Uh Oh... Replacement Power Transformer In This Atwater Kent Model 72 Radio From 1931...

Amateur Repair Time
257 followers
187 Video Views·Mar 16, 2026
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time.
We have been working on this Atwater Kent Model 72 1931 console radio.
And we've done all kinds of videos on it. I think we've done four videos so far.
We did one where we worked on it, removed the chassis, took a look at it,
kind of saw what we were messing with. We did one where we re-stuffed these sardine cans.
These are where all of like the coupling capacitors and bias capacitors or whatever
are. And then we did one where we worked on the filter capacitor. We cleaned up the chassis.
And then we did one where we checked all the resistors, replaced all the bad ones,
checked all the chokes and the transformers with the exception of the power transformer.
Got all of that going. And so now we're up to, we need to figure out what's up with this
transformer. This is the wrong power transformer. I kept saying it was the output transformer
in the previous videos because it kind of looks like one when it's got all these connections to
it. I thought that's what was going on, but no, that's the power transformer. There's some bad
wiring. Things have been rewired and I don't know what in the world they're doing. So one of the
issues is, so this is the original schematics, how it's supposed to be. Oh, and by the way,
I know that that's a replacement because you can see the original screw holes.
And then they've got some plates in here to hold it in place in their new screw holes.
Right. And then you can tell that this wiring has been changed because they've got it taped
together. I took the tape off of that, but you also can tell that they did it a long time ago
because the rubber, they put rubber wiring in that's rotting away. Okay. So on the schematics,
it shows it as all of the filament wiring, all of the filament power is all wired together.
So if you look with the exception of, I think the, yeah, with the exception of the rectifier tube,
it's handled a little differently. Or actually, you know what? Maybe not. Let's look at that.
Yeah. Okay. Yeah. That's different. Okay. So if you look, these two wires come out
and they go to 2A. And then there's a connection here where it also goes to the oscillator.
And there's a connection there where it also goes to 2A2. Right. And then they run around from there
and connect to the first detector tube and then also connect to the second IF
and also connect to the first IF. The dial light runs off of that.
And then there is also a connection here where they run over to the second detector
and they run over to the first AF tube. And then they also have the filament shunt resistor
attached to it. Right. So, so this one winding connects to all of these, but the way they've
got this wired up, they've got them separated and connected to different parts of this transformer.
I would assume that the way they did it worked, you know, and maybe that's why we're doing it.
I don't know why they would split that up unless there is a difference in the amperage.
So I'd like to find some kind of identification of what that is. Obviously there's a number on
it, but I don't know that I'm going to be able to find the schematics for that, but maybe.
So they've got it connected to pins 5 and 9. And I had a couple other ones that it was
connected to. So there's just a, these are connected to a couple different sets of the,
of the lugs on here. So that's next. So I'm going to try to figure out what this is.
And the reason I want to figure that out first, before I replace the wiring is because maybe
we're not going to put them on the lugs that it's on. I mean, maybe,
maybe all of the filaments are going to end up on the same two lugs again. I don't know
right now they're on four or six, I think. So let me see if I can research this. So it's a
P2860. I hope that's the, I hope that's the product number. It does have a label on the
transformer. So I should be able to find some kind of record of that and figure out exactly
what we're even looking at. Okay. So I have actually found it in an old catalog.
Took some digging. This is the mount, type G mounting. It's a 2.5 volt amplifier filament
supply. So I believe that's what we need, right? And it is the P2860. I don't have a diagram of
how it's laid out, but we can probably figure that out with a multimeter.
350, zero, 350. Let's see what that is. Plate supply, AC volts, DC milliamps, 90 DC.
