Firing up This 1931 Atwater Kent Model H Tube Radio For The First Time!

Amateur Repair Time
257 followers
833 Video Views·Apr 5, 2026
This is a Model 72 we're working on, with a Model H chassis. Let's see if she wants to talk.
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time. We've been working on this
Atwater Kent Model 72 radio for several weeks now, and we've done a ton of videos on it. If
you haven't been watching them, you've missed out on a bunch of great times. So we did one where we
took the chassis out of the cabinet and kind of went over what all we had and checked it all out.
We did one where we replaced all of the capacitors in the sardine cans underneath the
chassis here. There's actually one up here on the top too that we didn't do.
That's for the tone control. Replaced all of those. Atwater Kent had a really unique way of
doing their caps, or at least in my opinion, they're unique. I haven't done a ton of the
radios from the 20s and 30s though, so it could be that a lot of companies were doing that, but
it certainly was something I wasn't that familiar with. Then we did a video where we
also did the power filter, the filter capacitors, which is in this
can right here. Did a whole thing on that. We did a video where we
checked all of the resistors and chokes and coils. Of course, had to replace a ton of resistors like
usual. We did a video where we investigated and figured out what was going on with the power
transformer. That's an actual replacement power transformer. Checked it all out. It seems like
everything's cool other than it may be slightly undersized for the amperage on the current on
the tubes. Jury's still out on that. We did a video. That may be all of them that we've done.
We're up to the point now where we need to test the thing. Oh yeah, we did a video where we tested
all of the tubes. I figured out that my tube tester had some problems. We fixed the tube tester
and then got a full complement of tubes that are working or appear to be working.
We've got an 80 rectifier. We've got 45 output tubes. We've got 27s and we've got 24As.
We're almost to the point we can fire this sucker up on the Variac and watch it,
but there's a few problems here on the top of the chassis that we need to
get into. One is the tuning capacitor is shorted against the blades. See how the blades are
touching the other blades in there? We haven't done anything with that, but if you look,
there is an adjustment actually. We've got to figure out what's going on with that.
Obviously, I don't think those should be touching. If you mess with it, you can get it to...
Let me see if I can do it by hand right here while you're watching.
You can get it off of them. It's just the whole thing is shifted back slightly. I don't know why
that is. Then the tuning knob up front connects to this with a little rubber connection that
has disintegrated over the years. When you turn the tuning knob, it's no longer connected to the
tuning capacitor. We need to work on all this and get this all working properly.
It's not meshing with it where it's touching it. There, everyone, I'm doing that. We've got
to mess with that. The volume control apparently on these is an issue that needs to be addressed.
You need to take it apart and clean it. I don't want to mess with that. Then this tone control
has contacts and stuff on the back of it. I'd like to take that loose and take a look at it
and see what we can figure out. I hope that power transformer isn't slightly
set up in a different way where you can't get that thing out. We've got to do that,
this, and that. Then once we get those three things done, we're about ready to fire it up.
Hopefully, at the end of this video, we'll actually test this thing out. Of course,
we won't have it aligned and all of that, but it would be cool to hear it come to life after all
this time and give us some noise. I think the first thing that I'm going to mess with is the
volume control. Let me see if I can remove that or what's the best way to attack that thing.
This is the volume control. To remove this, I'm going to have to remove these wires. There's
five lugs on it. I'm going to number them 1, 2, 3, 4, 5. 1, 2, 3, 4, 5 in the back there.
I'm going to put some tape on them so I can remember the wires because I have to remove
them to get that thing out of there. Then it looks like it's just held in with two screws
on the bottom and, of course, the knob on the front. All right, I got them off, got them all
labeled, and it had a bunch of heat shrink tubing on it that was real brittle and just fell apart.
We'll have to see if we can put something similar back on it, I guess, whenever we put it back.
This is it. 2, 5, 4, 2, 6. I think the thing is riveted together. It's riveted in place.
Maybe we'll get lucky. I mean, worst case, we'll break the rivets apart and put some
screws in it or something. I guess I could test it with a meter to make sure that it needs rebuilt,
but look at this. Does that mean somebody's already been in there? It's an interesting
contraption. This is our first hurdle. Okay, so I drilled out one of the rivets, the one on the top.
