Man Says He Can't Fix Sagging Door Then Does It Anyway...Part 1

VideoJoeKnows
63 followers
1 Video View·Feb 20, 2026
@VideoJoeKnows
Man says he can't fix sagging door then does it anyway...Part 1 is what this DIY howto video is about. VideoJoe is on a mission to fix a sagging door once & for all. Is there more than one way to fix a sagging door? Of course so you might just want to see how VideoJoe checks out this sagging door & goes about fixing this particular sagging door as you might learn something new! Watch & learn as VideoJoeShows you what VideoJoeKnows...man says he can't fix sagging door then does it anyway...Part 1. Nice!
https://www.youtube.com/user/VideoJoeKnows
AI Generated·May contain errors
Now that I got that fixed. I was going to do a few more things in here, and I've got a door
Right here. That's sagging slightly. It's not rubbing. It's not rubbing at the top just yet
But I have just a small gap there and when I push on the top of the door I
Can see that that hinge is moving and it's loose. I've got to figure that out. I want to get that thing tight
And fix so if you want to watch that keep sticking around
And checking out my videos
I'm just finishing up
This right here
not done until I put the
towels back up here
Where they were before and jeez I kind of forget. I think they were up at the top
Like they were up at the top like so
May have to play the video back and see I
Think they were like that
And then this one was folded over in the middle
Okay
Onward to my next project stick around and I'll show you what I do
For this sagging door now is there more than one way to fix a sagging door of course there is
And you've seen me fix sagging doors before
But you might
Learn something new if you check out this next video
Hey, Joe. This doesn't look like a sagging door. I thought you're gonna show us the sagging door well
Yes, I am, but I just got done fixing these two grab bars. They were loose
They were missing the end caps
And I just showed you how to fix that if you didn't watch that video you might want to check it out on my youtube
channel or my website
Okay, so now I'm over here looking at this door
right up here, and I was saying it was sagging and I'm looking at the top edge of the door and
Right in here. There's only about a sixteenth of an inch gap when I look down the door down at the bottom
I've got about a three sixteenth inch gap way down there
Okay
See here
See there
So big that gap is on the bottom, and it's almost rubbing the floor so if I raise that up
Can you see that if I raise that?
It will raise the bottom edge of that door
there
Okay, the gaps not that
Small up there, but I know
That it is
Sagging and why do I know that?
Because I'm the master when it comes to sagging doors, that's why
Here you take a look, and you're gonna see
That this hinge right push on the door up here at the top
See this here
How it flexes that tells me either the screws are loose here over here
Or the screws are are stripped or something is going on and it looks like there's a
There's a fairly large gap
next to the
Next to the door see how big this gap is
Okay, you look down at the bottom
The gap is smaller in it
See right in there. That's about what you want
Okay
And there's another reason why I know this is this is sagging a little bit this can be pushed over
And that's gonna move this edge over it's gonna raise that up right there and it's gonna raise the bottom edge of the door
up
Right there not over there, but right there, okay?
And so I'm gonna go ahead and open this door
And let's just take a quick peek. I'm gonna turn this light switch on see if we can't get some more light in here
Okay, the first thing I'm gonna do is I'm gonna look at this
hinge and
See if these screws are tight. Let's see there. I can just keep turning and turning and turning
That that means that that hinge screw is really not holding much is it?
Okay, that one feels tight
And this one's spinning
Okay, so there's two screws
Right now. I know are loose that hinge is only being held by one screw now
Let's see over here
What's going on?
That one looks tight
That one's just spinning
See there. I can just spin it so I need to get a
Longer screw in there
Okay, that one's tight. Okay, so this one is spinning, but in reality these two screws should be enough to hold that
Tight
This one here. It's only one screw. So I think I'm gonna I'm gonna change this out
But that tells me does that tell me that tells me that this jam needs to be sucked in there
Further that's gonna push in and I know it's I know it's can do that. You see here
Here's here's a finish nail right there and the head of it is already starting to stick out
The putty on the top of the head so if I can suck this in right there I
Can push this jam in sometimes you look maybe it's just your hinge is loose
You've got to put bigger screws in here or longer actually longer screws
But see I can't just put two long screws in there thinking I'm gonna suck the whole hinge in
It's not gonna work because I I can't push this right into the wood
Okay, so I'm gonna take this hinge off
And let's see if you can see see what I'm doing here
See, this was the one that was spinning. So that's really not doing anything
Let's see how big the screws are. They're not very long and after a while
If those are spinning
That's gonna kind of get your hinge
Moving a little bit possibly to see this one was spinning to
And the only one that was holding was this one
Boy, it's in there, too. So that's good
in fact, I
Might have fixed this
once upon a time
What somebody did
You see they put a longer screw in here. Let me get my drill out. I
Brought my drill. Ah
Get that I
Believe this was fixed once upon a time
And I might have fixed it once upon a time see here. I
Put two screws in here and pre-drilled it and put long screws in there and sucked it in
Already, that's why this head starting to peek out
Just barely so first off. I'm gonna make sure that that's tight
Now see if those screws weren't there you pre-drill a hole there and they're going into the jam you can't put it anywhere
Too close to this edge because you get your sheetrock half inch sheetrock on the wall
Sometimes five eight sheetrock on the walls. You got to get your screws in here
Into the two by four behind here. Okay, so this might not really go over any further
We'll have to see
You just have to see we'll keep this on here
And
Let's get this resituated. I brought my little
My little stool because I don't want to wrench my back out of whack
Okay, where did my stool go?