So the AC volts, I don't know what that means, 350, but they're all something like that. So
whatever. So that's that. And then I've got, like I said, it's a scan of this catalog,
so it's not perfect, but 5.0, 5.0. So rectifier filament, volts and amps. So
5 volt, 5 amp rectifier, is it 5, 3, 5 volt, 3 amp rectifier filament. So I need to see if
that's what an 80 needs. I think it probably is. And then we've got this amplifier volts,
amplifier filament, volts and amperage. 2.5 center tapped at 3.5 amps and 2.5
at nine amps. So that's what I was kind of thinking was going on. What they're doing is
they've spread out where the filaments connect so that they don't run into a problem where
they're pulling too many amps off of one winding. So I think my best course of action is to just
hook it up exactly to the same lugs that it's on and just hope that they did it properly the
first time. They probably did, right? So this is the dimensions and then this is the weight, 5.2.
So I'm going to look up a 80 tube, rectifier tube, and make sure that 3 amps is cool,
or milliamps. Did it say milliamps? No, it says amps. Okay. Yeah, I thought 3 milliamps wouldn't
work. And then let's see the amperage of the other ones. There's a 2.5 center tapped
that's three and a half amps. And then there's a 2.5 that's nine amps. So we may be able to
figure out the math and just make sure that it all makes sense. And then if I test the
windings, I should be able to tell by the way they're running the wires that they're running
these two lugs they have as a pair. So that should be a winding. So I should be able to
test across the winding and see if we've got a nice resistance there where it's connected.
So I'm going to have to do a little math, well not math, but a little documentation
because I can't find a wiring diagram. It's probably the same for all of these stand cords.
It looks like this must have been some huge transformer company and is real quality nice
stuff, right? Oh, and I'll read you this because it just looks cool. Universal 1.5, 2.55, and 7.5
volt combination transformers, long popular with the servicemen. These units have been retained
for their special filament and plate voltage combinations. In this group, the 1.5, 2.55,
and 7.5 volt filaments are found. Also plate voltages for type 10 and 50 tubes. They are
universal in mounting and will fit a great variety of installation requirements. Individually packed
with connecting instructions where needed. Attractive, carefully engineered, well-made
half shell transformers for replacement in sets using this type of mounting. The transformers
listed cover a large variety of electrical specifications and are equipped with
electrostatic shields. Built of the finest materials available, obtainable, manufactured
under close supervision, and vacuum impregnated. The stand core way to ensure long dependable life.
These units have been leaders in their field for many years. Each unit individually boxed with
wiring planogram. So I believe them. It looked like a nice quality transformer to me. So let
me see what I can figure out with a meter. All right. So the 80 full wave rectifier does want
five volts to run and the current is three amps. I'm sorry, two amps. And our transformer supposedly
is putting out three amps and five volts. So that's of course uninspected. I'm sure all of
this is fine, but I just want to double, triple, quadruple check and maybe I'll learn something.
So this is what I came up with. It actually all lays out and makes sense if you follow it.
All right. So pin one and pin three are the primary. So that's the power coming in and it
measures 4.3 ohms resistance, which seems what I've ran into on pinball machines and stuff like
that. So that's pin one and pin three. So they've got the primary running in there.
And again, I measured the ohms between them and they worked. Okay. So pins two and pin six
are the plate connections for the rectifier two. Now remember those are like a high voltage. It's
like 350 volts or something. And the resistance across those, all the way across them is 264
ohms. So that would be this coil here. So it's 264 ohms from here to here.
So that seems correct too, because it's a very high voltage. And then pin four is the center
tap for that. So you've got two, four, and six is a center tap winding for that. So that is two,
four, and six. So they've got a secondary center tap right there. And then they've
got the two primaries right there. Makes complete sense. Okay. And also if you measure from the
center tap to one side and the center tap to the other side, you get a pretty close number.
So you get like, if it was perfect, it'd be 132 each way, but you get like 136 one way and 130
the other way or 128 the other way or something like that. So it's cool. So those all seem to
check out fine. Okay. So then pins eight and pin 10 are the filament winding for the 80 rectifier
tube, which is five volts and it measures 0.2 ohms between pin eight and pin 10. So that is
these two. So they've got their center tap plate voltage, right? And then they've got
the two filaments for the 80, which need to be five volts. Then you've got your two primaries
here. So that leaves these four and that one. So five left, right? So pin seven is connected to
ground, which would be the center tap of the center tap connection that they were talking
about, right? So five to seven is one and seven to nine is one. They've got seven connected to ground.