Oh, damn, I drilled out the one on the bottom. Well, I might be able to reverse it when I put
it back on. The whole thing is it mounts to this bracket, and on the bottom there's not much
room for a screw, so I'd rather put the screw on the top. I'm going to try to leave one of
them connected and just take the other one apart. And so when I drilled that out, it kind of
pushed itself open. It's like it's spring loaded almost. So they riveted it together, and that's
how the thing is made. This is probably a really nice design, so I'm going to carefully see if I
can get that bracket off of there so we can look inside of it. So look at the design of this thing.
So it has like a, I guess that's a carbon track all the way around it from here to here,
and then the wiper is here. And as it goes, it just pushes down this metal spring loaded thing
that contacts it to the carbon track. Look at that. And then if you go all the way around,
the other side is actually up, so it's just the part that it's pushing on that holds it down.
And then this one is doing the exact same thing on this side. So the thing is not touching the
carbon, it's just wherever it's turned to. So I got to be careful with this because if that carbon
starts breaking off in there, see how it kind of has already over here? I wonder if that's ruined.
That paint or whatever it is goes all the way to the pin on that. I guess I'll just test it.
All right, so I'm going to test it with a meter and I got to clean up these contacts. That's
obviously a big issue, but what a cool design. 1931. Oh, there was a, there was a, let's see
what it says. Sintralab, made in the USA, part number 25426. Sintralab, made in the USA,
25426. And it's big. I mean, it's almost two inches in diameter, probably two inches in
diameter. All right, I got it back together with the screw in it. It's my opinion after taking
that apart that you don't need to mess with those because there's really nothing you can do to
repair that carbon trace in there. So opening them up is really no help because there's a carbon trace
in it and either it's screwed up or it's not. It's actually, of course, listed in the schematic.
There's the volume control resistor. It's supposed to be 100,000 ohms. Mine's high. Mine's
like 150,000 ohms. And then this one, the other part of it is up here. It's supposed to be 250,000
ohms. Mine's like 500,000 ohms. So it's definitely drifted. Now, how bad that will affect the
sound, I don't know. It looks like they're turning down the... They're reducing the voltage on the...
Is that the grid? No, that's the... Yeah, I think that is the grid, maybe. Yeah, so I guess we'll
just see how it works. But the next one that I get, I'm not going to take that apart because I
don't think they're... You saw how clean it looked and if there's a problem with that carbon track
in there, there's nothing you can really do to fix it. So it's useless to open them up.
At least that's my opinion. All right, so I'm going to mount the thing back and solder all
the wires to it and then we're going to look at the tone control and clean it up. We may not
have to remove it. We may be able to clean the contacts from the back of it. All right, I got
it back. I was able to put the wires back where they go. 1, 2, 3, 4, 5, remember? Okay, so this
is the... Oh, and I put the knob on. Okay, so this is the tone control. It moves just fine. I put
the replacement knob on it as well. I can't completely remove that because I would have
to remove the power transformer just to get at the screws and I do not... I refuse to remove
the power transformer. I'm just not going to do that. It's a very simple device. So if you're here,
this top plate, this wire, is connected to one pin down there. If you're here, it's connected to
a different pin. If you're here, it's connected to a different pin. If you're here, it's connected
to a different pin. So there's four different tones that it can do. I don't know what it does
when it's in between and there's no markings on the front to tell you when you're on the pin.
That's kind of weird. I think what's going on, if you look at the top, you've got the four holes
there. The four little divots there. So I think what's supposed to happen is like when you're
there, you kind of feel it lock into place because that drops into the hole. But if you look, it's not
dropping into the hole and I'll show you why. I know the lighting isn't great. Here's why it's
not dropping into the hole because it's not actually touching that plate. This thing has
bent out of the way at some point. I'm going to see if I can get that screw out. I don't know
that I can reach it though because this transformer is right in the freaking way.
If I can't, I may be able to carefully bend this blade back here somewhere to make it have more
tension, but it's hard to do that. It's hard to bend it past halfway. This is the same kind of
little blades that I run into on pinball machines all the time.
