work again so you're not chasing the project all over the table so this
is a quick way to use an existing table without having to do the modification but give you a place
to assemble now let's make sure we orient each of these correctly we want this grainy side the
rough side on the outside that doesn't have any marks so we're going to start with that one there
and then we're also going to butt in a side to it now also you want to make sure you don't turn it
sideways you want the grain to be the same way let's go ahead and put some glue on it this happens
to be inside glue we're not going to be using this one outside but you can use the type bond three
or an external type of glue and then what we'll do is just go ahead and put them together push
into the corner and get them flush like that and then what we can do is pin nail that really quickly
let's go ahead and do the other end rotate around now one thing i want to point out very quickly on
this again you're making sure the grain is going vertical but you need to make sure that this
corner right here does not stand up above that and you can see it is just slightly that'll stop
the roof from really landing on it so i'm going to trim that piece just slightly so that it comes
down flush let me do that now you can see it fits right here at that corner let's go ahead and put
glue on both sides of this and pin it all together okay you now have the square assembly here wipe
off the glue there make sure of course the sides here go in between the two ends it won't work
putting on the outside if you put it on the outside of course that corner would create a
place that the roof could not go on so let's go ahead and put on one half of the roof what we'll
do is put on the side that doesn't have the notch all we're going to do is put glue right here we
don't need to put it there it just rests but we'll go ahead and put glue here and glue here
and then just eyeball where we're putting this here this is a birdhouse after all so if you're
slightly one way or another or if you want more shade over that whatever i just like to divide it
roughly in half what you're going to do is make sure that the point of the birdhouse is right at
the bottom of the joint or at the bottom edge of the angle of the 45 you don't want it up like
that and you don't want it down like this you want it about just right there and by pushing
it on there it's kind of tacked and set in let's go ahead and put in a couple nails
and then i look at it this way also just side along okay we now have the roof on it this is
all lined up very nicely and now comes time to put the other side with the hangers you can see
that goes together quite nicely and puts a really nice finish on that pretty cool looking huh so
what we're going to do is glue that top line of the joint here plus these two let's go and put
the wire in while we're at it we'll just let it drop kind of like that because it can pull back
up once we do that of course let's put glue in first put it all together just like that
now the hanger because it's trapped in there and it's turned that way it will hang just like that
and the birdhouse hangs now what are we missing the floor so the floor now is sized by putting
this on the end we know that the length should just be about right and there it is but the
width is off so what we're going to do here is put it in edgewise like that and then mark
where the other side is all right let's go ahead and cut that we can actually use our
saw right here to do that it's better to cut a little bit wide to begin with and then trim to fit
it's hard to add wood back on well look at that first first hit okay so that's going to go in here
now to provide ventilation that helps the birds be more healthy reduce parasites and that sort of
thing we're going to take a slight little corner notch off of each of that to create
little ventilation holes so here we go we'll just take a 45 off of each corner and just do a very
small one okay again these don't need to be precise but by eye you can see we did a pretty
good job there we're going to go ahead and put that here and what i'm going to do is pre-drill
four holes for screws we don't want to nail this in because this has to be taken out every year
so let's go ahead and get that done okay we're going to go ahead and put the bottom in now the
one of the things i do is just drive a little screw in it to begin with to create a handle
so that as i fit this if it falls in i can retrieve it without having to turn around and it
allows me to fine adjust it in the opening so what we're going to do here now is place this where
it's flush and i'm going to take another countersink and drill and right in the middle here
about half the thickness and you can actually pull this out and simply do it afterwards too
by doing like this and doing a countersink and just going around the perimeter
again doing it right about half the thickness of the board okay then we're going to take
one inch screws flush it up and then go ahead and drive the rest of the screws
be careful not to overdrive otherwise you'll split the end go ahead and remove your bottom screw
and you now have a complete functional birdhouse that will be occupied if you put it outside this
is also great for craft painting dirt farmer maggie has painted a couple of them around here
done little fences on them flowers looks like little flower gardens or little barns or whatever
they are real hit with the young and old i think you'll enjoy it well building this was made a lot
easy with a great little saw like this the seven and a quarter inch dewalt miter saw here this is
a cordless saw 20 volt seven and a quarter inch blade and we did a review on this if you'd like
to see what we liked about it how we put to use some of the features on it check out this video
here and then also while you're at it check out this other video that youtube thinks is perfect
for you and so do we hey just a reminder that if you check out the description below there's
a transcription of the directions of how to put this together and there's also a download link
for the pdf for these plans until the next time this is dirt farmer j from dirtfarmerj.com