Self Bow Building Tips & Tricks from a Master!

Unraveling the Ancient Longbow
4 followers
4 Video Views·Apr 17, 2026
All right, folks, in today's video,
we're gonna go through the entire process,
step-by-step of making an Osage self bow.
Now, if you're new to bow building,
I'm gonna try to explain every step of the process
and why I do things the way that I do.
And if you've been building bows for a little while,
maybe you can pick up some new tips and tricks
that might help speed up your bow building.
Now, we're gonna be working with Osage orange today,
and I've got a stave here
that has probably been cut for seven or eight years.
If you look at this thing, it's anything but straight,
so we're gonna have to address that with a heat gun.
But first thing we're gonna do is get this thing down
to one annual yearly unbroken growth ring,
one unbroken annual growth ring,
yes, that's what I'm trying to say,
along the back of the bow,
and then I'll show you how to lay this thing out
and make a bow.
Let's get started.
So before we get started on this,
I just wanna mention that we are using
a very simple toolkit today.
Primarily, we're gonna be using a draw knife.
We're gonna throw some other tools in there as we need.
We're gonna use a compass, a pair of calipers,
and a few other just odds and ends,
but primarily, this right here
is what we're gonna be using.
I've already got all the sapwood off this stave,
so we're just gonna clean this ring up
and get down to the ring below it
so that I know that I've got an unbroken ring
all the way across the back of this thing.
Now, this is a process that's fairly unique to Osage.
There's a lot of other bow woods out there
that you don't have to do this with,
but you can see, I'm not sure if you can pick that up
or not, but there's a growth ring exposed
all the way across the back,
then I've got one above it here and here,
and everything above this one has to come off.
So Osage is what's known as a ring porous hardwood
as opposed to a diffuse porous hardwood.
Ring porous hardwoods have very defined rings,
very easily discernible rings,
and in Osage, there'll be something called late wood,
which is a very hard, dense part of the wood,
and early wood.
Early wood in Osage is kind of crunchy
and it just doesn't have much substance to it,
but the good thing is that these rings of late wood
are separated by these rings of early wood,
and so when we're chasing a ring
or trying to expose one ring along the back of this thing,
we can use our draw knife more like a wedge,
and we can wedge in those early wood layers
to peel off the harder, denser late wood rings.
Now, you'll notice when I'm coming up to these knots,
I'm not just ripping straight across them.
I'm actually taking the back of my knife
and tilting it down a little bit,
and that changes the bevel,
or changes the angle of the bevel relative to the wood,
and it causes that blade to ride up those knots
so that you don't tear the top off of them
and violate that ring.
I'm also kind of going around them.
So I've got my ring all the way up to these knots.
Now, I'm just gonna go around the sides of it
so that I don't go across the top
and rip that top off and violate that ring.
Come to the back of it.
Get back down to our ring that we're following.
I'll just work back towards that knot from the other side.
So now we've got one ring exposed
all the way to right here,
so we'll just turn this thing around
and work from there back.
So when you shoot a bow, the back is under tension.
It's trying to pull apart,
so that's why it's important to have one unbroken ring
across the back of this thing,
basically so you don't have a fault line
where it can come apart.
So what we're gonna do now is take our draw knife.
We're gonna clean up this side so it's nice and smooth,
and then I'm gonna set a compass,
and we're gonna draw a parallel line,
and we'll get this thing to the same width
all the way up and down it.
We'll take a compass and set it to about like that.
It's about an inch and a quarter, maybe.
So there's a couple of different ways
that you can lay these bows out
depending on the stave that you're working with,
and the reason that I like to do it like this
by cleaning up one side and then scribing a parallel line
is because it follows the grain perfectly.
If you have a stave that does like this one,
it's got a big C curve in it,
or if you've got a bunch of snaky grain,
doing it like this will follow that grain
anywhere it goes rather than using a straight edge
and cutting across the grain.
So this stave is 63 1⁄2 inches long,
so we're just gonna measure
and put a mark right here in the center.
31 3⁄4, and I'll measure up two inches and down two inches
for our handle section.
We're gonna make this a symmetrical design.
So at this point,
there's a couple of different ways you could go.