I'm not taking this transformer out of here. It's a huge mess and it's not even mounted in
the proper holes. The thing was upgraded. It's not the original transformer. I'm leaving it.
And we've got like 20 different wires hanging off the back of it that we went through.
It's not going to happen, folks. We're going to have to fix the tone control some other way,
people. I need to clean all of that so that it makes good contact and then I need to somehow get
that freaking little indent detent to land in those things so that you can hear it click, click,
click as you turn through so that you'll know that you're on the proper thing. Because if you
just turn it, like it's not doing anything right now, but it's not even touching so it's not going
to work right now, but there's nothing to tell you that you're not right there in between two
tones. So I got to get that back and then, you know, I need to clean all that too so that when
it touches it, it makes good electrical contact. So let me see what I can do. All right, so I couldn't
remove it, but I was able to bend it to give it some tension. So, and believe it or not,
hear it? You can feel when it gets to the divots now. I guess that's as good as I can get it.
It turns real easy and I cleaned it with contact cleaner and I think that's good.
So I have checked it with my multimeter and it at all four positions it is connected with
no resistance from there to its wire on the other side. So I guess that's fixed.
Now the other thing about that is we changed all these sardine can capacitors and there's one here
that I didn't even know was there because we did all the ones underneath. So this is the same thing,
that's a can with a bunch of capacitors in it. And when you turn that tone knob,
what you're doing is selecting a different capacitor. Let me show it to you. So this is
it up here. Tone control condenser. Tone control switch. So I bet that would cause you all kinds
of problems if that thing wasn't touching like ours wasn't. Because look where it's at. Yeah,
so it's coming off one side of the transformer. The second AF input transformer.
And then it picks one of the four and you will be attaching a different size capacitor depending on
which one you're on. And then that will connect to this other side which goes to the other side of
the push-pull tube setup. So if that's not connected I wonder, I guess it'll work without
that. I'll bet a bunch of radios don't even, they probably have a similar setup but they don't even
have that tone control there. But I think ours is fixed now. So that was easy. That was a lot easier
than I thought it was going to be. I thought it was like more of a device. Oh and so the point I
was going to make, I didn't change any of these caps. However, when I did the sardine caps,
sardine cans, it looked to me like that most of them didn't need to be changed. Now I know that
sounds crazy but if you go back and watch that video, these were some nice damn caps in these
things. Very high quality. And as I tore each one apart, they all look to be still in good shape.
Now they were sealed in cans so no moisture can get in them. I understand there's other things
that can degrade caps and make them leaky and all that stuff. But I was thinking as I was doing it,
I don't know that you really need to change all of these. And then I did some research and a lot
of the guys that collect Atwater Kent radios, they don't change the caps in this era because
they're so nicely done even though they're a hundred years old. I know it sounds insane.
So I think I'm just going to leave that one because it's just the tone
control one. So it's not going to burn anything up or anything. I guess it could if they shorted.
You would be tying both of your push-pull together. That probably wouldn't be good,
would it? But we'll test it. We'll see if it seems to work pretty good with the original
caps in there. And if it doesn't, it's on the top of the chassis. It'll be easy to take it off and
re-stuff it with the new caps if we have to. But apparently the guys that are really into
Atwater Kents don't do that. They just leave them alone. So take that for what it's worth.
Okay, so that's that. So the next thing that we need to do before we can fire this baby up is we
need to work on this. And I showed you earlier, it doesn't mesh right. It's touching the blades
are all touching. And there's an adjustment here. So I wonder what's going on with that.
So there's something screwed up. I don't know why it would have moved. It's as if that adjustment
needs to go in. So I don't know. I don't know if something's deteriorated here or not.
But I know on that side, something is definitely deteriorated. It's hard to see, but the little
shaft for the knob is supposed to interact with some stuff up here on the front, and it's all
deteriorated. So we got to mess with that. Once we get that right, we'll look at that end to see if
it changes this setup in here at all. Once we get that right, we'll get this adjusted right,
and then we'll be ready to fire her up. All right, so it's kind of hard to see what's going
on. I haven't found an exploded drawing of this yet. This is the knob on the front,
and so it is a shaft with a rubber kind of sleeve on it. And you can turn it all the way to the left,
and you can turn it all the way to the right. I realize this isn't the greatest footage,
but if you look, there's a groove worn in it. It's supposed to be
rubber that turns this wheel here. And so if that rubber wasn't deteriorated, it would be turning
this, which not only has your dial indicator on it, but it turns the whole tuning condenser.