Here it is
See my stool. I take this around at different jobs
with this
Particular instance because if you're doing it off
The floor you don't get enough oomph plus you can put your
your
Shoulder out of whack
Okay, I want to make sure you can see this. Let's get you resituated here
Okay
That's looking good. Let's just see it. These screws are tight first off
I'm gonna back it out and drive it in
and it could just be
You're only gonna get so much flex there depending where your sham is or if the back of this
One by jam is pushed up tight to the two by four. Let's say
or anything like that, so
We're gonna have to I'll have to take a look at that
after and if and if it is
Tap that in so that's flush
There could be another way
That I could get this hinge in there
closer
by
well
I'm gonna I'm gonna tighten this up and then we're gonna see okay
I'll have to put some different screws in here to keep that pulled up tight
And worst case scenario if that's not enough and if I still have that gap in there follow this here
If you shave this wood down at an angle
with with a little
Chisel or something from about here over
Okay
Let's get you in there
From about here over let's say from here from nothing to about a sixteenth over there gouge this out
That will push this hinge over and we'll kind of push it in further
okay, and
This will push this up closer to the wall, or we could do it another way
I think I've got an idea for that, but first things first. I'm gonna go ahead and put the screws back in
Okay
And I'm gonna have to find some longer
screws and fortunately for me I
Usually always carry
Some sheetrock screws with me now see this was the one that was in there you see how long the screws were before
You know after many years these have a tendency to start
Loosening up because they're not very long and they're only going into the door jam
You see this screw is only less than 3 quarters of an inch long
So it's only going in the door jam
That's why I ended up using this one this one's probably a two inch and it's coarse threaded
Don't use fine thread, and it's a sheetrock drywall screw and see it's almost the same color
It's black. That's why I like to use them the head is about the same
Size is that and everything
Okay
So I'm gonna have to get that
I've got to push it back up into place
And because I'm here by myself
It's harder to do it. So see what I do is I go over here
And I take my trusty putty knife an older one
Got it
And I'm gonna try to shim it up with a screwdriver or something because I don't want to scratch up the floor
And I'm gonna push that up, okay?
Get my hammer
Get my hammer ready over here. Let's see. Let's see what I can do here
Got that there, and I can put my screwdriver under there
And that raises that up
Raises the bottom up so
That should put my hinge
My hinge about where it needs to be. Oh, that's beautiful see
That helps me, but if I had someone here they could just push up on that
Let's see you don't you don't have to have two people helping you
Just do a few of these things on your own and think okay
Joe does a lot of stuff on his own. What would he do?
figure it out
This one went right there in the middle
Okay there now I'm gonna have to dig for some longer screws for the other two
and
I'm gonna just put them straight in I can't really put them in at an angle
If I were to take this door off
I could put a screw in here at an angle
But then the heads gonna kind of be coming out at an angle
Because this one is gonna go straight into the sheetrock
Behind here you see what I mean unless I were to angle it about like that much almost at a 35 40 degree angle
to hit the stud in the back, but then if I do that that the point edge of the
Head of the screw is gonna stick out and somebody feels on there. They're gonna say. Oh great. What do we do about that?
Okay, so for right now. I'm just gonna find some longer screws
and
They're actually gonna have bigger threads on it, and I'm gonna drive them in here snug as a bug
in the rug and
I'll have to find I
Think it was this screw here. Yeah, see this one. It's just twisting
I'm gonna go ahead and take that one out, and I'm gonna put like an inch and a quarter screw in there
Cuz see those are only short to that's about five eighths of an inch long so if I use an inch and a quarter
sheetrock drywall screw
For that I'm gonna do that these two were still snug remember
Okay
Yeah, those are tight
That one's tight okay be right back for that