You could go ahead and draw the back profile on here
and thin out these limbs towards the nocks,
but I find it easier if you get rid of a bunch of this
bulk material on the belly side here.
And so what we'll end up doing
is sawing a couple of slots down in here,
and we're gonna pop off,
we're gonna use a chisel and a hammer
to pop off big segments of this wood down here.
Now, doing it this way is a little bit risky
if you don't get your saw cuts in the right spot,
and the trick is to,
basically, you don't wanna go more
than about half of the bulk of the stave.
I say bulk rather than depth
because if you have a stave that is wedge-shaped
or pie-piece shaped,
you can go more than halfway down
because you have just as much bulk down here
in the widest part as you do
in that narrow, tapered-out part of the pie section.
This stave is pretty uniform from front to back,
so I'll probably end up going,
with my saw cut, I'll go just a little bit
beyond half the depth of this,
and then I'll stick my chisel in there
and pop off these pieces.
When I uploaded some of my oldest,
some of my first bow-building videos
probably 15 years ago,
I would just, at this point,
I would just take a draw knife
and start hogging off material,
and you can do it that way,
but it just, it's a lot of work
and takes a lot of extra time.
The reason that these saw cuts are so important,
the depth of these saw cuts is so important,
is because if you go too deep,
the split tends to run towards the thinner part,
so if you go too deep,
the split will run down into where your limb is gonna be,
and if you go too shallow,
it tends to run back up this way,
so you'll start deep down here
and you'll end up not really taking out much down here.
This one, I'm actually gonna go a little deeper on that one.
Now, when I'm prying on this,
I'm gonna watch this split
just to make sure that it's not gonna dive
down into the limb.
So the other good thing about doing it this way
is now you have two little miniature-sized billets,
and you can put these together
and make a kid's bow no problem at all.
So now I'm just gonna clean this thing up a little bit more
and we'll go ahead and draw our back profile on here,
and then we'll start making this thing look like a bow.
All right, so we're at the point
where we can start drawing our tip tapers on there
so that we can taper this thing out towards the nocks.
Now, you look at this thing
and it's got a big C curve through it,
and we're eventually gonna have to straighten that out.
And so what I'm gonna do,
when I draw these tips on there,
I'm gonna kinda cheat them
to the outside of this bend a little bit
to try to take some of that bend out
while we're cutting in the nocks,
and then we'll address the rest of it with a heat gun.
We'll do the same thing on the other side.
So we're gonna reset our compass to,
I don't know, something about like that.
We can draw our side profiles on here for our limb,
limbs, plural.
If you have a, like a felt tip Sharpie,
like one of those fine felt tip Sharpies,
that actually works really well for this,
but I don't have one, so I'm using a pencil.
Now, these lines aren't perfect
and they don't have to be.
We're just looking for kind of a rough guide for right now.
It's hard to draw a perfect line
when your wood's kinda not real smooth like this,
so we're gonna knock off the bulk of this,
clean up the sides so everything's smooth,
and then I'll go back and draw those lines again.
All right, so I've got everything cleaned up.
I redrew my lines on there.
Now, those lines are,
not sure what the gap is.
We'll just measure here and see.
It's about, oh, I don't know,
14 millimeters or something like that.
So what I'm gonna do next is take my chisel
and I'm gonna work these fades out.
You can do this with a rasp.
You can do it with a round on a belt sander,
tabletop belt sander.
You can even do it with a draw knife
if you like extra work,
but easiest way I've found is with a chisel.
When I'm going down to these lines,
I'm not trying to flatten this thing
all the way across from one line to the other.
If you do that, it's easy to focus on this line
and lose track of this line.
You'll end up with one that maybe dips down below your line
and that you really wanna avoid.
And so what I'm doing is I'm tilting my draw knife up
just a little bit so that I can run this line on down.
I can come back, run this line down
and I end up with a little peak in the middle.
The peak doesn't have to be very pronounced,
but it's helpful if you leave one there.
Once we get done bringing this on down to the line,
then we can come back with our draw knife,
use it as a scraper and kind of work that peak down
through the tillering process.
All right, so we've got this thing thinned out enough
that it's starting to bend or it would bend
if I could actually put pressure on it
without it twisting in my hands,
but it's so crooked that I can't put that pressure on there.