So five runs to the positive filament of the two output tubes. Pin nine runs to the negative
filament of the two output tubes. So that would be 2.5 volts. The resistance is 0.1 ohms, which
sounds a hell of a lot like a short, but on these transformers, one, they're making a low winding.
And so it's a very low voltage and it's just wire. I mean, so you're literally just measuring
across wire. So the resistance is going to be very, very low. I'm sure you could get a
meter that just goes way down below one ohm where you could figure out exactly what it is. But
in a situation like that, whenever you've got something that seems shorted on a transformer,
it's usually just that the winding just doesn't have much to it. If it's only wound around there
a few times, the resistance is going to be very, very low because you're sending voltage right
through a wire. So it's 0.1 ohms. It's interesting too that this one is 2.5 volts, supposedly,
and it's 0.1 ohms. And then this one is five volts and it's 0.2 ohms. Seems right.
And then when you've got 700 volts between these two, not really, but it's 264 ohms.
It kind of lines up, kind of. The math doesn't really work like that, but
if you've got a higher voltage, you're going to have a higher resistance on the winding.
Okay. And so they have split this one that's center tapped. And I believe that was the one
the lower amperage, if we look at the catalog again. They have split it and ran it to the two
output tubes just by itself. And then they have every other tube, one, two, three, four,
the other six tubes on pin 11 and pin 12, which must be the badass one that's got like nine amps
or something. So it can run six tubes. So it actually, it all lays out really well. So I
think they probably hooked it up properly. Oh, and the resistance between that one and that one
is also 0.1 ohms. So you've got your two primaries here and then a center tapped winding that they
are using for the output tubes. And then you've got a center tapped winding for the plates.
You've got the two lugs for the filament voltage, which is five volts. And then here on the end,
you've got two lugs left. That's the nine amp winding that they've got running to one, two,
three, four, five, six tubes. Okay. So I'm going to look up all of these tubes and see what kind of
draw they have and just make sure that we're not overspec or anything. I'm sure we're not,
I'm sure this, this transformer is probably four radios, just like this, but I haven't worked on
a ton of transformer sets. So I just want to double, triple, quadruple, check everything
and make sure that I understand what's going on. And also, this is how I learned,
you know, a lot of people, they learn by listening to somebody else, tell them what to do. I like to
like, you know, get in the middle of it and try to figure it out and touch it and get shocked and
you know, and I learned a little teeny bit each time. And eventually you get a little better at
it because you, you messed around with a little bit. So, um, I'm going to, I'm going to look up
all of the tubes and then add them all together and see what kind of current draw supposedly they
have. Okay. So I've figured it all out. The, this line here is the one that we've got.
So the 80 rectifier uses two amps and it at five volts and this transformer provides three amps.
So we're good. The outputs, the 45 outputs use one and a half amps each and they're hooked up
to the center tap, which conveniently puts out three and a half amps. So it uses three,
the transformer's putting out three and a half. But then the problem we have is we've got six
tubes left. We've got three 27s, which is the oscillator, the second detector, and the one A,
I don't know why they call it one A, I don't know what that is. Um, and then we've got three 24s,
which is the first IF, the second IF, and the first detector. All of those use 1.75 amps,
which means those six are using 10.5 amps and the transformer puts out nine amps.
So it could be that, you know, some radio guy and he knew that it doesn't actually use 1.75
and that nine would be good enough, you know, where it won't, um, uh, maybe he knows that in,
I don't, I don't know. Maybe he knows it's like the 27s never actually use 1.75 or the 24s never
actually use 1.75. I don't know, but it's a little bit undersized. Now, if you look on this list,
these up here are C, uh, mounts. So they, it's just a different, instead of having lugs that
you can solder to, it has wires sticking out of the transformer. Uh, so that wouldn't have worked
as well for their setup. Although I, I guess it depends on how long the wires were. They could
have ran them out of the transformer over to wherever they need to go, but we've got this
one here. So this is, uh, for the rectifier filament, five volts, like we need in three amps.