And it's got this weird little setup here. See how that moves? The reason that it's doing that
is because it compensates at the top of the dial. It's doing that to evenly space this out
so that when it's all the way meshed, you're at this end of the dial, and this is all open.
But it's not a... what's the way to put it? The face of the dial wouldn't be properly
laid out if it was the way that this moves. So whenever this moves a little bit,
so when you get to halfway, you're only at 850 or something like that.
This takes up some slack whenever it gets to the end so that the top end of the dial
can be linearly lined up the way we want to see it. But the stations are closer together at the
top of the dial. What's the best way to put it? Just a slight movement at the top of the dial
moves you from station to station to station. At the bottom of the dial, they're farther apart
in the way that this is set up. And so whenever it gets to the top, it stretches
the movement of the dial pointer so that they can stretch out how they've got the dial numbers.
So if they didn't have that set up and you'd have, you know, 550s down here,
you would have... I think it's normal till about here or something. So you might have 1110 and
then this would be 1400 and this would be 1600. So they have that thing on there to stretch it
so that they can make this dial... oh it doesn't even go to 1600... so that they can make this
dial more uniform. It's just one of their little neat little conventions that they put onto it.
I've read about it in some... I think I was reading an old book about the different Atwater
tent models and they were mentioning how they went through so much trouble to come up with that.
So this is the Sears Silvertone that we did a while back and look how it's lined up. Okay,
so right now I've got it about in the middle, which they're saying is 900.
It starts at 550 here. Look how much space is between 550 and 600. It's about an inch for 50
kilohertz. Then you get up here, look how much space is between 1500 and 1700. It's about an
inch for 200 kilocycles, right? So it's not standardized, but on the Atwater tent it is
because they've got that special thing on the tuning condenser. It doesn't do anything to
the tuning condenser, it just does it to the needle. So when you're moving the knob down here,
it's just barely going to move. Well, yeah, and when you get up here, it's going to move farther
because of the way that thing's designed. All that to say though, I need to replace that rubber
piece there. So a couple gentlemen online have figured out that a really good way to do that
is to just use a fuel hose. It's just a thick piece of rubber that you can cut and slide over
that shaft. So we need to pull that back out of there so that we can get to however that works.
I think I need to take those two screws loose and let me see how that comes apart so we can repair
it. All right, so here is the part and you can see what's happened. This just completely
destroyed it. So we're going to try to use a little fuel hose and just cut a new washer for it,
a new ring, and put it back in there. I should show you this too. I found this in the
just kind of laying in that area whenever I first started messing with it on the very first video.
So I don't know what they were doing. Were they trying to make some kind of sleeve for it or
something? That wouldn't work because it'd be too thick. Or is this a piece that goes in there that
came off or something? I don't know what that is. Almost looks like something sheared off or
something, but it's not. There's nothing, yeah, there's nothing messed up down in there. So I
was right by this. It wasn't attached or anything. It was just laying in there. So whatever. Okay,
so I'm going to... you can see that it's pretty much flush with this end and then it goes back
to almost the screws there and it just snugs up to that gear looking piece that's in there.
So let's see if I've got the right thickness of that to make that happen.
All right, so I found some fuel line that I had laying around that's 11 30 seconds
and it is pretty much exact or close enough to it. I don't know. I'd say that's about right
on the money. It might be a little bit larger, but it's close. And it's also... I think that's
a tougher material than this unless just... I mean this is a hundred years old, so it could be that
this was like that, but this is much more spongy. So I don't know if that's just because it's
deteriorated or if it was originally like that, but I think that might hold up better
against that gear. So basically that gear is going to be riding on it the whole time.
So let me see if I can slide this back in there and hopefully that'll be that. All right, we've
got it in there and when you turn the knob it opens the condenser. Now, we had the issue that
I just showed you a minute ago where the blades were touching. So what I did was there's two
adjustments. There's this one down here and then there's these three screws here that adjust these
blades. So I loosened those three screws and was able to move it just slightly to get it where
they're not touching. I don't believe they're touching. We'll have to keep messing with that.