It just wants to spin.
So at this point, we need to do something
to straighten this thing out.
That means breaking out the heat gun.
All right, so what I've done is just took a couple
of two by fours, sawed a few slots in there
so that my limbs will fit in there.
And this is gonna keep the bow from rocking
as I put pressure on here and straighten this limb out.
So we'll start applying a little bit of heat right here,
heat it up, I'll start putting some pressure on the clamp
and we're just gonna take this bow and push it down
and straighten this limb out.
So when I'm heating this wood,
I'm focusing the heat on the belly side of the bow.
And the reason I'm doing that is because
if we put too much heat on the back,
the back is when the bow is drawn and shot,
the back is under tension and putting too much heat
on the back can actually reduce its ability
to withstand that tension,
it makes it a little bit more brittle.
On the belly side, the belly doesn't have
to withstand tension, only compression,
and so it doesn't really matter.
And actually heat on the belly side can help to harden it
and make it more resistant to compression
and make for a little bit quicker shooting bow.
But what we're doing right now is just trying
to heat this up just enough to get this thing to bend
and straighten this limb out.
All right, so this is cooled enough, hopefully it'll stay.
Sometimes you gotta do it multiple times
if you don't get it on the first pass.
So we'll heat this other limb.
Look at that, nice and straight.
So I had to go through, I think I heated one limb,
heated the other limb, and then had to go back
and do one more pass on the other limb,
but it came out pretty doggone straight.
And let's give it a little press here.
Barely even, this limb here feels a little bit stiffer,
so we'll start just by taking wood off of that one,
see if we can make it match the other one.
Let's see if we can't turn this thing into a bow.
Just kinda round these sharp edges off.
You know, when you're doing this,
you're really not removing that much wood,
but it really does make a big difference
in the way the wood moves and bends.
All right, so this thing's starting to look like a bow,
starting to bend like a bow.
So the next thing we're gonna do is take a pair
of just regular old calipers,
I've got a little lock knob on here,
and we're gonna look for thin spots.
A bow of this design is gonna taper,
ideally, from the handle section
all the way down to the tip.
Now, there's other bow designs
that get fatter down here at the tips.
That's not what we're after.
We're after a nice, smooth taper.
And so sometimes when you're scraping a tiller in a bow,
you can end up with thin spots in the mid limb
or just anywhere along the limb.
And having a pair of calipers like this
can help you identify those things.
So what I'm gonna do is just come along here,
slide these calipers along,
and you can watch the scale on the calipers.
And if it gets fatter or if it grows,
you know you've got a little bit of a thick spot.
And of course, if it dips down,
you'll know you have a little bit of a thin spot.
So I've got a little bit of a thin spot right here.
I'm gonna lock my calipers down.
And then I'm gonna take from here on out
and just look for the next spot
that I can slide these calipers down, which is right there.
So now I know that between there
and wherever I got those calipers on,
where was it, right here,
I know that I've got a thick spot right in there.
So I'll take a little bit of wood off here,
slide the calipers on there,
and take wood off until I can take those calipers
and slide them all the way down.
And when you're doing this,
keep in mind that if there's a knot there,
wherever it gets fatter, don't worry about that.
It's gonna, your limb's gonna be a little bit thicker
if there's any knots in that particular area.
And that's okay.
Now, right in this area, just watching the scale,
I can tell that I'm dropping thickness really quickly,
just like right in here.
So I'm gonna blend that thin spot
right on up into the rest of the limb here.
I think we're ready to cut some nocks into this thing.
All right, so what we're gonna use
to cut the nocks into this thing is a little tile saw
that will fit onto a hacksaw like this.
I really like these things
because you can get super accurate
and make some really nice nocks with them.
Yeah, that's what happens
when your tile saw sits around and rusts.
Dang it.
So we have got the nocks cut into this thing.
We're gonna see if we can get a short string on it.
If you look back at some of my older,
well, pretty much all of my bow building videos,
you see me using a tillering string,
which is just a long string that kind of drapes.
And really, you know, when I'm building bows myself,
I don't ever use,
I very rarely use a tillering string anymore.
I just go straight to a short string.
I think part of that is because I've built so many of them
that I feel comfortable getting them closer
to a final finished bow without ever even bending them
than I, you know, did
or that I do when I'm trying to teach someone.