And then it has, uh, wait a minute. Now let's look at the one above it. Five volts and three amps
for the 80 and then the 2.5 center tap for three and a half volts, which they would use for the
45s. And then instead of having nine amps, this one is built with 14 amps. So our 10 and a half
amps would have worked perfect. So if they would have picked that transformer,
it may have been a better fit. But again, I don't know enough about them. It could be that
nine is completely sufficient. So it's type C mount P 40, 40, P 40, 44.
And the C mount looks like that. Maybe that just wasn't even similar to the original transformer.
So they didn't think that that would work and they wanted one that looked like that,
but we'll see how it ends up. We'll see. We'll see if, uh, it works like that. Um,
so we've, we're running 10 and a half amps, but supposedly the transformer can only
handle nine. And we're not positive that it's going to draw 10 and a half with all of them
together, but that's, that's the numbers, but it does look like everything's hooked up properly.
I need to fix the wiring that screwed up and, uh, um, we'll add that to our list of things
that may be a problem. All right. So I fixed some of the bad wiring. So there was one wire
that went from here down to here. That was a double is taped in the middle. I went ahead
and swapped it because I had it. And then there were two wires that went to, I guess that's the
filament of the rectifier. And I think those may have been the original wires, but they,
they sleeved them in rubber because the wire inside is just fried. So it could be that they
use the same wires, uh, from the original transformer and the original transformer melted
down. Um, so I swapped those nice new wires. Okay. And then I took the two that were coming down
here and taped together and then, uh, slid over to here and cut that off and rerouted them. There
are two, there are little holes through here, rerouted them through to there. There was a
little Nick in that one. So I put some tape on it. Um, and then the other two that were tied
together that were routed down here, did the same, took them loose, took them down, put them where
they go. Uh, you could probably just get away with one. That's how they had it. They had two
running into one wire going over. Um, but I figured, you know, since I had both of them already
hooked up, that may be the original design anyway. We'll just leave it like that. So I think this is
all wired correctly. I think everything's fine. Um, there's no more wire that's screwed up.
We've replaced all of the capacitors. We've checked and replaced all of the bad resistors.
We checked all the coils. Uh, I think what we're left to is trying to see if the thing will power
up, um, just the transformer. So I'm going to do a little, I'm going to look at the schematics and
make sure it's safe to do that. And if it's safe to do that, we'll fire it up and see if we can
measure some of the output of that transformer. Another thing I think that I figured out was,
you know, I was trying to figure out why they were routed over here and then
jumped it over to there. And I was talking about how I was going to reroute them.
I think they were because they were originally attached to, this is the rectifier and these are
the two output. So I think, um, if you look at this, it clearly shows on the schematic that
there was only one winding, uh, for all of the tubes except the rectifier. So, and it even says
thick leads coming off the winding over to the outputs. And then it shows more lines running
over to the first detector. And then it shows, and it shows those three altogether. And it doesn't
really just show that those link over, link over to here. It shows that there are wires going over
there. So I think that they, I think they had those big lines coming down here. One of them,
one set was probably attached to this output tube. And one set was probably attached to this
output tube. Um, and they were jumpering the power over to here and then here through the little line
and then up to the top. So I think that's why all of those were routed down this way.
And whenever they changed the transformer, they just took them loose because they figured out
that they wanted to do those separately, taped them together and ran them over. So it all makes
sense. Okay, folks, I think we're good to test it. I don't have any of the, um, any of the tubes
in it at all. Um, we're just going to see what the output of the transformer is or attempt it.
I've got a power cord clipped into it. I've got it running into an amp meter,
got a two amp fuse installed. The amp meter is running into a Variac. Variac has a two amp
fuse installed. Um, and we're going to plug it up and see if we blow fuses all over the place,
all over our, uh, secret bunker here. The Variac is on zero at the moment.
Variac is plugged in. Amp meter is plugged in. Radio is plugged into the amp meter. Okay. But
like I said, it's on zero. So there's this power switch on the front of this thing.