I'll have to tweak all of them. But I'll tell you what, I think it's about time to see if this sucker
wants to come back to life. What do you think? Yeah, they're not touching. Yeah, I think it's about time to
fire her up. What do you think? Should we should we attempt to fire it up? I think it's that time.
All right folks, I've got a new toy. A guy was selling these local to me. 20 bucks. Can you
believe that? It's a variable AC power supply which you can use as a variac basically.
And it also has an amp gauge up to two amps. It's fused and isolated. So I had a problem where
my other one wasn't isolated. So I needed an isolation transformer so I can hook up test
equipment to these things. So we're going to try to bring it up slow. Now remember we already had it,
we already tested the power transformer. So let's see what we can do here.
So basically I'm just going to bring it up a little bit and then check the amps.
And I'm just looking to see. We've got all new caps of course. I'm looking to see if our amps
start going crazy. All right, so we're at half an amp. Let's see what kind of voltage that is.
We're at 40 volts. The pilot light or the the indicator light I can see a little bit.
Oh, I have a speaker hooked up to it as well. We're going to do a whole other video about
the speakers. But I do have one hooked up. Give a little more voltage. Now I don't have an antenna
on it or even a ground on it. So we're just seeing what we can do with our local station. There is a
clear channel station four miles from my house that you can probably pick up with a fork.
There it is. Let's check our, okay our amps are looking good. So we're going to go up a
You hear this?
So WBT 1110 WBT. One of the greatest radio stations of all of the times in the United
States. It started back in the 20s. One of the oldest in the country. One of the original clear
channel stations. It's four miles from my house here in Charlotte. It's a pride point for the city
or it ought to be, right? At one time it was in a battle with WSM to do the whole country music
thing. So WSM in Nashville with the Grand Ole Opry kind of became the city of music and all this.
Charlotte used to record a lot of music in Charlotte and stuff way back in the day. A
bunch of blues albums and stuff were recorded here. I mean way back and they used to play
all music back in the day but then they now for years they've done talk radio and stuff like that.
Now on 1110 if you tune to it they just play freaking a constant commercial telling you to
listen to the FM channel and it's playing music the whole time. It's been going on for like six
months. It's disgusting but anyway we lost our signal. Maybe my might be the volume. Let's go up
with the voltage though. Check our amps. Dump it around a little bit. Now I know originally it was
at 115. I was just reading some of their repair documentation that Atwater Kent put out in like
1931 and they mentioned that it was checking it at 120 volts. So apparently even back then
they were planning on them running at 120 but the tone knob's working. It's the one tone.
The reception is not great obviously. I don't have an antenna on it.
Let's see if we get another channel and we haven't aligned it or anything.
Yeah that may be all that comes in with no
So it's 1110. It's a little off. Tracking's off a little bit.
That's pretty amazing. Let me turn off some of these lights.
So that's WSM 650 out of Nashville. I have no antenna hooked up. Zero. There's no kind of
internal antenna at all and it's picking up a radio station from 400 miles away.
300 miles away. That's supposed to be 650 which if you think about it it's a little low. Just like
1110 was a little low. So it's tracking pretty evenly across the dial without even any adjustments.
These must have been just awesome radios in there. Dan this thing's from 1931.
I think it's the first Atwater Kent Superhead set. That's just incredible performance with
no antenna. That's nuts. I'm not so sure about this volume control. And I think these don't
have AVC so you're just going to get a low signal or a high signal. Whatever happens.
It's up to you to adjust the volume. And the tone caps remember we didn't replace.
100 year old tone caps and they work just fine. It's pretty selective with no antenna. That's
crazy. All right so there we go. We have broader back. So I still got more to do. I need to show
you the deal with the speaker. We got to figure out the deal with the speaker. We got to refinish
the cabinet or at least part of the cabinet. Certainly the top of it. We'll figure out what
we're going to do with that. And we need to align the radio still. But we're making good progress.
So I think we've done pretty good. So I hope you enjoyed it.
Leave your comments down below and I will see you on the next video.