So there you go.
First stringing, short string.
You can see this bend,
or this limb is bending just a little bit more.
So I need to take a little bit off of this one
and that should straighten her out.
We'll get it kind of even
and then we'll go put it on the tillering rack.
Oh, that looks much better.
All right, let's go put it on the tillering rack.
All right, so just pulling on the bow
a little bit like that,
you can see that most of the bend
is kind of in this interior portion here.
So we're just going to take a little bit of wood
in the stiff areas.
We're going to remove some of that right out here,
round these limbs over a little bit.
We'll come put it back on here and see what we did.
The limbs were fairly even side to side.
So we'll just take off,
I'll probably take off maybe 10 scrapes off this side,
10 scrapes off that side
and just try to keep things even.
Got a little bit of a thin spot right here
that I can just see with my eyes.
So I'm avoiding that.
It's like still a little stiff,
kind of right out in here.
So we're just going to repeat that process.
I'm going to take it back to the bench over there.
We'll take a little bit out of this,
kind of this section right here on both limbs
and bring it back.
But it's starting to round out.
So it still looks just a little bit stiff
towards the outside of the limb, especially on this limb.
But I think that's primarily due to,
this limb's got a little bit of a back set to it.
Now I don't have a bow scale down here,
so we're just going to have to guesstimate
on the weight on this thing.
But that was drawn all the way to 28 inches.
Just see what the weight feels like.
Still a little heavy.
It's probably, if I had to guess,
I'm going to say it's probably 65 at 29 inches.
So probably around 62-ish at 28.
Now, as you shoot these bows in,
as you just kind of break them in,
they're going to drop a little bit of weight.
So keep that in mind when you're building your bows.
You want them, when you want to finish them
a little bit heavy,
because they're going to drop into whatever weight you want.
With this one, I still want to take a little bit of wood
out of these outer limbs, round them out a little bit.
And that's going to drop the weight down.
But I also want to add a little bit of reflex to the tips.
I don't want to make a full recurve out of it.
I just want to flip these tips over just a little bit.
And that's going to add the weight up.
And so we're going to take a little bit more wood
out of right here,
which is going to drop the weight back down a little bit.
We're going to add the reflex.
That's going to bring it back up.
And then we'll have to bring it back out here,
see what it looks like.
Draw it a few times, see what it feels like.
So the thing you got to keep in mind
when you're tillering these things is
the thinner these limbs get,
the more each scrape counts for,
or the more impact it's going to have
on the weight of the bow,
how the limb bends and all of that stuff.
So when you first start this,
you can be really aggressive with your scrape
and you can take off a lot of real heavy scrapes
and maybe not change it all that much.
But as you sneak in on that final tiller,
just a few scrapes can make a big difference.
And so on this,
I might take off five or six relatively light scrapes
and just go back and see what it looks like
on the tillering rack.
You know, once you take that wood off,
you ain't putting it back on.
All right, we are getting very, very close here.
Got the reflex in the limb tips.
Let's string this thing up,
put it on the rack and see what it looks like.
Looks fairly even.
I think we might have a little bit more gap here than here,
but let's throw it up here and see what it looks like.
I'd say that's probably about 65 at 29,
which is where I want it
because it's going to drop a few pounds
as it ages and shoots in.
So now we need to decide which limb is going to be the top.
And what I'm looking for is just the gap.
It looks like we may have a little bit more
of a gap here than here,
but I'll put a measuring tape on there and measure it.
So I've turned the bow around now.
So this is the limb that was over here.
Just still looks,
still looks really stiff right in here to me.
So when I put this bow up on the rack and I pull it down,
the limb that was just on the left-hand side,
it looks like the outer part of that limb
is just really stiff.
But that's one of the things
that you really have to kind of watch for
with these natural staves is that this limb,
if you look down it,
this limb has actually got a little bit of back set
or reflex right in this portion.
And so if I were to take enough wood off
to make this round out
and kind of match the flow of the rest of the limb,
it would actually have to bend more
than the rest of the limb
because it would have to overcome this reflex
and then bend beyond it.
And so when you're tillering these things,
just you have to take those natural
undulations of the stave into account.
