https://www.youtube.com/user/VideoJoeShows My solid core garage door is sagging what do I do now is what this DIY howto video is about. VideoJoe is working on a door that goes out to the garage & this door of course is a solid core door & yes it has spring loaded self closing door hinges on it & yes this heavy door is sagging. This solid core door is over 17 years old & over time it's normal for a door to start sagging especially solid core doors. He's already fixed numerous interior hollow core doors that were sagging & the doors were 8 foot tall & you would think since they were hollow core doors maybe they wouldn't sag at all but oh no....lots of them were sagging if you've been watching VideoJoe's videos! He's showed you lots of ways to fix sagging doors & adjusting doors & tightening up door hinges & adjusting door strike plates. He always tells me "hey the more you watch my videos the more you will learn" & he's right, ahem! Watch & learn as VideoJoeShows you what VideoJoeKnows...My solid core garage door is sagging what do I do now. Nice! https://www.youtube.com/user/VideoJoeShows
I just want you to see what I'm doing as I'm doing it, okay?
Okay, so let me I'll just keep running
Get my
Drill all set up here
Screws out see how I'm taking the screws out first you take one or two out
This is gonna spring back, and then you're gonna be like oh, what do I do now?
That's when you gotta take the spring tension off of this thing
All this work just to
Get this door fixed, but hey
I want you to see you don't have to be a professional
door
Person to do this if I can do this you can do this all right. That's what these videos are all about
On my channel most of them anyways, but I'm excited
I'm gonna
I'm making some travel videos. We're gonna put mommy and I are gonna have some travel videos up there to about our
Travels and stuff. I think you'll like that okay, so I'm just getting my
small screwdrivers
Now
Eighth inch drill bit here
And I'm gonna let most of the drill bit stick out of my Chuck
I'm gonna just grab the tip of it. Maybe a eighth of an inch of it
Don't want to get most of it in there
And I'm gonna drill
This I'm gonna slightly angle it
So I make sure that I don't I don't want to drill straight in like okay
It doesn't matter where I do it the first half inch of this inside the house is sheetrock. I got it
I got to get
Beyond that so I hit into the stud this this stud incidentally is a 2 by 6
This is a 2 by 6 wall instead of a 2 by 4 wall thus this frame is that much
Stouter so once I drill these I'm not I'm not thinking I'm gonna do much
I can see where they nailed this in or screwed it in
I don't think I'm gonna be able to move this very much, but I'm gonna I'm gonna make the
the Joe effort anyways
Okay
I'm gonna have to get a new battery. I've got one charged up and right back
Oh
Video Joe is not as young as he used to be that's for darn sure
On the stairs get this
Okay
I'm gonna put three inch screws into here. I'm gonna try to suck this in. I don't know how far I'm gonna go
I see there's a nail
Right there. There's probably a shim back there. It might be a nice solid shim. I might not be able to
To push it back much, but I'm gonna give her a go I
Could do the two and a half inch first
Take Ted kind of help, but I think I think I'll be able to do it with these threes. Let's see
I'm gonna back it off
So I can get another go at it. Okay, that's as far as it's gonna go
Okay before I put that next one in I'm gonna I see where the nail is you might not be able to see it
I'm gonna take my crummy flat
Putty knife on here. I'm gonna whack on that that way. I don't put it in
Screws too, but I'm not gonna dig this out and if I wasn't going to
Have this painted I could get some simple green and get that all cleaned up, but because it's gonna be painted
There's a slight little mark there. It's gonna be covered
Okay
Thought that might help it a little bit. I should probably done that before I did the first screw
Okay, which way
Let me try that again
Because this screw could have been held
Holding this up. Okay. Normally I don't count on the jams, but in this case, I'm going to
Put the screw in again
That might have helped putting the first screw in anyways and taking it out and see I got that
Pushed into the wood a lot further. I see I see where there used to be a screw head
Or a nail right here
And I couldn't see that before I started so I know I push the jam in a little bit right there. That's good
Next one
Boy I can get it off again. That's what I need to be up just a hair higher on a ladder
Okay there I did it
Okay
Yeah, I did actually push it in a little
I'm gonna take my putty knife again
And whack on the side right over here
Right where it goes so I don't put a hammer and push it in
That's good
I see where there's another
I see they put a nail here and here above each one, and it could be a screw, but I didn't really want to dig
I don't really want to dig that out
If there was a screw there, you could dig that out
maybe
Maybe put the screw in further
But I've got it. That looks good
Okay
now
Now I can push this back in
Okay
It's in there. It's in there
It's not hitting the screw head or anything
That's why I gotta make sure those are flush if not
Sunk in a little. I can put these screws back in
Once you use a drill a while you can you can kind of feel when they're tight
But I try not to do too much. I still go back and double-check
Okay, and I may have to do this second hinge
let's just
because because
You saw how much I was trying to push that over if I take this one out it might it might help the rest of the door
go in
So I think I'm gonna do that next one too, and that's not a self-closing one
so let's just
For kicks before I do that. I'm sure I'm gonna do it anyways, but I want you to take a look at this
Get this set back up, but I'm gonna take the camera off of the tripod
We're gonna close this now
I'm gonna see
Got any extra gap here. I mean it's it's more
It's nicer
And I still got
Quite a bit of a gap
Right in here and no matter what I do. I can't get this any closer unless I notch
This hinge into the door a little bit, and I just might do that I
Just might do that
because
See this gap is just about right here on this side, then it then it increases from here on up
So if I were to do the same thing to this hinge would it help this one a little bit. I don't know
maybe
maybe to a certain extent, but
The way it is right now. I want it to get more. I see something way up there. I don't know what that is
Cobweb
Okay, no matter what I do. I can't do it you see with it
There's a nail there and up there
But if I look on this next hinge see there's one there
And one there, and that's just what they normally
Do I guess on these exterior ones here's here's the other one over here?
They put big fat nails or or screws. I would say normally screws
I don't really want to dig that out and
Whacking that I think I I got it in there. There's there's no real way. I can suck it in anymore net
Okay, because the thickness and I got the casing there look how thick this casing is
and I
Just don't I know I'm not gonna mess with that top one anymore
Other than I may I may notch the door
So if I notch the door into the hinge that will allow the door to move over won't it just a little bit
Granted when you open up the door
You might see that on the inside this hinge is stuck in a little bit, but you're never gonna really notice it
It's next to your door going into the garage anyways
Okay, and because I'm not going to tighten up the spring yet until I until I fix this
All right, but for the sake of argument. I'm gonna take this one out. I'm gonna put two screws in there whack that a little bit
and
Before I actually work on the bottom one remember. I'm gonna work on the bottom one, too. I got a special trick for that and
in fact before I do any notching up here I
am going to
Yeah
Yeah, I think I'm gonna move this one first, and then I may not have to do any notching to that
Okay, so stick with me stick with me, and it'll it'll all come together here in a minute