I would assume up is on. So I'm just going to give it a little bit of power and see if we
start shorting. If there's a short, it'll start drawing all kinds of amps and blow the fuses.
So right now we're on this middle, on this middle gauge here. I usually use the low one,
but I think this may actually use more than one amp. It probably won't use much at all with no
load on it, but we'll see. So I'm just going to turn up the Variac very slowly. We're just
looking for shorts. There's nothing to warm up. You know, we're not, um, most of these caps won't
even have power on it. And the field coil is removed because the speaker's not plugged up.
That's the air conditioning coming on about made me piss myself, but that's okay. Yeah. So there's
like no amp draw at all, which might mean I've got it turned off. So I'm going to turn it back
down to zero. I'll flip the switch the other way. Perhaps that's the one, you know, flipping it down
makes sense too. This is old school. Nothing. Hmm. I'm going to have to use a meter to make sure
we've got voltage on the transformer. You know, there is a light on the dial, but I don't know
if the bulb's any good. Let me turn it back down. Let's switch the other way. It's not labeled
on or off. So I'll turn it back up. I think the only load at all would be that bulb.
And I don't even know, you know, that, let me look. Is the bulb even on the AC side?
Uh, yes, the bulb is on the filament winding. So if the filament winding is working, the bulb
should come on. Yep. I can hear the transformer. She's back. Okay. So, uh, let me, um, set this up
so that we can check the voltage. Okay. So I've got the Variac set on what I believe is about 110.
I don't know how we would ever find out what, what do I, let's see. Let's see if I can tell here,
um, what we're getting to the transformer. What do you think? Am I, am I testing the right ones?
There's the power coming back. We're on AC. We're checking voltage.
Uh, let's check. Well, what's the best way to do this? 106. Yes, 106. Okay. That's about right.
I'm just guessing on the Variac. I know it's off a little bit of the, um, the, the dial on the
Variac because it was set up for when wall voltage was 110, but now I'm running like 125 into it.
So the Variac itself, if you put it to where it says 110, it sees that as a hundred percent,
but a hundred percent is 125. So it's off a little bit. So I kind of got a guess I've marked it, but
it's not exact. So we're at 106. Maybe I'll turn it up just slightly and see if it gives us a little
more. All right. So we're operating it on 111. Okay. So first let's test, uh, let's test the
filament voltage of the, uh, the freaking, um, G80. 5.18. It's supposed to be five,
but there's no load. So that sounds right. Okay. Next filament voltage of the,
the one output, uh, the center tapped output for the, uh, uh, output filaments 2.88. It's supposed
to be 2.5. It's unloaded. All right. And then next the filament voltage for everything else.
Which is the nine amp filament voltage. Those numbers jumping around are because I'm not
holding it very well against, I don't want to push the radio. 2.87. To me, I think that's like
dead on the money. I don't know what, how it's going to be with a load on it, but
seems rock steady. It would be interesting to turn it up to 125 to the wall voltage and see
how much higher that is. Um, you know, if it makes it, if it puts it through the roof.
Okay. Now here's the big one. Here is the big one. The plate voltage of the rectifier. You know,
that's the most likely to burn slapped crap up. So I'm going to test them one side and then the
other. So here's one side 3.56. Here's the other side 3.56. That's a working transformer people.
I was real worried about that. I thought that transformer might be screwed up because obviously
they've swapped it, but you know, I haven't done a bunch of these, so I didn't realize that that
was a really nice transformer. We still have the issue where it's only a nine amp supply and they
seem to have 10 and a half amps worth of tubes running off of it. Um, but let me tell you how
I think. I don't know what I'm doing. So to me, that seems pretty obvious. You're not supposed
to do that. But some radio guy that knew what he was doing enough to swap this transformer,
if I was going to guess, probably back in the fifties, um, he thought that that was fine. And
we're sitting here checking the transformer and it has not burnt up yet. So, you know,
if there was an issue, you would have think that you'd think that it would have burnt the
transformer up by now, but I don't know, but that's how I see it. So in other words,
I'm going to defer to his judgment and assume that he knows more than I do about it. Cause
I don't know much, but I'm learning. Okay. So I actually ordered, um, some of these catalogs
just because I thought it was pretty cool how they had the information in it. And you might
run across them some more. And apparently this Stancor company made some really nice stuff.