And it might not look perfect on the tillering rack,
but you're just trying to kind of split the difference,
I guess, between what looks right,
having a nice bend across the entire bow
and not taking too much off of areas
that are having to overcome things like this.
And the opposite goes for areas that have
deflects that bend towards the belly of the bow.
If you have a natural bend towards the belly of the bow,
you put it up here and it's gonna make it look
like it's bending more than it actually is.
Just some things to think about.
So even though that looks a little bit stiff,
I'm gonna leave it just like it is
because I think it's doing just as much work
as the rest of the limb,
and it's just having to overcome this whoop-de-doo
that's in the bow limb.
All right, so I'm just gonna measure the tiller here.
So we've got just over seven and an eighth,
and we've got seven and a quarter here.
So we've got a little more bend on this side.
So that's perfect.
That's the limb that I wanted to be the top.
So we'll go ahead and mark out our shelf,
cut our shelf in there.
We'll be ready to go fling some arrows.
So this bow is pretty much done.
If you wanted to, you could leave it just like this.
You could just sand it off, finish it off,
put a handle wrap on there if you want,
and you can go shoot arrows
and just shoot off of your knuckle.
That's perfectly fine.
There's a lot of guys that shoot self-bows that way.
Most self-bows are actually shot that way.
But I like to cut a shelf into my bow,
and so we just went ahead and put a mark on there
where the shelf is gonna go.
We'll go ahead, cut down through there.
We'll use our chisel to get down
and take the remaining wood out,
shape it up a little bit, and it should be done.
Now, I would not normally cut a shelf in with a Sawzall,
but Sawzall's what I have, so it's what we're using.
All right, we'll cut that shelf in partway
and put an arrow on there
just to make sure that it's gonna line up well,
and that actually looks like it's lining up pretty well.
All right, folks, so it's getting on towards the evening,
and we've been at this for a little bit,
so we're gonna just kind of hang it up today,
take a break, come back tomorrow.
We're gonna throw some Velcro
on this shelf and strike plate right there
and fling a few arrows and see how this thing shoots.
But I'm happy with the way it's turned out.
It's not taking any set, hardly at all,
and it feels, when I draw it, it feels really nice,
so I suspect that it's really gonna fling some,
that it's really gonna fling some.
And we're back.
So what we're gonna do today is go ahead
and just burn these nocks in,
just open them up a little bit,
because that tile saw's really thin,
and the string will barely fit in there.
Plus, I just like the way it looks
with those burned-in nocks like that.
So this is just a temporary thing,
doesn't have to be pretty.
I'm gonna end up taking this off.
This thing's quiet.
Helps when you hold onto the bow.
So this thing is shooting really, really nice.
It's definitely got some zip.
I don't have a chronograph or anything down here.
I don't even know what the bow weighs.
I'm guessing, I don't know, low 60s.
And it's probably shooting, I'm gonna guess,
maybe 175 feet per second with these heavy-grain arrows.
These are probably 640-grain arrows.
So anything over 170 with a heavy arrow like that
is, for a self-bow, pretty doggone good.
But it doesn't have any hand shock.
It's quick, quiet.
I like it.
I'm shooting, I'm grouping a little bit to the left
with these arrows, so may have to do some adjustment
with the, maybe find a different spine
that'll bring that group to the right a little bit.
Yeah, shooting the same exact spot every single time.
I'm only about 10 yards, but I've got a,
my group is, I don't know, they're all touching.
I mean, they're like side by side.
So this is where I'm aiming,
and hitting just a little bit left,
but you can see how tight they are together.
But that's something that can be corrected
with probably just maybe even something
as simple as changing tip weights.
But anyway, I'm not gonna get into tuning these things.
I've got a whole playlist on shooting
and tuning these things.
If you wanna know more about that, you can check it out.
So, like the way the bow shoots,
we're gonna go ahead and finish this thing off,
sand it down, make it look pretty,
put some sealer on there,
and we'll be done with this thing.
This is the worst part about building a bow.
I hate sanding.
So I've been using this clear coat from Rust-Oleum,
but I usually use the flat or the matte finish.
Hauls didn't have any, so we're using similar gloss today.
We'll have to knock the sheen down with some steel wool.
