http://www.VideoJoeKnows.com Fixing a sagging door (Part 2) is easy...when you know how. OK your door is rubbing at the top & not closing properly. what is the problem with your door? More than likely it means that your door is sagging at the top & you need to get it fixed! Guess what....you can do it yourself! Yes you don't have to be a bonafide carpenter in order to fix your sagging door. & you will be saving yourself some money too!...as if you didn't know. Ha! Joe is just an average Joe & if he can fix a sagging door, so can you. Just follow the steps Joe will show you & you will see that you can fix your sagging door. A few strategic screws & presto. Sometimes you may have to do a few other things to your door as well, as all sagging doors are not created equal, but most of the time, this instructional howto video series will do the trick for you on your pesky sagging door. Check it out! http://www.VideoJoeKnows.com
AI Generated·May contain errors
Now I don't use this drill very often but it's my backup plan in case my battery operated drill
stops working or I gotta charge the battery and I don't have an extra battery whatever.
So when I put this in I just want to grab the tip and when you tighten this
you want to tighten it on one hole then you want to turn it and tighten it on the next
turn it tighten it on the next that way you get it overall you get it on there nice and snug
okay if you're just doing one you're not getting it in there right and it might get wobbly or it
could even come loose I've had that happen so that's kind of why I do that and I've got some
goggles on and you know what I got my earplugs so I'm taking a little napkin and I'm going to
stick that in my ear my ears get kind of sensitive and that's probably from over time over the years
I wasn't wearing earplugs so you got to get yourself a set of those you know if you're
going to start doing things on your own instead of paying somebody else you can save some of that
money and start investing it in some tools and some safety goggles and safety wear and all that
kind of stuff okay let's do it get those holes drilled see what we got getting over a cold too
so hopefully that doesn't bother you let me sniff on a little bit okay I'm going to just go in a
little bit out in out in out you don't want to drive it in there in one go you could snap the
drill bit off or it accumulates a lot of wood on there you got to keep pulling it out to clean your
bit so I'm going to kind of put it in at a slight angle kind of go in just a little bit of an angle
not too much but not straight either because you may hit the very edge of your stud and then when
you're putting the screws in it could go out of the edge of the stud and what have you I'm going
to go ahead and put all three in well I can feel that studs is kind of hard so I hope I can ram
these screws in which I think I'll be able to we'll see okay let's see if I can drive these all
the way in with this drill you know battery operated drills believe it or not seem to be
stronger than the power ones because these might not be able to torque it all the way down we're
going to try it and see I've got my other drill here just in case I need it make sure you put
them in the right holes because see we don't want to put them in any of these other four holes and
if you're thinking hey Joe why not just take one of the screws out and ram a screw into here
and and use that and be done with it well you can't suck this jam in far enough that way depending
how far you want to go we want to try to shove it in as far as we can so that's why we're we're doing
it on the back side then you won't see these screws make sense I don't even care what color
these are or anything like that I want to make sure there's a flat head so they go flush to the
wood I don't want the round head ones wow that went in good just doing a little trigger at a
little bit at a time I want to drive these in as far as I can to help suck that over now if there's
a shim on here I might not be able to suck that over a whole lot but any little bit is better
than nothing right we're gonna I got another step to do after this if this doesn't work all the way
there okay now I can lift that back up and put those screws in if you're doing it by yourself
you just have to think about different things because I have to raise that door up then I got
to hold it in place put a shim underneath the door all that kind of stuff so see I'm gonna
I'm gonna close this door just a little bit not a whole lot but enough
so I have to get it over to about there so that I can now lift that up and put something underneath
there and see I was gonna put my cat's paw my cat's paw is too thick so now I'm gonna have to
see what else see what else I can do over here see if I had a second person here
okay let's try that I got lifted up a little bit now my hinge is in the right place but see
like the door's too far I can't screw it in I gotta slide it back over a little bit
over this way so I can reach I gotta have enough room you see I gotta have enough room to reach in
there and put those screws back in by hand without hitting the edge of the screwdriver on the edge of
the door okay that's up tight exactly where it was before I'm gonna use the same screws
these screws aren't very long these are the existing ones that came out of here
and if they're already spinning or loose or you're afraid that you're going to tighten this up if
they're not holding then that's going to cause your door to sag too so you know if you wanted
you get longer screws drive them in further or even two inch long screws let's say so it goes
through the door jam which is three quarters of an inch usually have a quarter inch to it
the three eighths gap between that and the two by four where the shims are to attach your
door jam so you can plumb it up and make it level and all that good stuff and then you could drive
those the rest of the screw length right into the two by four that would be the best way
in a perfect world okay but these seem to be snug from before and if I can get these in they're
tight see that feels tight I like to put these in I mean you can put it in with the drill again
but I don't want to strip the head a little bit or or you know if these are barely grabbing let's
say you put them in with the battery operated drill or something like that you could spin them
and then they're not holding are they see now I couldn't I couldn't have had the door
opened all the way at a 90 degree angle uh because if you put it at a slight angle it
kind of gives you more room to kind of shim it up here you know and I guess I could have
I could have ran it straight and put a shim in there but I like to do it this way
it seems to work out all right okay okay now we're going to see how well the door
is sitting at this place when we close the door another option you could get it a little
bit further by doing the other hinge you know the middle hinge we could do the same thing
we could do the same thing to the middle hinge right down there now we can pull that out
and we could pre-drill that again couldn't wait and put three more screws in there which I may
end up doing and at the bottom we don't have to do anything because we know the door was
sagging at the top hinge and so that's why we're trying to push that jam over okay