And so it's probably common if you find a replacement transformer, maybe it came from
them. This book is prepared as a complete reference and guide to the finest line of
radio transformers, reactors, and packs available from one source. And this is from 1943. Um,
so they've got all kinds of stuff. The one that we had was the P2859, I believe,
page 11. It was $5 and 15 cents when it was new. Wow. All right. So let's see page 11. When we
were looking at it online, the page was split. So it was kind of hard to read it. Stancor power
transformers, uh, represent the last word in efficient transformer construction. They're
designed for compactness without sacrificing efficiency. By the clever use of two special
mounting screws, these transformers may be mounted either as two or four hole mounting half shell
transformers. Four universal brackets permit they're being mounted in either vertical or
horizontal position. Uh, position special studs provided under provide underwriters type mounting
transformers equipped with eight inch flexible RMA color coded leads and static shields.
So those little bars that were used to hold it in may have came with it. I guess they may be saying
half shell transformers, half shell with lugs, 2.5 volts. So here's ours. Uh,
no, ours must be the 2860. Number of tubes, eight to nine, plate voltage center tapped, 790 milliamps,
filament one, five volts and three amps. That was for our five volt, two amp rectifier tube,
uh, filament two, 2.5 center tapped, and it's 3.5 amps and filament three, 2.5
and nine amps. So just what we were looking at online and it was $5.45.
If possible, order items preceded by a star.
That's awesome. Hey, by the way, if you're going to order something, if you can order some of the
ones that have a star on it. Okay. Uh, chokes, plates, filament, transformers, isolation,
transformers, tube chart. Pretty wild. Oh, look, there we go. 45, 2.5. They say it's 1.5.
Is that what we were? Oh, we already saw that. 1.5. That's right. The other ones were what? 27.
They may not list it. Maybe their opinion was they weren't 1.75 amps. I'm trying to make this
work any way I can. When performance counts most, professional series transformers. Now,
I don't understand why there are two catalogs though. So there's that, transformer standard,
transformer core. Oh, that makes sense why it's stand core. And this says replacement and general
purpose transformers. And I believe, see, this is 1943, but it says September 1st, 1943. Maybe
this was like updated prices. Let's see. No, it's the same. Note, this price schedule supplants all
previous price lists and these prices were in effect October 15th, 1941, and may be changed
without notice subject to approval, but it says copyright 43. So I guess they didn't upgrade them,
change them too much. Here we go. Oh, you know, I didn't think about this was during World War II
that this manual was printed. So let's see what it says. Because of restrictions,
overtaxed production facilities, raw material shortages, et cetera, it is virtually impossible
to main stocks of all units listed in this catalog. To help in correcting this,
production is being concentrated on the items which demand has shown will serve the greatest
number of applications. These are indicated by a dot. All unmarked items will still be available
as sufficient orders accumulate to make production runs feasible. That's understandable.
So our 2860 does not have the dot. So apparently, you know, it was probably because it was old
enough that they weren't selling a ton of those. Audio transformers, interstage transformers,
driver transformers, modulation transformers, output transformers, output transformers,
power transformers, power transformers. Whenever possible, order items preceded by a dot. Yeah,
okay. Makes sense. Chokes, plate transformers. Well, we solved that mystery. They wanted you
to order what had a dot because they were in the middle of a war. And let's see if it says
the same up here. If possible, order items preceded by a star. Restrictions, overtaxed
facilities, shortages, et cetera, make it virtually impossible to maintain stocks of all units listed
to correct this production is concentrated on items which serve the greatest number of applications.
These are indicated by a star. Unmarked items will be available as orders accumulate to make
production runs feasible. So the same thing, 1943. This one is a much bigger book though.
