How to fix a door that is not latching...Part 2

VideoJoeKnows
63 followers
Apr 22, 2026
http://www.VideoJoeKnows.com How to fix a door that is not latching (Part 2) is easy...when you know how. I hate it when you
close a door & the door latch does not keep the door closed. Why is this door not latching properly I ask. When I
look at the door it seems to close ok but then the door latch does not catch & the door does not stay closed all
the way. The door used to close just fine, with the door latch clicking into place like it should. Why does it not
do this now & how do I go about fixing it? Just watch "joe" & see what he does to ensure this doesn't happen again anytime
soon!
http://www.VideoJoeKnows.com
Let's try that bottom latch now. I've only worked on that bottom latch so far.
I'm going to close it. Look at that. It's latching every time. I'm going to check this four or five
times before you call it good. Okay that's holding good. Got that one fixed. Am I done with that
bottom one? Well let me give you one more thing I do before I call the bottom one good. Now this
latch is working good now but here's one more tip for you. I want to do, I want to shave this a
little bit further right here. That way if this door ever sags just a hair further I'm not going
to have the same problem will I? If I drill this out and shave it out just a little bit more.
The bottom of this I'm hitting, I'm now hitting the wood that's back on the back side of this
strike plate. That's okay. I've got my reamer bit out. I just want to kind of glaze over that
wood too to get that a little bit lower so you can get this little edge down a little further.
See this edge right here? That's where it was, that's where it was rubbing before about right
there. See how much I've reamed down? Now see here's the screw that's holding this strike plate on
and so I can't go down much further than that. See this little curly cue right there?
You should probably get that just a hair deeper there and work on that just a little bit more
right in there so I can kind of get that down a little bit. There's only so far I can go because
I can't make a perfectly straight corner there with the bit I have right? But if you've got
a different type of bit you can make nice little sharp corners. I don't need to really make a sharp
corner as long as I have the lower portion low enough so it's not going to hit where this angle
is. But I'm going to make that angle a little bit further down and it'll work out better in case
that door ever sags again. That's a little better. I probably need to get a new bit. This one's
getting kind of dull but just because it's dull I know how to use it in such a way to where I can
get my project done. The next time I'm at the store I got to remember to get another one of
these bits for next time. Now that I got that far am I done with this hole? I hope your answer was
no. Because see once I reamed that out I've got a sharp edge at the bottom of it. I don't ever want
anyone to cut themselves, rip their finger open on that, catch it with something as they're coming in
or even the door hitting that. So I'm just going to file off that edge with the same bit.
Make it nice and smooth. That's more like it. You'll see here on this this end over here it's
got kind of a big curve in there. You might think hey why didn't you hit that too? Well
when the door closes the door has that latch on there. The door latch is never going to touch
from about from here from here over this way. I could have left a big old hump there if I wanted
to because as the door closes and latches it's going to fit from this point over to about here
in the hole and that's about it. Did you know that before? Now you do. But I still want to make this
halfway decent right there nice and smooth over and stuff like that. Okay do a good job. Check
this out again after I ream that. Okay let's work on this dead bolt now. I'm gonna work on that dead
bolt now because that's still rubbing. Do you remember? Don't forget that. This handle was loose
too. Look well with paddle handles this is loosened up and it's fallen all the way down so I'm going
to kind of lift this up and I can see how that's going to cover the hole better too.
But the bottom of this is showing too from where it's sagged down.
We may have to split the difference a little bit and tighten that in. Some handles aren't as easy
to just tighten like like this but if you see the screws that one was loose too.
Do that double check that make sure the latch is pushing in everything's fine.
Okay a little minor cosmetic surgery on this door is all that was needed.