So I don't know, maybe it doesn't have September stamped in it like that one does. So maybe,
I just don't know why there's two of them, but whatever. Very nice. They're in pretty much
perfect condition. So that'll be a good little reference for if I need to look anything up in
the future. But look, October 25th, 44. September 1st, 43. Okay. So actually, this is later.
And it's more in depth. Maybe they just, the company was growing or something.
W.R. Holben, Davidson 7361, servicing of radios and electrical appliances.
14222 Greenlawn Avenue, Detroit, Michigan. So Detroit has had some hard times over the last
30, 40 years, and this is actually the house. That's a house. It says Greenlawn Street,
but I looked on Google Earth, and I guess it used to be called Greenlawn Ave, and then they
changed the street at some point. But that's the actual house where the gentleman lived that got
this manual mailed to him in 1944. And this house, believe it or not, is for sale for $2,000.
But it's Detroit, and there's just sprawling areas of Detroit with tons and tons of houses.
I don't know what to believe, but I heard that there were even areas of the city that they were
trying to shut down because the city is such a sprawling city. They had problems with
trying to govern it all after so many people left the city. So if part of the city is a mile and a
half out, or even maybe even farther, hell, that'd be small. I'm in Charlotte, and it's probably
10 miles around, something like that, maybe more. But if part of the city is 15 miles in
that direction, this street, for instance, if they can help it, they don't even want to continue
running water out there and running sewer out there, because it's just everything's so big,
they can't handle it all, since so many people have left. So you can buy some of these houses
really cheap. So this house is for sale, I'm sure it's condemned and everything, for $2,000.
And there's some kind of government program, the Own It Now Sales Program.
Own It Now Sales Program. Step one, register and review Own It Now rules before bidding. View
properties by appointment. Budget for significant rehab expenses. Step two, submit highest and best
offer. Selected purchaser will be contacted and charged for the deposit. Closed within 30 days
unless seeking financing. Rehab and occupy the property within six months. So they're trying to
it's sad seeing an old house that's just so run down. It doesn't look that bad from outside,
it's just boarded up. And there's a nice little house next to it. Maybe somebody ought to go get
it. I didn't realize that they had picked a bunch of pictures. So this is behind the house,
I wonder if that was his little radio shack. Yeah, that very well could have been where he fixed the
radios. It's a small house, it's only like 1,040 square feet. So he may have worked on the stuff
outside. And I don't know how much work he did. I mean, it could have just been a guy that was
interested in it and called them and asked for a catalog. These pictures were all taken in 2020.
To be honest, it's probably much worse now. All this can be fixed easily.
I've got another channel that I do with my brother and we work on old buildings and old
mobile homes and stuff like that. All of this is very fixable. You have to go in there and
really the problem you would run into is how serious is the government about
making you do things a certain way? Yeah, you got to do it to code,
you should do it to code, but do they have a bunch of ridiculous...
You know one of these rooms had to be full of radios back in the day.
Do they have a bunch of ridiculous rules and things like you got to have
certain types of materials and who knows. Yeah, that's sad then. But that's where our manual came
from. It got out before things got bad. All right folks, that's enough for today. Next time we'll
mess with the tubes. I got to figure out how to test them. I don't have a tube tester that
mentions anything about those old tubes, the ancient ones.
Then we're going to have to work on the speaker and then we're going to have to try to fire it up
and then there's still a few things left on the chassis that we got to do. We've got to
fix the tuning condenser. We've got to clean and rebuild the tone control and we've got to
clean and rebuild the volume control. I know there's like four things there I got to mess with.
I think there's a tuning capacitor that we didn't get that's like a sardine can that's up
behind it. We might leave that on there just to see if the thing still works and then why that
would probably be a really safe one to leave in there if it's all original if it still actually
works. Then we have to work on the cabinet as well. It's in pretty rough shape. Well,
it's in pretty good shape but it could sure use a little bit of refinishing. I'm not going to
refinish the whole thing because I'm not talented enough to do that but I am going to refinish at
least the top and try to touch up some of the other areas. We'll see what we can do there.
We got a lot more to do but next time we will work on the tubes,
the old style tubes. I will see you then. I hope you enjoyed it. Leave your comments down below.
